标准号 |
中文名称 |
英文名称 |
BS EN 60371-3-4-1996 |
云母基绝缘材料规范.第3部分:单项材料规范.第4活页:用B级环氧树脂粘合剂粘结的聚酯薄膜衬底云母纸 |
(Specification for insulating materials based on mica - Specifications for individual materials - Polyester film-backed mica paper with a B-stage epoxy resin binder) |
BS EN 60371-3-5-1996 |
云母基绝缘材料规范.第3部分:单项材料规范.第5活页:用环氧树脂粘合剂粘结的待浸渍处理的玻璃纤维织物衬底云 |
(Specification for insulating materials based on mica - Specifications for individual materials - Glass-backed mica paper with an epoxy resin binder for post-impregnation (VPI)) |
BS EN 60371-3-6-1996 |
云母基绝缘材料规范.第3部分:单项材料规范.第6活页:用B级环氧树脂粘合剂粘结的玻璃纤维织物衬底云母纸 |
(Specification for insulating materials based on mica - Specifications for individual materials - Glass-backed mica paper with a B-stage epoxy resin binder) |
BS EN 60371-3-7-1996 |
云母基绝缘材料规范.第3部分:单项材料规范.单个导体胶带用带有环氧树脂粘结剂的聚脂薄膜云母纸 |
(Specification for insulating materials based on mica - Specifications for individual materials - Polyester film mica paper with an epoxy resin binder for single conductor taping) |
BS EN 60371-3-8-1996 |
云母绝缘材料基规范.第3部分:单项材料规范.第8活页:耐燃烧安全电缆用云母纸带 |
(Specification for insulating materials based on mica - Specifications for individual materials - Mica paper tapes for flame-resistant security cables) |
BS EN 60371-3-9-1996 |
云母基绝缘材料规范.单项材料规范.云母形状 |
(Specification for insulating materials based on mica - Specifications for individual materials - Moulding micanite) |
BS EN 60372-2004 |
绝缘子串件的球窝联接器用锁紧装置.尺寸和试验 |
|
BS EN 60375-2004 |
关于电路和磁路的规定 |
|
BS EN 60379-2004 |
家用电热水器性能测量方法 |
|
BS EN 60382-1993 |
过程控制系统用模拟气动信号 |
(Analogue pneumatic signal for process control systems) |
BS EN 60383-1-1998 |
标称电压1000V以上的架空线用绝缘子.交流系统用陶瓷或玻璃绝缘子装置.定义、试验方法和验收规范 |
(Insulators for overhead lines with a nominal voltage above 1000 V. Ceramic or glass insulator units for a.c. systems - Definitions, test methods and acceptance criteria) |
BS EN 60383-2-1995 |
公称电压高于1000V的架空线路用绝缘子.第2部分:交流电路系统绝缘子串和绝缘子装置.试验方法和验收指标 |
(Insulators for overhead lines with a nominal voltage above 1000 V. Insulator strings and insulator sets for a.c. systems - Definitions, test methods and acceptance criteria) |
BS EN 60384-1-2001 |
用于电气设备的固定电容器.通用规范 |
(Fixed capacitors for use in electronic equipment - Generic specification) |
BS EN 60384-20-1-1999 |
用于电气设备的固定电容器.空白详细规范:固定金属化聚苯撑硫化膜镀层表面固定直流电容器.补充级EZ |
(Fixed capacitors for use in electronic equipment - Blank detail specification: fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors - Assessment level EZ) |
BS EN 60384-20-1999 |
用于电气设备的固定电容器.分规范:固定金属化聚苯撑硫化膜镀层表面固定直流电容器 |
(Fixed capacitors for use in electronic equipment - Sectional specification: fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors) |
BS EN 60384-21-1-2005 |
电子设备用固定电容器.空白详细规范.1级陶瓷介质的表面安装多层固定电容器.评定等级EZ |
|
BS EN 60384-22-1-2005 |
电子设备用固定电容器.空白详细规范.2级陶瓷介质的表面安装多层固定电容器.评定等级EZ |
|
BS EN 60384-22-2005 |
电子设备用固定电容器.分规范.2级陶瓷介质的表面安装多层固定电容器 |
|
BS EN 60387-1993 |
交流电表的符号规范 |
(Specification for symbols for alternating-current electricity meters) |
BS EN 60398-1999 |
工业电热装置.通用试验方法 |
(Industrial electroheating installations - General test methods) |
