标准号 |
中文名称 |
英文名称 |
| DIN EN 1010-4-2004 |
机械安全.印刷和纸加工机械的设计和施工的安全要求.第4部分:装订机、纸加工机和修整机 |
|
| DIN EN 1010-5-2005 |
机械安全.设计和生产打印机和纸加工机的安全要求.第5部分:波纹板生产机器以及平板和波纹板转换机器 |
|
| DIN EN 10106-1996 |
冷轧非颗粒结构定向最终退火装态下的电工钢片和钢带 |
(Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state; German version EN 10106:1995) |
| DIN EN 10107-1996 |
颗粒结构定向最终退火装态下的电工钢片和钢带 |
(Grain-oriented electrical steel (sheet and strip) delivered in the fully processed state; German version EN 10107:1995) |
| DIN EN 10107-2005 |
以完全加工状态交付的晶粒定向电工钢片和钢带 |
|
| DIN EN 10108-2005 |
冷镦和冷挤压圆钢棒.尺寸和公差 |
|
| DIN EN 1011-1-2002 |
焊接.焊接金属材料的建议.第1部分:电弧焊接通则 |
(Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding (includes amendment A1:2002); German version EN 1011-1:1998 + A1:2002) |
| DIN EN 1011-2-2001 |
焊接.焊接金属材料的建议.第2部分:铁素体钢的弧焊 |
(Welding - Recommendation for welding of metallic materials - Part 2: Arc welding of ferritic steels; German version EN 1011-2:2001) |
| DIN EN 1011-3-2001 |
焊接.焊接金属材料的建议.第3部分:不锈钢的电弧焊接 |
(Welding - Recommendations for welding of metallic materials - Part 3: Arc welding of stainless steels; German version EN 1011-3:2000) |
| DIN EN 1011-4-2001 |
焊接.焊接金属材料的建议.第4部分:铝和铝合金的电弧焊接 |
(Welding - Recommendations for welding of metallic materials - Part 4: Arc welding of aluminium and aluminium alloys; German version EN 1011-4:2000) |
| DIN EN 1011-7-2004 |
焊接.焊接金属材料的建议.第7部分:电子束焊接 |
|
| DIN EN 1011-8-2005 |
焊接.金属材料的焊接建议.第8部分:铸铁的焊接 |
|
| DIN EN 10111-1998 |
冷成型连续热轧低碳钢带和薄钢板.交货技术条件 |
(Coninuously hot-rolled low carbon steel sheet and strip for cold bending - Technical delivery conditions; German version EN 10111:1998) |
| DIN EN 10113-1-1993 |
适于焊接的细晶粒结构钢热轧制品.第1部分:一般交货条件 |
(Hot-rolled products in weldable fine grain structural steels; part 1: general delivery conditions; German version EN 10113-1:1993) |
| DIN EN 10113-2-1993 |
适于焊接的细晶粒结构钢热轧制品.第2部分:正火/正火轧制钢的交货条件 |
(Hot-rolled products in weldable fine grain structural steels; part 2: delivery conditions for normalized/normalized rolled steels; German version EN 10113-2:1993) |
| DIN EN 10113-3-1993 |
适于焊接的细晶粒结构钢热轧制品.第3部分:热工机械轧制钢的交货条件 |
(Hot-rolled products in weldable fine grain structural steels; part 3: delivery conditions for thermomechanical rolled steels; German version EN 10113-3:1993) |
| DIN EN 1012-1-1996 |
压缩机和真空泵.安全要求.第1部分:压缩机 |
(Compressors and vacuum pumps, safety requirements - Part 1: Compressors; German version EN 1012-1:1996) |
| DIN EN 1012-2-1996 |
压缩机和真空泵.安全要求.第2部分:真空泵 |
(Compressors and vacuum pumps, safety requirements - Part 2: Vacuum pumps; German version EN 1012-2:1996) |
| DIN EN 10120-1997 |
焊接过的气罐用薄钢板和钢带 |
(Steel sheet and strip for welded gas cylinders; German version EN 10120:1996) |
| DIN EN 10126-1996 |
非最终退火装态下非合金钢制冷轧电工钢片和钢带 |
(Cold rolled electrical non-alloyed steel sheet and strip delivered in the semi-processed state; German version EN 10126:1995) |
| DIN EN 1013-1-1998 |
单层屋顶用反光成型塑料板.第1部分:一般要求和试验方法 |
(Light transmitting profiled plastic sheeting for single skin roofing - Part 1: General requirements and test methods; German version EN 1013-1:1997) |
| DIN EN 1013-2-1999 |
单层屋顶用反光成型塑料板.第2部分:玻璃纤维增强聚酯树脂板(GF-UP)的特殊要求和检验方法 |
