标准号 |
中文名称 |
英文名称 |
EN 12255-10-2000 |
废水处理厂第10部分:安全规则 |
Wastewater treatment plants - Part 10: Safety principles |
EN 12255-11-2001 |
废水处理厂第11部分:一般要求的数据 |
Wastewater treatment plants - Part 11: General data required |
EN 12255-12-2003 |
废水处理厂第12部分:控制和自动化 |
Wastewater treatment plants - Part 12: Control and automation |
EN 12255-13-2002 |
废水处理厂第13部分:化学处理 通过沉淀/絮凝作用除理废水 |
Wastewater treatment plants - Part 13: Chemical treatment; Treatment of wastewater by precipitation/flocculation |
EN 12255-4-2002 |
废水处理厂第4部分:初级沉降 |
Wastewater treatment plants - Part 4: Primary settlement |
EN 12255-5-1999 |
废水处理厂第5部分:沉淀池处理 |
Wastewater treatment plants - Part 5: Lagooning processes |
EN 12255-6-2002 |
废水处理厂第6部分:活性污泥处理 |
Wastewater treatment plants - Part 6: Activated sludge process |
EN 12255-7-2002 |
废水处理厂第7部分:生物固定膜反应器 |
Wastewater treatment plants - Part 7: Biological fixed-film reactors |
EN 12255-8-2001 |
废水处理厂第8部分: 污泥处理和存贮 |
Wastewater treatment plants - Part 8: Sludge treatment and storage |
EN 12255-9-2002 |
废水处理厂第9部分:气味控制和通风 |
Wastewater treatment plants - Part 9: Odour control and ventilation |
EN 12256-1998 |
塑料管道系统.热塑性塑料配件装配式配件机械强度或挠度的试验方法 |
Plastics piping systems - Thermoplastics fittings - Test method for mechanical strength or flexibility of fabricated fittings |
EN 12257-2002 |
可移动气瓶无缝、环裹复合气瓶 |
Transportable gas cylinders - Seamless, hoop-wrapped composite cylinders |
EN 12258-1-1998 |
铝和铝合金术语和定义第1部分:通用术语 |
Aluminium and aluminium alloys - Terms and definitions - Part 1: General terms |
EN 12258-3-2003 |
铝和铝合金术语和定义第3部分:废料 |
Aluminium and aluminium alloys - Terms and definitions - Part 3: Scrap |
EN 12259-2-1999 |
固定消防系统喷水器和喷水系统构件第2部分:湿式报警阀组件 |
Fixed firefighting systems - Components for sprinkler and water spray systems - Part 2: Wet alarm valve assemblies |
EN 12259-5-2002 |
固定消防系统喷水器和喷水系统构件第5部分:水流检测器 |
Fixed firefighting systems - Components for sprinkler and water spray systems - Part 5: Water flow detectors |
EN 1226-1996 |
塑料管道系统 玻璃增强热固性塑料管 验证初期环状物挠曲阻力的试验方法 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Test method to prove the resistance to initial ring deflection |
EN 12260-2003 |
标准号: |
中文标题: |
EN 12262-1998 |
旋动式泵技术文件术语、输出范围、设计 |
Rotodynamic pumps - Technical documents - Terms, delivery range, layout |
EN 12263-1998 |
制冷系统和加热泵限压安全开关装置要求和试验 |
Refrigerating systems and heat pumps - Safety switching devices for limiting the pressure - Requirements and tests |
EN 12266-1-2003 |
工业阀门阀门试验第1部分:压力试验、试验程序和验收标准、强制要求 |
Industrial valves - Testing of valves - Part 1: Pressure tests, test procedures and acceptance criteria; Mandatory requirements |
EN 12266-2-2002 |
工业阀门阀门试验第2部分:试验、试验程序和验收标准 补充要求 |
Industrial valves - Testing of valves - Part 2: Tests, test procedures and acceptance criteria; Supplementary requirements |
EN 12267-2003 |
食品加工机械圆锯床安全和卫生要求 |
Food processing machinery - Circular saw machines - Safety and hygiene requirements |
EN 12268-2003 |
食品加工机械带锯床安全和卫生要求 |
Food processing machinery - Band saw machines - Safety and hygiene requirements |
EN 12269-1-2000 |
用“压梁试验”测定钢筋与热压加气混凝土之间的粘结性能第1部分:短期试验 |