BS EN 60399-1994 |
带环形底座的E14和E27灯座用圆桶尾端螺纹用标准薄板 |
(Standard sheets for barrel thread for E14 and E27 lampholders with shade holder ring) |
BS EN 60399-2004 |
带灯罩卡环的灯座的圆筒螺纹 |
|
BS EN 604-1-1997 |
铝及铝合金.铸锻件坯.检查和交付的技术规范 |
(Aluminium and aluminium alloys - Cast forging stock - Technical conditions for inspection and delivery) |
BS EN 604-2-1997 |
铝及铝合金.铸锻件坯.尺寸和形状公差 |
(Aluminium and aluminium alloys - Cast forging stock - Tolerances on dimensions and form) |
BS EN 60400-2000 |
管形荧光灯和启动器座用灯座 |
(Lampholders for tubular fluorescent lamps and starterholders) |
BS EN 60401-1-2005 |
铁氧体软磁芯的术语和命名.物理不规则性术语 |
|
BS EN 60401-2-2003 |
铁氧体软磁芯的术语和命名.尺寸参考 |
(Terms and nomenclature for cores made of magnetically soft ferrites - Reference of dimensions) |
BS EN 60401-3-2004 |
磁性软铁氧体制磁芯的术语和命名.写入变压器和电感器磁芯制造厂产品目录中的数据格式指南 |
|
BS EN 60404-14-2002 |
磁性材料.用拔出或旋转法对铁磁材料试样的磁偶极矩的测量方法 |
(Magnetic materials - Methods of measurement of the magnetic dipole moment of a ferromagnetic material specimen by the withdrawal or rotation method) |
BS EN 60404-2-1996 |
磁性材料.爱普斯坦框架法测量电钢薄板和带材的磁性能 |
(Magnetic materials - Methods of measurement of the magnetic properties of electrical steel sheet and strip by means of an Epstein frame.) |
BS EN 60404-4-1997 |
磁性材料.钢铁直流磁性能的测量方法 |
(Magnetic materials - Methods of measurement of d.c. magnetic properties of iron and steel) |
BS EN 60404-6-2003 |
磁性材料.使用环形样品测量磁性软金属及粉末材料在20Hz至200kHz频率范围内磁特性的方法 |
(Magnetic materials - Methods of measurement of the magnetic properties of magnetically soft metallic and powder materials at frequencies in the range 20 Hz to 200 kHz by the use of ring specimens) |
BS EN 60406-1997 |
X射线医疗诊断用X射线摄影盒式磁带和乳腺X射线摄影盒式磁带 |
(Specification for radiographic cassettes and mammographic cassettes used for medical X-ray diagnosis) |
BS EN 60417-1-1999 |
设备使用的图形符号.概述和应用 |
(Graphical symbols for use on equipment - Overview and application) |
BS EN 60417-2-1999 |
设备用图形符号.符号原图 |
(Graphical symbols for use on equipment - Symbol originals) |
BS EN 60420-1991 |
高压交流电路开关保险联接的规范 |
(Specification for high-voltage alternating current switch-fuse combinations) |
BS EN 60423-1995 |
电气设备用导管.电气安装用导管的外径和导管及配件的螺纹 |
(Conduits for electrical purposes - Outside diameters of conduits for electrical installations and threads for conduits and fittings) |
BS EN 60424-1-2000 |
铁氧体磁芯表面缺陷的限值指南.通用规范 |
(Guidance of the limits of surface irregularities of ferrite cores - General specification) |
BS EN 60424-2-1998 |
铁氧体磁芯表面不平度极限值的导则.RM-磁芯 |
(Guidance of the limits of surface irregularities of ferrite cores - RM-cores) |
BS EN 60424-3-1999 |
铁氧体磁芯表面缺陷的限值指南.ETD芯和E芯 |
(Guidance of the limits of surface irregularities of ferrite cores - ETD-cores and E-cores) |
BS EN 60424-4-2001 |
铁氧体磁芯表面缺陷极限值的导则.环形磁芯 |
(Guidance of the limits of surface irregularities of ferrite cores - Ring cores) |
BS EN 60427-2001 |
高压交流断路器的合成试验 |
(Synthetic testing of high-voltage alternating current circuit-breakers) |
BS EN 60431-1984 |
磁性氧化物正方形磁芯(RM磁芯)及其相关部件的尺寸规范 |
(Specification for dimensions of square cores (RM-cores) made of magnetic oxides and associated parts) |