(Light transmitting profiled plastic sheeting for single skin roofing - Part 2: Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP); German version EN 1013-2:1998) |
| DIN EN 1013-3-1998 |
单层屋顶用反光成型塑料板.第3部分:聚氯乙烯(PVC)板的特殊要求和试验方法 |
(Light transmitting profiled plastic sheeting for single skin roofing - Part 3: Specific requirements and test methods for sheets of polyvinyl chloride (PVC); German version EN 1013-3:1997) |
| DIN EN 1013-4-2000 |
单层屋顶用反光成型塑料薄板.第4部分:聚碳酸酯(PC)薄板的特殊要求、试验方法和性能 |
(Light transmitting profiled plastic sheeting for single skin roofing - Part 4: Specific requirements, test methods and performance of polycarbonate (PC) sheets; German version EN 1013-4:2000) |
| DIN EN 1013-5-2000 |
单层屋顶用反光成型塑料薄板.第5部分:聚甲基丙烯酸甲酯(PMMA)薄板的特殊要求、试验方法和性能 |
(Light transmitting profiled plastic sheeting for single skin roofing - Part 5: Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets; German version EN 1013-5:2000) |
| DIN EN 10130-1999 |
用于冷变形的低碳钢冷轧板.交货技术条件(包括修正件A1:1998) |
(Cold rolled low carbon steel flat products for cold forming - Technical delivery conditions (includes amendment A1:1998); German version EN 10130:1991 + A1:1998) |
| DIN EN 10131-1992 |
冷成形用冷轧无涂层低碳钢和高屈服极限的普通钢的扁平制品.尺寸和形状公差 |
(Cold-rolled uncoated low carbon and high-yield strength steel flats for cold forming; tolerances on size and geometrical tolerances; german version EN 10131:1991) |
| DIN EN 10132-1-2000 |
热处理用冷轧窄钢带材.技术提交条件.第1部分:一般 |
(Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 1: General; German version EN 10132-1:2000) |
| DIN EN 10132-2-2000 |
热处理用冷轧窄钢带材.技术提交条件.第2部分:表面硬化钢 |
(Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 2: Case hardening steels; German version EN 10132-2:2000) |
| DIN EN 10132-3-2000 |
热处理用冷轧窄钢带材.技术提交条件.第3部分:淬火和回火 |
(Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 3: Steels for quenching and tempering; German version EN 10132-3:2000) |
| DIN EN 10132-4-2003 |
热处理用冷轧窄钢带材.技术交货条件.第4部分:弹簧钢和其它用途钢 |
(Cold-rolled narrow steel strip for heat-treatment - Technical delivery conditions - Part 4: Spring steels and other applications; German version EN 10132-4:2000 + AC:2002) |
| DIN EN 10136-1990 |
黑色金属材料的化学分析.钢中镍的测定.火焰原子吸收分光光度测定法 |
(Chemical analysis of ferrous materials; determination of nickel in steel and iron; flame atomic absorption spectrometric method) |
| DIN EN 10137-1-1995 |
淬火和回火或沉淀硬化状态下高屈服强度结构钢制板材和宽扁钢.第1部分:一般交货条件 |
(Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - Part 1: General delivery conditions; German version EN 10137-1:1995) |
| DIN EN 10137-2-1995 |
淬火和回火或沉淀硬化状态下高屈服强度结构钢制板材和宽扁钢.第2部分:淬火和回火钢的交换条件 |
(Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - Part 2: Delivery conditions for quenched and tempered steels; German version EN 10137-2:1995) |
| DIN EN 10137-3-1995 |
淬火和回火或沉淀硬化状态下高屈服强度结构钢制板材和宽扁钢.第3部分:沉淀硬化钢的交换条件 |
(Plates and wide flats made of high yield strenght structural steels in the quenched and tempered or precipitation hardened conditions - Part 3: Delivery conditions for precipitation hardened steels; German version EN 10137-3:1995) |
| DIN EN 10139-1997 |
冷成型加工用无涂层低碳钢制冷轧窄钢带.技术交货条件 |