Determination of the bond behaviour between reinforcing steel and autoclaved aerated concrete by the beam test - Part 1: Short term test |
EN 1227-1997 |
塑料管道系统 玻璃增强热固性塑料管 潮湿条件下长期最终相关环状物挠曲的测定 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the long-term ultimate relative ring deflection under wet conditions |
EN 12270-1998 |
登山设备楔子安全要求和试验方法 |
Mountaineering equipment - Chocks - Safety requirements and test methods |
EN 12271-3-2002 |
地面修整规范第3部分:粘合剂和碎屑扩散速度和扩散准确度 |
Surface dressing - Specifications - Part 3: Rate of spread and accuracy of spread of binders and chippings |
EN 12272-1-2002 |
地面修整试验方法第1部分:粘合剂和碎屑扩散速度和扩散准确度 |
Surface dressing - Test methods - Part 1: Rate of spread and accuracy of spread of binders and chippings |
EN 12272-2-2003 |
表面覆盖层试验方法第2部分:缺陷目测 |
Surface dressing - Test methods - Part 2: Visual assessment of defects |
EN 12272-3-2003 |
地面修整试验方法第3部分:采用Vialit板冲击试验法测定粘合剂集料粘结性 |
Surface dressing - Test method - Part 3: Determination of binder aggregate adhesivity by the Vialit plate shock test method |
EN 12274-1-2002 |
泥浆表面处理试验方法第1部分:粘合剂萃取物取样 |
Slurry surfacing - Test methods - Part 1: Sampling for binder extraction |
EN 12274-2-2003 |
泥浆表面处理试验方法第2部分:残留粘合剂含量的测定 |
Slurry surfacing - Test methods - Part 2: Determination of residual binder content |
EN 12274-3-2002 |
泥浆表面处理试验方法第3部分:一致性 |
Slurry surfacing - Test methods - Part 3: Consistency |
EN 12274-4-2003 |
泥浆表面处理试验方法第4部分:混合物粘性的测定 |
Slurry surfacing - Test methods - Part 4: Determination of cohesion of the mix |
EN 12274-5-2003 |
泥浆表面处理试验方法第5部分:耐磨性的测定 |
Slurry surfacing - Test method - Part 5: Determination of wearing |
EN 12274-6-2002 |
泥浆表面处理试验方法第6部分:使用率 |
Slurry surfacing - Test methods - Part 6: Rate of application |
EN 12275-1998 |
登山设备连接器安全要求和试验方法 |
Mountaineering equipment - Connectors - Safety requirements and test methods |
EN 12277-1998 |
登山设备吊带安全要求和试验方法 |
Mountaineering equipment - Harnesses - Safety requirements and test methods |
EN 12278-1998 |
登山设备滑轮安全要求和试验方法 |
Mountaineering equipment - Pulleys - Safety requirements and test methods |
EN 12279-2000 |
供气系统供气线路上的气压调节装置功能要求 |
Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements |
EN 1228-1996 |
塑料管道系统 玻璃增强热固性塑料管 初始特定环刚度的测定 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness |
EN 12280-1-1997 |
橡胶或塑料涂覆织物加速老化试验第1部分:热老化 |
Rubber- or plastics-coated fabrics - Accelerated ageing tests - Part 1: Heat ageing |
EN 12280-2-2002 |
橡胶或塑料涂覆织物加速老化试验第2部分: 自然老化:光的影响或风化 |
Rubber- or plastics-coated fabrics - Accelerated ageing tests - Part 2: Physical ageing: effect of light or weathering |
EN 12280-3-2002 |
橡胶或塑料涂覆织物加速老化试验第3部分:环境老化 |
Rubber- or plastics-coated fabrics - Accelerated ageing tests - Part 3: Environmental ageing |
EN 12281-2002 |
打印和商务用纸干性上色剂成像法所用复印纸的要求 |
Printing and business paper - Requirements for copy paper for dry toner imaging processes |
EN 12283-2002 |
打印和商务用纸上色剂附着力的测定 |
Printing and business paper - Determination of toner adhesion |
EN 12284-2003 |
制冷系统和加热泵阀门要求、试验和标志 |
Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
EN 12285-1-2003 |
工厂预制钢罐第1部分:易燃和不易燃的水污染液体地下储存用卧式圆柱形单层和双层钢罐 |
Workshop fabricated steel tanks - Part 1: Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and non-flammable water polluting liquids |