BS EN 60432-1-2000 |
白炽灯安全规范.家用和类似普通照明用钨丝灯 |
(Safety specification for incandescent lamps - Tungsten filament lamps for domestic and similar general lighting purposes) |
BS EN 60432-2-2000 |
白炽灯安全规范.家用和类似普通照明用卤钨灯 |
(Safety specification for incandescent lamps - Tungsten halogen lamps for domestic and similar general lighting purposes) |
BS EN 60432-3-2003 |
白炽灯安全规范.卤钨灯(非车用) |
(Safety specification for incandescent lamps - Tungsten-halogen lamps (non-vehicle)) |
BS EN 60433-1999 |
额定电压高于1KW的架空线绝缘子.交流系统陶瓷绝缘子.长棍型绝缘单特性 |
(Insulators for overhead lines with a nominal voltage above 1 kV - Ceramic insulators with a.c. systems - Characteristics of insulator units of the long rod type) |
BS EN 60437-1998 |
高电压绝缘子无线电干扰试验 |
(Radio interference test on high-voltage insulators) |
BS EN 60439-1-1999 |
低压开关设备和控制设备组件规范.经过型式试验和部分型式试验的组件 |
(Specification for low-voltage switchgear and controlgear assemblies - Type-tested and partially type-tested assemblies) |
BS EN 60439-2-2000 |
低压开关设备和控制设备组件规范.母线线槽系统(汇流条通道)的特殊要求 |
(Specification for low-voltage switchgear and controlgear assemblies - Particular requirements for busbar trunking systems (busways)) |
BS EN 60439-3-1991 |
低压开关和控制设备组件规范.安装在技术不熟练人员可以使用他们的地方的低压开关和控制设备组件的特殊要求. |
(Specification for low-voltage switchgear and controlgear assemblies - Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled p) |
BS EN 60439-4-1991 |
低压开关和控制设备组件规范.第4部分:施工现场用组件的特殊要求 |
(Specification for low-voltage switchgear and controlgear assemblies - Particular requirements for assemblies for construction sites (ACS)) |
BS EN 60439-4-2005 |
低压开关设备和控制设备组件.施工现场用组件的特殊要求(ACS) |
|
BS EN 60439-5-1996 |
低压开关设备和控制设备组件.第5部分:室外公共场所安装用组件的特殊要求.网络电力分配用电缆交接箱 |
(Specification for low-voltage switchgear and controlgear assemblies - Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for) |
BS EN 60442-1999 |
家用和类似目的的电烤箱.性能测量方法 |
(Electric toasters for household and similar purposes - Methods for measuring the performance) |
BS EN 60444-2-1993 |
石英晶体单参数的测定.第2部分:用相位偏离法测量石英晶体单的动态电容 |
(Measurement of quartz crystal unit parameters - Phase offset method for measurement of motional capacitance of quartz crystal units) |
BS EN 60444-3-1993 |
石英晶体单参数的测定.第3部分:用与并联电容量Co补偿相连的π网络相位技术测量200MHz以下的石英谐振器的 |
(Measurement of quartz crystal unit parameters - Basic method for the measurement of two-terminal parameters of quartz crystal units up to 200 MHz by phase technique in a) |
BS EN 60444-4-1993 |
石英晶体单参数的测量.第4部分:30MHz以下石英晶体件负荷谐振频率fL.负荷谐振电阻R1的测量方法,以及石英 |
(Measurement of quartz crystal unit parameters - Method for the measurement of the load resonance frequency fDOWNL, load resonance resistance RDOWNL and the calculation of other derived values of quart) |
BS EN 60444-5-1995 |
石英晶体单参数测量.第5部分:用自动网络分析仪和误差修正技术评定电气参数的测量方法 |
(Measurement of quartz crystal unit parameters - Methods for the determination of equivalent electrical parameters using automatic network analyzer techniques and error correction) |
BS EN 60444-6-1995 |
石英晶体单参数的测量.驱动级相关性的测量 |
(Measurement of quartz crystal unit parameters - Measurement of drive level dependence (DLD)) |