(Cold rolled uncoated mild steel narrow steel strip for cold forming - Technical delivery conditions; German version EN 10139:1997) |
| DIN EN 1014-1-1995 |
木材防腐剂.沥青浸渍油以及用该油的浸渍木材.取样和分析.第1部分:沥青浸渍油取样法 |
(Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Part 1: Procedure for sampling creosote; German version EN 1014-1:1995) |
| DIN EN 1014-2-1996 |
木材防腐剂.沥青浸渍油以及用该油的浸渍木材.取样和分析.第2部分:跟踪分析用从浸渍木材中提取沥青浸渍油试 |
(Wood preservatives - Creosote and creosoted timber; methods for sampling and analysis - Part 2: Procedure for obtaining a sample of creosote from creosoted timber for subsequent analysis; German version EN 1014-2:1995) |
| DIN EN 1014-3-1997 |
木材防腐剂.沥青浸渍油以及用该油浸渍的木材.取样和分析方法.第3部分:杂酚油中苯芬花含量的测定 |
(Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Part 3: Determination of the benzo[a]pyrene content of creosote; German version EN 1014-3:1997) |
| DIN EN 1014-4-1995 |
木材防腐剂.煤焦浸渍油及用该油浸渍的木材.取样和分析.第4部分:煤焦浸渍油中水解萃取苯酚含量的测定 |
(Wood preservatives - Creosote and creosoted timber; methods for sampling and analysis - Part 4: Determination of the water-extractable phenols content of creosote; German version EN 1014-4:1995) |
| DIN EN 10140-1996 |
冷轧窄钢带.尺寸和形状公差 |
(Cold rolled narrow steel strip - Tolerances on dimensions and shape; German version EN 10140:1996) |
| DIN EN 10142-2000 |
冷加工用连续热浸镀锌低碳钢带材和薄板.交货技术条件 |
(Continuously hot-dip zinc coated low carbon steel strip and sheet for cold forming - Technical delivery conditions; German version EN 10142:2000) |
| DIN EN 10143-1993 |
连续热镀钢板和钢带.极根尺寸和形状公差 |
(Continuously hot-dip metal coated steel sheet and strip; tolerances on dimensions and shape; german version EN 10143:1993) |
| DIN EN 10147-2000 |
连续热浸镀锌结构钢带材和薄板.交货技术条件 |
(Continuously hot-dip zinc coated structural steel strip and sheet - Technical delivery conditions; German version EN 10147:2000) |
| DIN EN 10149-1-1995 |
冷成型用高屈服点钢制热轧扁平产品.第1部分:一般交货条件 |
(Hot rolled flat products made of high yield strength steels for cold forming - Part 1: General delivery conditions; German version EN 10149-1:1995) |
| DIN EN 10149-2-1995 |
冷成型用高屈服点钢制热轧扁平产品.第2部分:热机械轧制钢的交货条件 |
(Hot rolled flat products made of high yield strength steels for cold forming - Part 2: Delivery conditions for thermomechanically rolled steels; German version EN 10149-2:1995) |
| DIN EN 10149-3-1995 |
冷成型用高屈服点钢制热轧扁平产品.第3部分:普通退火和轧制钢交货条件 |
(Hot rolled flat products made of high yield strength steels for cold forming - Part 3: Delivery conditions for normalized or normalized rolled steels; German version EN 10149-3:1995) |
| DIN EN 1015-1-1998 |
圬工用灰浆的检验方法.第1部分:用筛分分析测定粒度分布 |
(Methods of test for mortar for masonry - Part 1: Determination of particle size distribution (by sieve analysis); German version EN 1015-1:1998) |
| DIN EN 1015-10-1999 |
圬工用灰浆的检验方法.第10部分:固体灰浆干燥体密度的测定 |
(Methods of test for mortar for masonry - Part 10: Determination of bulk density of hardened mortar; German version EN 1015-10:1999) |
| DIN EN 1015-11-1999 |
圬工用灰浆的检验方法.第11部分:固体灰浆的弯曲拉伸强度和抗压强度的测定 |
(Methods of test for mortar for masonry - Part 11: Determination of flexural and compressive strength of hardened mortar; German version EN 1015-11:1999) |
| DIN EN 1015-12-2000 |
圬工用灰浆的试验方法.第12部分:在基底物上硬化打底和涂抹灰浆的粘结强度的测定 |