EN 12287-1999 |
体外诊断医疗器械生物起源样品中数量的测量标准物质描述 |
In vitro diagnostic medical devices - Measurement of quantities in samples of biological origin - Description of reference materials |
EN 12288-2003 |
工业用阀 铜合金闸阀 |
Industrial valves - Copper alloy gate valves |
EN 1229-1996 |
塑料管道系统 玻璃增强热固性塑料管 验证短期内部压力下墙的密封性试验方法 |
Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure |
EN 12291-2003 |
高级工艺业陶瓷大气压下的空气环境中陶瓷合成物的高温机械特性压缩特性的测定 |
Advanced technical ceramics - Mechanical properties of ceramic composites at high temperature in air at atmosphere pressure - Determination of compression properties |
EN 12293-1999 |
塑料管道系统热水和冷水用热塑性塑料管道和接头安装组件耐热循环性的试验方法 |
Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling |
EN 12294-1999 |
塑料管道系统热水和冷水系统真空下气密性的试验方法 |
Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum |
EN 12295-1999 |
塑料管道系统热水和冷水用热塑性塑料管道和接头接合处耐压力循环试验方法 |
Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling |
EN 12296-1998 |
生物技术设备清洁能力试验程序指南 |
Biotechnology - Equipment - Guidance on testing procedures for cleanability |
EN 12297-1998 |
生物技术设备灭菌能力试验程序指南 |
Biotechnology - Equipment - Guidance on testing procedures for sterilizability |
EN 12298-1998 |
生物技术设备气密性试验程序指南 |
Biotechnology - Equipment - Guidance on testing procedures for leaktightness |
EN 1230-1-2001 |
与食品接触的纸和板 感官分析 第1部分:气味 |
Paper and board intended for contact with foodstuffs - Sensory analysis - Part 1: Odour |
EN 12300-1998 |
低温容器低温设备的清洁度 |
Cryogenic vessels - Cleanliness for cryogenic service |
EN 12301-2000 |
橡胶和塑料机械砑光机安全要求 |
Rubber and plastics machines - Calenders - Safety requirements |
EN 12302-2000 |
原焦油和粗苯术语 |
Crude tar and crude benzole - Terminology |
EN 12303-2000 |
煤焦油机油 术语 |
Coal tar based oils - Terminology |
EN 12305-1997 |
生物技术用于环境中的变性有机物遗传变性植物审慎释放用取样策略指南 |
Biotechnology - Modified organisms for application in the environment - Guidance for the sampling strategies for deliberate releases of genetically modified plants |
EN 12306-1997 |
生物技术农业、植物和动物病虫害控制和环境污染中使用的诊断盒质量控制指南 |
Biotechnology - Guidance for quality control of diagnostic kits used in agriculture, plant and animal pest and disease control and environmental contamination |
EN 12307-1997 |
生物技术规模加工和生产良好习惯、程序、人员培训和管理指南 |
Biotechnology - Large-scale process and production - Guidance for good practice, procedures, training and control for personnel |
EN 12308-1998 |
液化天然装置和设备液化天然气管道中所用的法兰接头垫圈设计适配性试验 |
Installations and equipment for LNG - Suitability testing of gaskets designed for flanged joints used on LNG piping |
EN 12309-1-1999 |
净热输入不超过70kW的燃气吸热和吸热式空调和/或加热泵装置第1部分:安全性 |
Gas-fired absorption and adsorption air-conditioning and/or heat pump appliances with a net heat input not exceeding 70 kW - Part 1: Safety |
EN 12309-2-2000 |
净热输入不超过70kW的燃气吸热和吸热式空调和/或加热泵装置第2部分:能量的合理使用 |
Gas-fired absorption and adsorption air-conditioning and/or heat pump appliances with a net heat input not exceeding 70 kW - Part 2: Rational use of energy |
EN 1231-1996 |
工作场所空气 短期检测管测量系统 要求和试验方法 |
Workplace atmospheres - Short term detector tube measurement systems - Requirements and test methods |
EN 12310-1-1999 |
挠性防水板第1部分:屋面防水沥青板抗裂性测定(钉杆) |
Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of resistance to tearing (nail shank) |
EN 12310-2-2000 |
挠性防水板抗性测定第2部分:塑料和橡胶屋面防水板 |
Flexible sheets for waterproofing - Determination of resistance to tearing - Part 2: Plastic and rubber sheets for roof waterproofing |
EN 12311-1-1999 |
挠性防水板第1部分:.屋面防水沥青板拉伸性能的测定 |
Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of tensile properties |
EN 12311-2-2000 |
挠性防水板拉伸性能的测定第2部分:塑料和橡胶屋面防水板 |
Flexible sheets for waterproofing - Determination of tensile properties - Part 2: Plastic and rubber sheets for roof waterproofing |
EN 12312-1-2001 |
航空地面辅助设备特殊要求第1部分:旅客用梯 |
Aircraft ground support equipment - Specific requirements - Part 1: Passenger stairs |
EN 12312-12-2002 |
航空地面辅助设备特殊要求第12部分:便携式供水设备 |
Aircraft ground support equipment - Specific requirements - Part 12: Potable water service equipment |
EN 12312-13-2002 |
航空地面辅助设备特殊要求第13部分:盥洗设备 |
Aircraft ground support equipment - Specific requirements - Part 13: Lavatory service equipment |
EN 12312-17-2004 |
飞行器地面支持设备.特殊要求.第17部分:空调设备 |
|
EN 12312-2-2002 |
航空地面辅助设备备特殊要求第2部分:给养车 |
Aircraft ground support equipment - Specific requirements - Part 2: Catering vehicles |
EN 12312-3-2003 |
航空地面辅助设备特殊要求第3部分:传送带车 |
Aircraft ground support equipment - Specific requirements - Part 3: Conveyor belt vehicles |
EN 12312-4-2003 |
航空地面辅助设备特殊要求第4部分:旅客登机桥 |
Aircraft ground support equipment - Specific requirements - Part 4: Passenger boarding bridges |
EN 12312-6-2004 |
飞行器地面支持设备.特殊要求.第6部分:去冰机和除冰/防冻设备 |
|
EN 12316-1-1999 |
挠性防水板第1部分:沥青屋面防水板结合处抗裂性的测定 |
Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of peel resistance of joints |
EN 12316-2-2000 |
挠性防水板结合处抗裂性的测定第2部分:塑料和橡胶屋面防水板 |
Flexible sheets for waterproofing - Determination of peel resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing |
EN 12317-1-1999 |
挠性防水板第1部分:屋面防水沥青板结合处抗剪切性的测定 |
Flexible sheets for waterproofing - Part 1: Bitumen sheets for roof waterproofing - Determination of shear resistance of joints |
EN 12317-2-2000 |
挠性防水板结合处抗剪切性的测定第2部分:塑料和橡胶屋面防水板 |
Flexible sheets for waterproofing - Determination of shear resistance of joints - Part 2: Plastic and rubber sheets for roof waterproofing |
EN 1232-1997 |
工作场所空气 化学试剂的个人抽样用泵 要求和试验方法 |
Workplace atmospheres - Pumps for personal sampling of chemical agents - Requirements and test methods |
EN 12320-2001 |
建筑五金件挂锁和挂锁配件要求和试验方法 |
Building hardware - Padlocks and padlock fittings - Requirements and test methods |
EN 12321-2003 |
地下采矿机械铠装刮板运输机安全要求规范 |
Underground mining machinery - Specification for the safety requirements of armoured scraper conveyors |
EN 12323-1998 |
条码符号学规范“16K码” |
Bar coding - Symbology specifications - Code 16K |
EN 12324-1-1998 |
灌溉技术轮机系统第1部分:尺寸系列 |
Irrigation techniques - Reel machine systems - Part 1: Size series |
EN 12324-2-1999 |
灌溉技术轮机系统第2部分:轮机用聚乙烯管规范 |
Irrigation techniques - Reel machine systems - Part 2: Specifications of polyethylene tubes for reel machines |
EN 12324-3-1999 |
灌溉技术轮机系统第3部分:技术特性表述 |
Irrigation techniques - Reel machine systems - Part 3: Presentation of technical characteristics |
EN 12324-4-1999 |
灌溉技术轮机系统第4部分:用户要求核对表 |