BS EN 60444-7-2004 |
石英晶体件参数的测量.石英晶体件的活性和频率下降的测量 |
|
BS EN 60444-8-2003 |
石英晶体件参数的测量.表面安装石英晶体件用试验装置 |
(Measurement of quartz crystal unit parameters - Test fixture for surface mounted quartz crystal units) |
BS EN 60445-2000 |
人机接口、标记与识别的基本与安全原则.电器端子和用相应符号标志的接线端子的识别方法(包括字母数字标志识 |
(Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals and of terminations of certain designated conductors, including general rules) |
BS EN 60446-2000 |
人机界面标记和识别的基础和安全原理.用颜色或数字对导体的识别 |
(Basic and safety principles for man-machine interface, marking and identification - Identification of conductors by colours or numerals) |
BS EN 60447-1994 |
人机联系装置(MMI).起动性能 |
(Man-machine interface (MMI) - Actuating principles) |
BS EN 60447-2004 |
人机接口、标记和识别的基本和安全总则.工作总则 |
|
BS EN 60450-2004 |
新旧纤维素电绝缘材料聚合的平均粘度测量 |
|
BS EN 60454-1-1995 |
电工用压敏粘带规范.一般要求 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - General requirements) |
BS EN 60454-2-1995 |
电工用压敏粘带规范.试验方法 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Methods of test) |
BS EN 60454-3-1-1998 |
电工用压敏粘带规范.单项材料规范.带有压敏胶的PVC薄膜胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - PVC film tapes with pressure-sensitive adhesive) |
BS EN 60454-3-10-1996 |
电工用压敏粘带规范.单项材料规范.带有橡胶热固性胶的乙酸丁酸纤维素薄膜胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Requirements for cellulose-acetate-butyrate film tapes with rubber thermosettin) |
BS EN 60454-3-11-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.有橡胶热固胶粘剂的乙酸纤维素织物纤维带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Combination tapes made of creped cellulosic paper and polyethylene terephthalat) |
BS EN 60454-3-12-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.有压力敏感胶粘剂的聚乙烯膜带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyethylene film tapes with pressure-sensitive adhesive) |
BS EN 60454-3-13-1996 |
电工用压敏粘带规范.单项材料规范.一侧涂覆热塑材料、另一侧带有橡胶热固性胶的结合纤维素胶粘编织带的要求 |
() |
BS EN 60454-3-14-2002 |
电工用压敏粘带规范.单项材料规范.涂压敏粘剂的聚四氟乙烯薄膜带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polytetrafluoroethylene film tapes with pressure-sensitive adhesive.) |
BS EN 60454-3-15-2002 |
电工用压敏粘带规范.单项材料规范.涂橡胶热固性粘胶剂的聚酯膜/聚酯非编织复合物 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyester film/polyester non-woven combinations with rubber thermosetting adhes) |
BS EN 60454-3-16-2003 |
电工用压敏胶粘带规范.单项材料规范.涂压敏粘合剂的聚酯薄膜/玻璃长丝复合带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyester film/glass filament combinations with pressure-sensitive adhesive) |
BS EN 60454-3-17-2002 |
电工用压敏粘带规范.单项材料规范.涂压敏粘胶剂的聚酯/环氧树脂复合物 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyester/epoxy combinations with pressure-sensitive adhesive) |
BS EN 60454-3-18-2003 |
电工用压敏胶粘带规范.单项材料规范.涂压敏粘合剂的聚丙烯薄膜胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polypropylene film tapes with pressure-sensitive adhesive) |
BS EN 60454-3-19-2003 |
电工用压敏胶粘带.单项材料规范.两面涂压敏粘合剂的各种衬料制胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Tapes made from various backing materials with pressure-sensitive adhesive on b) |
BS EN 60454-3-2-1998 |