(Methods of test for mortar for masonry - Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates; German version EN 1015-12:2000) |
| DIN EN 1015-17-2000 |
圬工用灰浆的试验方法.第17部分:新凝灰浆中水溶性氯化物含量的测定 |
(Methods of test for mortar for masonry - Part 17: Determination of water-soluble chloride content of fresh mortars; German version of EN 1015-17:2000) |
| DIN EN 1015-17-2005 |
圬工用灰浆的试验方法.第17部分:新凝灰浆中水溶性氯化物含量的测定 |
|
| DIN EN 1015-18-2003 |
圬工用灰浆的检验方法.第18部分:测定硬化泥浆毛吸作用引起的水吸收系 |
(Methods of test for mortar for masonry - Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar; German version EN 1015-18:2002) |
| DIN EN 1015-19-1998 |
圬工用灰浆的检验方法.第19部分:粉刷灰浆制固定灰浆的水蒸气渗透性的测定 |
(Methods of test for mortar for masonry - Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars; German version EN 1015-19:1998) |
| DIN EN 1015-19-2005 |
砖石灰浆试验方法.第19部分:硬化初涂灰浆和抹灰灰浆水蒸气渗透性的测定 |
|
| DIN EN 1015-2-1998 |
圬工用灰浆的检验方法.第2部分:灰浆的取样和检验灰浆的制备 |
(Methods of test for mortar for masonry - Part 2: Bulk sampling of mortars and preparation of test mortars; German version EN 1015-2:1998) |
| DIN EN 1015-21-2003 |
圬工用灰浆的检验方法.第21部分:测定底层灰浆与基材的兼容性 |
(Methods of test for mortar for masonry - Part 21: Determination of the compatibility of one-coat rendering mortars with substrates; German version EN 1015-21:2002) |
| DIN EN 1015-3-1999 |
圬工用灰浆的检验方法.第3部分:新鲜灰浆稠度的测定(流动扩展) |
(Methods of test for mortar for masonry - Part 3: Determination of consistence of fresh mortar (by flow table); German version EN 1015-3:1999) |
| DIN EN 1015-3-2004 |
圬工灰浆的试验方法.第3部分:根据流量表测定新凝砂浆的稠度 |
|
| DIN EN 1015-4-1998 |
圬工用灰浆的检验方法.第4部分:用渗透器测定新鲜灰浆的粘度 |
(Methods of test for mortar for masonry - Part 4: Determination of consistence of fresh mortar (by plunger penetration); German version EN 1015-4:1998) |
| DIN EN 1015-6-1998 |
圬工用灰浆的检验方法.第6部分:测定新鲜灰浆的粗密度 |
(Methods of test for mortar for masonry - Part 6: Determination of bulk density of fresh mortar; German version EN 1015-6:1998) |
| DIN EN 1015-7-1998 |
圬工用灰浆的检验方法.第6部分:测定新鲜灰浆的粗密度 |
(Methods of test for mortar for masonry - Part 7: Determination of air content of fresh mortar; German version EN 1015-7:1998) |
| DIN EN 1015-9-1999 |
圬工用灰浆的检验方法.第9部分:新鲜灰浆的可处理时间和可修正时间的测定 |
(Methods of test for mortar for masonry - Part 9: Determination of workable life and correction time of fresh mortar; German version EN 1015-9:1999) |
| DIN EN 10152-1993 |
电解镀锌冷轧扁钢制品.交货技术条件 |
(Electrolytically zinc coated cold rolled steel flat products; technical delivery conditions; German version EN 10152:1993) |
| DIN EN 10152-2003 |
电解镀锌冷轧扁钢制品.交货技术条件 |
(Electrolytically zinc coated cold rolled steel flat products - Technical delivery conditions; German version EN 10152:2003) |
| DIN EN 10154-2002 |
连续热浸镀调质铝硅涂层(AS)钢带和薄板.交货技术条件 |
(Continuously hot-dip aluminium-silicon (AS) coated steel strip and sheet - Technical delivery conditions; German version EN 10154:2002) |
| DIN EN 10155-1993 |
增强的耐大气腐蚀结构钢.交货技术条件 |
(Structural steels with improved atmospheric corrosion resistance; technical delivery conditions; German version EN 10155:1993) |
| DIN EN 10160-1999 |
厚度大于或等于6毫米的钢板制品的超声波检验(平面反射法) |