Irrigation techniques - Reel machine systems - Part 4: Check list of users requirements |
EN 12325-1-1998 |
灌溉技术中心枢轴和横移系统第1部分:技术特性的描述 |
Irrigation techniques - Centre pivot and moving lateral systems - Part 1: Presentation of the technical characteristics |
EN 12325-2-1999 |
灌溉技术中心枢轴和横移系统第2部分:最低性能和技术特性 |
Irrigation techniques - Centre pivot and moving lateral systems - Part 2: Minimum performances and technical characteristics |
EN 12325-3-1999 |
灌溉技术中心枢轴和横移系统第3部分:术语和分类 |
Irrigation techniques - Centre pivot and moving lateral systems - Part 3: Terminology and classification |
EN 12326-1-2004 |
不连续屋顶材料和覆面用石板和石材.第1部分:产品规范 |
|
EN 12326-2-2000 |
不连续屋顶及覆盖层用石板和石材第2部分:试验方法 |
Slate and stone products for discontinuous roofing and cladding - Part 2: Methods of test |
EN 12326-2-2004 |
搭接屋顶材料和覆面用石板和石材.第2部分:试验方法 |
|
EN 12327-2000 |
供气系统压力试验、试运转和非试运转程序功能要求 |
Gas supply systems - Pressure testing, commissioning and decommissioning procedures - Functional requirements |
EN 12329-2000 |
金属防腐铁或钢上带辅助处理的锌电镀层 |
Corrosion protection of metals - Electrodeposited coatings of zinc with supplementary treatment on iron or steel |
EN 1233-1996 |
水质 铬测定 原子吸收光谱测定法 |
Water quality - Determination of chromium - Atomic absorption spectrometric methods |
EN 12330-2000 |
金属防腐铁或钢上的镉电镀层 |
Corrosion protection of metals - Electrodeposited coatings of cadmium on iron or steel |
EN 12332-1-1998 |
橡胶或塑料涂覆织物脆裂强度的测定第1部分:钢球法 |
Rubber or plastic coated fabrics - Determination of bursting strength - Part 1: Steel ball method |
EN 12332-2-2002 |
橡胶或塑料涂覆织物脆裂强度的测定第2部分:静压法 |
Rubber- or plastic-coated fabrics - Determination of bursting strength - Part 2: Hydraulic method |
EN 12334-2001 |
工业阀门铸铁止回阀 |
Industrial valves - Cast iron check valves |
EN 12334-2004 |
工业阀门.铸铁控制阀门 |
|
EN 12337-1-2000 |
建筑物玻璃化学加强碱石灰硅酸盐玻璃第1部分:定义和描述 |
Glass in building - Chemically strengthened soda lime silicate glass - Part 1: Definition and description |
EN 12337-2-2004 |
建筑物用玻璃.化学增强钠钙安全玻璃.第2部分:合格评价/产品标准 |
|
EN 12338-1998 |
水质汞的测定汞齐化浓缩法 |
Water quality - Determination of mercury - Enrichment methods by amalgamation |
EN 12339-1997 |
内河航运船舶绳索槽 |
Inland navigation vessels - Rope tubs |
EN 123400-800-1992 |
能力详细规范无贯通连接的挠性印制板 |
Capability detail specification;Flexible printed boards without through connections |
EN 123400/prA1-1993 |
分规范:无贯通连接的挠性印制板修改prA1 |
Sectional specification: flexible printed boards without through connections; amendments |
EN 12341-1998 |
空气质量悬浮颗粒物PM10系数的测定标准方法和验证测量方法标准等效性的现场试验程序 |
Air quality - Determination of the PM10 fraction of suspended particulate matter - Reference method and field test procedure to demonstrate reference equivalence of measurement methods |
EN 12342-1998 |
配合麻醉装置和通风器使用的呼吸管 |
Breathing tubes intended for use with anaesthetic apparatus and ventilators |
EN 12345-1998 |
焊接带图示的有关焊接接头的多语种术语 |
Welding - Multilingual terms for welded joints with illustrations |
EN 12346-1998 |
体操器械肋木、格梯和爬架安全要求和试验方法 |
Gymnastic equipment - Wall bars, lattice ladders and climbing frames - Safety requirements and test methods |
EN 12347-1998 |
生物技术蒸汽灭菌器和高压消毒蒸锅的性能标准 |
Biotechnology - Performance criteria for steam sterilizers and autoclaves |