电工用压敏粘带规范.单项材料规范.带有橡胶热固胶或丙烯酸交联胶的聚酯薄膜胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyester film tapes with rubber thermosetting or acrylic crosslinked adhesives) |
BS EN 60454-3-3-1998 |
电工用压敏粘带规范.单一材料规范.带有橡胶热塑胶粘剂的聚酯薄膜带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyester film tapes with rubber thermoplastic adhesive) |
BS EN 60454-3-4-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.纤维素纸,皱纹.橡胶,热固胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Cellulosic paper, creped, with rubber thermosetting adhesive) |
BS EN 60454-3-5-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.纤维素纸,非皱纹.橡胶,热固胶粘带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Cellulosic paper, non-creped, with rubber thermosetting adhesive) |
BS EN 60454-3-6-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.带丙烯酸类树脂热塑胶粘剂的聚碳酸酯膜带. |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polycarbonate film tapes with acrylic thermoplastic adhesive) |
BS EN 60454-3-7-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.有压力敏感胶粘剂的聚酰亚胺膜带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Polyimide film tapes with pressure-sensitive adhesive) |
BS EN 60454-3-8-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.有压力敏感胶粘剂的玻璃纤维 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Glass fabric with pressure-sensitive adhesive) |
BS EN 60454-3-9-1998 |
电气用途的压力敏感胶粘带规范.单独材料规范.有橡胶热固胶粘剂的乙酸纤维素织物纤维带 |
(Specifications for pressure-sensitive adhesive tapes for electrical purposes - Specifications for individual materials - Cellulose acetate woven fabric tapes with rubber thermosetting adhesive) |
BS EN 60455-1-1998 |
用于电气绝缘的树脂基电抗复合物.定义和一般要求 |
(Resin based reactive compounds used for electrical insulation - Definitions and general requirements) |
BS EN 60455-2-1999 |
用于电气绝缘的树脂基电抗复合物.试验方法 |
(Resin based reactive compounds used for electrical insulation - Methods of test) |
BS EN 60455-3-1-2003 |
电气绝缘用树脂基反应性复合物.单项材料规范.未加填料的环氧树脂复合物 |
(Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Unfilled epoxy resinous compounds) |
BS EN 60455-3-2-2003 |
电气绝缘用树脂基反应性复合物.单项材料规范.填石英的环氧树脂复合物 |
(Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Quartz filled epoxy resinous compounds) |
BS EN 60455-3-3-2003 |
电气绝缘用树脂基反应性复合物.单项材料规范.未加填料的聚氨酯复合物 |
(Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Unfilled polyurethane compounds) |
BS EN 60455-3-4-2003 |
电气绝缘用树脂基反应性复合物.单项材料规范.加填料的聚氨酯复合物 |
(Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Filled polyurethane compounds) |
BS EN 60455-3-5-2002 |
电气绝缘用树脂基活性化合物.单项材料规范.不饱和聚酯浸渍树脂 |
(Resin based reactive compounds used for electrical insulation - Specifications for individual materials - Unsaturated polyester based impregnating resins) |
BS EN 60456-1999 |
家用电动洗衣机.性能测量方法 |
(Clothes washing machines for household use - Methods for measuring the performance) |
BS EN 60456-2005 |
家用洗衣机.性能测量方法 |
|
BS EN 60461-2001 |
录像机的时间和控制规则 |
(Time and control code for video tape recorders) |
BS EN 60464-1-1999 |
用于电气绝缘的清漆.定义和一般要求 |
(Varnishes used for electrical insulation - Definitions and general requirements) |
BS EN 60464-2-2001 |
用于电气绝缘的清漆.试验方法 |