(Ultrasonic testing of steel flat product of thickness equal to or greater than 6 mm (reflection method); German version EN 10160:1999) |
| DIN EN 10163-1-1991 |
热轧钢制品表面状态的供货条件(薄板.宽扁钢和异型钢).第1部分:一般要求 |
(Technical delivery conditions for the surface condition of hot rolled steel plate, wide flats and sections; general requirements; german version EN 10163-1:1991) |
| DIN EN 10163-2-1991 |
热轧钢制品表面状态的供货条件(薄板.宽扁钢和异型钢).第2部分:薄板和宽扁钢 |
(Technical delivery conditions for the surface condition of hot rolled steel plate, wide flats and sections; plate and wide flats; german version EN 10163-2:1991) |
| DIN EN 10163-3-1991 |
热轧钢制品表面状态的供货条件(薄板.宽扁钢和异型钢).第3部分:异型钢 |
(Technical delivery conditions for the surface condition of hot rolled steel plate, wide flats and sections; part 3: sections; german version EN 10163-3:1991) |
| DIN EN 10164-1993 |
经调质垂直于制品表在变形性能的钢制品.交货技术条件 |
(Steel products with improved deformation properties perpendicular to the surface of the product; technical delivery conditions; German version of EN 10164:1993) |
| DIN EN 10165-1996 |
非最终退火装态下合金钢制冷轧电工钢片和钢带 |
(Cold rolled electrical alloyed steel sheet and strip delivered in the semi-processed state; German version EN 10165:1995) |
| DIN EN 10168-2004 |
钢产品.检验文件.内容和说明的目录表 |
|
| DIN EN 10169-1-1996 |
连续有机涂层(带涂层)的钢板制品.第1部分:概述(定义,材料,极限偏差,试验法) |
(Continuously organic coated (coil coated) steel flat products - Part 1: General information(definitions, materials, tolerances, test methods); German version EN 10169-1:1996) |
| DIN EN 10169-1-2004 |
连续有机涂覆(盘绕涂覆)的扁钢制品.第1部分:一般信息(定义、材料、公差和试验方法) |
|
| DIN EN 1017-1998 |
用于制备饮用水的产品.半烧结的白云石 |
(Chemicals used for treatment of water intended for human consumption - Half-burnt dolomite; German version EN 1017:1998) |
| DIN EN 10177-1990 |
铁材料的化学分析.钢中钙的测定.火焰原子吸收分光光度测定法 |
(Chemical analysis of ferrous materials; determination of calcium in steels; flame atomic absorption spectrometric method; german version EN 10177:1989) |
| DIN EN 10178-1990 |
冶炼材料的化学分析.钢材中铌含量的测定.光度法 |
(Chemical analysis of ferrous materials; determination of niobium in steels; spectrophotometric method; german version EN 10178:1989) |
| DIN EN 10179-1990 |
黑色金属材料的化学分析.钢中氮(微含量)的测定.光度法 |
(Chemical analysis of ferrous materials; determination of nitrogen (trace amounts) in steels; spectrophotometric method) |
| DIN EN 1018-1998 |
用于制备饮用水的产品.碳酸钙 |
(Chemicals used for treatment of water intended for human consumption - Calcium carbonate; German version EN 1018:1998) |
| DIN EN 10181-1990 |
黑色金属材料的化学分析.钢中铅含量)的测定.火焰原子吸收分光光度测定法 |
(Chemical analysis of ferrous materials; determination of lead in steels; flame atomic absorption spectrometric method) |
| DIN EN 10184-1990 |
钢铁材料的化学分析.钢内和铁内磷的测定.分光光度法 |
(Chemical analysis of ferrous materials; determination of phosphorus in steels and irons; spectrophotometric method (including Corrigendum AC:1991)) |
| DIN EN 10188-1990 |
黑色金属材料的化学分析.钢铁中铬的测定.火焰原子吸收分光光度测定法 |
(Chemical analysis of ferrous materials; determination of chromium in steels and iron; flame atomic absorption spectrometric method) |
| DIN EN 1019-1995 |
人员用水的化学处理.二氧化硫 |
(Chemicals used for treatment of water intended for human consumption - Sulfur dioxide; German version EN 1019:1995) |
| DIN EN 1020-2002 |
有风扇支持燃烧气体和/或燃烧物质传输、净热输入功率不超过300kW的空间加热用非家用燃气式强制对流空气加热 |
(Non-domestic gas-fired forced convection air heaters for space heating not exceeding a net heat input of 300 kW, incorporating a fan to assist transportation of combustion air and/or combustion products (includes Amendment A1:2001); German version EN 102 |
| DIN EN 10200-1992 |
钢铁冶炼材料的化学分析.钢中硼含量的测定.分光光度法 |
(Chemical analysis of ferrous materials; determination of boron in steel; spectrophotometric method; german version EN 10200:1991) |
| DIN EN 10202-2001 |
冷轧锡产品.电解锡板和电解铬/氧化铬涂层钢 |
(Cold reduced tinmill products - Electrolytic tinplate and electrolytic chromium/chromium oxide coated steel; German version EN 10202:2001) |
| DIN EN 10204-1995 |
冶金产品.检验文件型式 |
(Metallic products - Types of inspection documents (includes Amendment A1:1995); German version EN 10204:1991 + A1:1995) |
| DIN EN 10204-2005 |
冶金产品.检验文件的类型 |
|
| DIN EN 10205-1992 |
生产白铁皮和电镀铬钢板用冷轧薄钢板卷 |
(Cold reduced blackplate in coil form for the production of tinplate or electrolytic chromium/chromium oxide coated steel; german version EN 10205:1991) |
| DIN EN 10207-1997 |
简单的压力容器用钢材.薄钢板,带钢和棒钢的交货技术条件 |
(Steels for simple pressure vessels - Technical delivery requirements for plates, strips and bars (includes Amendment A1:1997); German version EN 10207:1991 + A1:1997) |
| DIN EN 10207-2005 |
简单压力容器用钢.钢板、带材和棒材的交货技术条件 |
|
| DIN EN 10208-1-1998 |
易燃液体或气体用管道钢管.交货技术条件.第1部分:要求等级为A的管 |
(Steel pipes for pipe lines for combustible fluids - Technical delivery conditions - Part 1: Pipes of requirement class A; German version EN 10208-1:1997) |
| DIN EN 10208-2-1996 |
易燃液体或气体用管道钢管.交货技术条件.第2部分:要求等级为B的管 |
(Steel pipes for pipelines for combustible fluids - Technical delivery conditions - Part 2: Pipes of requirements class B; German version EN 10208-2:1996) |
| DIN EN 10209-1996 |
涂釉低碳钢制冷轧扁平制品.交货技术条件 |
(Cold rolled low carbon steel flat products for vitrious enamelling - Technical delivery conditions; German version EN 10209:1996) |
| DIN EN 1021-1-1994 |
家具.装璜家具易燃性的评估.第1部分:火源:燃着的香烟 |
(Furniture; assessment of the ignitability of upholstered furniture; part 1: ignition source: smouldering cigarette (ISO 8191-1:1987, modified); German version EN 1021-1:1993) |
| DIN EN 1021-2-1994 |
家具.室内装璜家具易燃性的评估.第2部分:火源:等同于火柴的煤气火焰 |
(Furniture; assessment of the ignitability of upholstered furniture; part 2: ignition source: match flame equivalent (ISO 8191-2:1988, modified); German version EN 1021-2:1993) |
| DIN EN 10210-1-1994 |
非合金结构钢和精粒结构钢制的钢构件用热成型空心型件.第1部分:交货技术要求 |
(Hot finished structural hollow sections of non-alloy and fine grain structural steels - Part 1: Technical delivery requirements; German version EN 10210-1:1994) |
| DIN EN 10210-2-1997 |
非合金和细晶粒结构钢的热精加工结构空心型材.第2部分:公差,尺寸和分段特性 |
(Hot finished structural hollow sections of non-alloy and fine grain structural steels - Part 2: Tolerances, dimensions and sectional properties; German version EN 10210-2:1997) |
| DIN EN 10211-1996 |
钢铁材料的化学分析.钢和铁中钛含量测定.火焰原子吸收光谱测定法 |
(Chemical analysis of ferrous materials - Determination of titanium in steel and iron - Flame atomic absorption spectrometric method; German version EN 10211:1995) |