(Varnishes used for electrical insulation - Methods of test) |
BS EN 60464-3-1-2002 |
电绝缘漆.单项材料规范.室温固化覆盖漆 |
(Varnishes used for electrical insulation - Specifications for individual materials - Ambient curing finishing varnishes) |
BS EN 60464-3-2-2002 |
电绝缘漆.单项材料规范.热固化浸渍漆 |
(Varnishes used for electrical insulation - Specifications for individual materials - Hot curing impregnating varnishes) |
BS EN 60465-1992 |
缆索用带油导管的未使用过的绝缘矿物油 |
(Specification for unused insulating mineral oils for cables with oil ducts) |
BS EN 60470-2001 |
高压交流接触器和基于接触器的电动机起动器 |
(High-voltage alternating current contactors and contactor-based motor starters) |
BS EN 60480-2005 |
从电气设备中取出六氟化硫(SF6)的检验和处理指南及其再使用规范 |
|
BS EN 60491-1997 |
摄影用电子闪光设备的安全要求 |
(Safety requirements for electronic flash apparatus for photographic purposes) |
BS EN 60495-1994 |
单边带供电线载波端子 |
(Single sideband power-line carrier terminals) |
BS EN 60503-1998 |
广播磁带录像机用卷筒 |
(Spools for broadcast videotape recorders (VTRS)) |
BS EN 60505-2000 |
电绝缘系统的评价和合格鉴定 |
(Evaluation and qualification of electrical insulation systems) |
BS EN 60507-1993 |
交流系统使用的高压绝缘子人工污染试验 |
(Artificial pollution tests on high-voltage insulators to be used on a.c. systems) |
BS EN 60510-2-5-1996 |
卫星地面站用无线电设备的测量方法.第2部分:分系统的测量.第5节:调频器 |
(Methods of measurement for radio equipment used in satellite earth stations - Measurements for sub-systems - Frequency modulators) |
BS EN 60510-2-6-1996 |
卫星地面站用无线电设备的测量方法.分系统的测量.频率解调器 |
(Methods of measurement for radio equipment used in satellite earth stations - Measurements for sub-systems - Frequency demodulators) |
BS EN 60510-3-4-1996 |
卫星地面站用无线电设备的测量方法.第3部分:分系统组合件的测量方法.第4节:分频多路传输 |
(Methods of measurement for radio equipment used in satellite earth stations - Methods of measurement on combinations of sub-systems - Measurements for frequency division multiplex (f.d.m.) transmissio) |
BS EN 60512-1-100-2001 |
电子设备用机电件.基本试验程序和测量方法.总则.应用出版物 |
(Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - General - General - Applicable publications) |
BS EN 60512-1-2-2002 |
电子设备用机电件.基本试验程序和测量方法.总则.试验1b.尺寸和质量的检验 |
(Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - General - Test 1b - Examination of dimension and mass) |
BS EN 60512-1-2001 |
电子设备用机电件.基本试验规程和测量方法.总则 |
(Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - General) |
BS EN 60512-1-3-1997 |
电子设备用机电组件.基本试验过程和测量方法.常规.试验1c.电接合长度 |
(Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - General - Test 1c - Electrical engagement length) |
BS EN 60512-1-4-1997 |
电子设备机电组件.基本试验过程和测量方法.常规.试验1d.接触防护有效性 |
(Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - General - Test 1d - Contact protection effectiveness (scoop-proof)) |
BS EN 60512-10-4-2003 |
电子设备用连接器.试验和测量.试验10d:连接器电过负荷 |
(Connectors for electronic equipment - Tests and measurements - Test 10d - Electrical overload (connectors)) |
BS EN 60512-11-1-1999 |
电气设备的电机件.基本试验过程和测量方法.气候试验.试验11a.气候结果 |
(Electromechanical components for electronic equipment - Basic testing procedures and measuring methods - Climatic tests - Test 11a - Climatic sequence) |