| DIN EN 10212-1995 |
生铁材料的化学分析.用分光光度法测定钢和铁中的砷含量 |
(Chemical analysis of ferrous materials - Determination of arsenic in steel and iron - Spectrophotometric method; German version EN 10212:1995) |
| DIN EN 10213-1-1996 |
压力容器用铸钢的交货技术条件.第1部分:概述 |
(Technical delivery conditions for steel castings for pressure purposes - Part 1: General; German version EN 10213-1:1995) |
| DIN EN 10213-2-1996 |
压力容器用铸钢的交货技术条件.第2部分:室温和高温下使用的钢种 |
(Technical delivery conditions for steel castings for pressure purposes - Part 2: Steel grades for use at room temperature and elevated temperatures; German version EN 10213-2:1995) |
| DIN EN 10213-3-1996 |
压力容器用铸钢的交货技术条件.第3部分:低温下使用的钢种 |
(Technical delivery conditions for steel castings for pressure purposes - Part 3: Steel grades for use at low temperatures; German version EN 10213-3:1995) |
| DIN EN 10213-4-1996 |
压力容器用铸钢的交货技术条件.第4部分:奥氏体和奥氏体铁素钢种 |
(Technical delivery conditions for steel castings for pressure purposes - Part 4: Austenitic and austenitic-ferritic steel grades; German version EN 10213-4:1995) |
| DIN EN 10214-1995 |
连续热浸镀调质带锌铝覆层的钢带和薄板.交货技术条件 |
(Continuously hot-dip zinc-aluminium (ZA) coated steel strip and sheet - Technical delivery conditions; German version EN 10214:1995) |
| DIN EN 10215-1995 |
连续热浸镀调质带铝锌覆层的钢带和薄板.交货技术条件 |
(Continuously hot-dip aluminium-zinc (AZ) coated steel strip and sheet - Technical delivery conditions; German version EN 10215:1995) |
| DIN EN 10216-1-2002 |
压力载荷用无缝钢管.交货技术条件.第1部分:特定室温特性的非合金钢管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties; German version EN 10216-1:2002) |
| DIN EN 10216-1-2004 |
压力载荷用无缝钢管.交货技术条件.第1部分:特定室温特性的非合金钢管 |
|
| DIN EN 10216-2-2002 |
压力载荷用无缝钢管.交货技术条件.第2部分:具有较高温度下规定性能的非合金和合金钢管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steel tubes with specified elevated temperature properties; German version EN 10216-2:2002) |
| DIN EN 10216-2-2004 |
压力载荷用无缝钢管.交货技术条件.第2部分:带特定高温性能的非合金和合金钢管 |
|
| DIN EN 10216-3-2002 |
压力载荷用无缝钢管.交货技术条件.第3部分:细粒合金钢管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 3: Alloy fine grain steel tubes; German version EN 10216-3:2002) |
| DIN EN 10216-3-2004 |
压力载荷用无缝钢管.交货技术条件.第3部分:合金细粒钢管 |
|
| DIN EN 10216-4-2002 |
压力载荷用无缝钢管.交货技术条件.第4部分:有低温特性的非合金和合金钢管 |
(Seamless steel tubes for pressure purposes - Technical delivery conditions - Part 4: Non-alloy and alloy steel tubes with specified low temperature properties; German version EN 10216-4:2002) |
| DIN EN 10216-4-2004 |
压力载荷用无缝钢管.交货技术条件.第4部分:带特定低温性能的非合金和合金钢管 |
|
| DIN EN 10216-5-2004 |
压力用途无缝钢管.交货技术条件.第5部分:不锈钢管 |
|
| DIN EN 10217-1-2002 |
压力载荷用焊接钢管.交货技术条件.第1部分:具有室温下规定性能的非合金钢管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Part 1: Non-alloy steel tubes with specified room temperature properties; German version EN 10217-1:2002) |
| DIN EN 10217-2-2002 |
压力载荷用焊接钢管.交货技术条件.第2部分:具有较高温度下规定性能的电焊非合金和合金钢管 |
(Welded steel tubes for pressure purposes - Technical delivery conditions - Part 2: Electric welded non-alloy and alloy steel tubes with specified elevated temperature properties; German version EN 10217-2:2002) |
5分钟获取标准报价 咨询电话：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com