标准号 |
中文名称 |
英文名称 |
BS EN 12270-1998 |
登山设备.轮挡.安全要求和试验方法 |
(Mountaineering equipment - Chocks - Safety requirements and test methods) |
BS EN 12271-3-2002 |
敷路料.规范.粘合剂和石屑摊铺的速度和准确度 |
(Surface dressing - Specifications - Rate of spread and accuracy of spread of binder and chippings) |
BS EN 12272-1-2002 |
敷路料.试验方法.粘合剂和石屑摊铺的速度和准确度 |
(Surface dressing - Test methods - Rate of spread and accuracy of spread of binder and chippings) |
BS EN 12272-2-2004 |
敷路料.试验方法.缺陷的外观评定 |
|
BS EN 12272-2-2004 |
敷路料.试验方法.缺陷的外观评定 |
|
BS EN 12272-3-2003 |
敷路料.试验方法.用Vialit板冲击试验方法测定粘合剂集料的粘着性 |
(Surface dressing - Test methods - Determination of binder aggregate adhesivity by the Vialit plate shock test method) |
BS EN 12274-1-2002 |
泥浆表面修整.试验方法.粘合剂萃取抽样法 |
(Slurry surfacing - Test methods - Sampling for binder extraction) |
BS EN 12274-2-2003 |
敷路料.试验方法.残余粘合剂含量的测定 |
(Slurry surfacing - Test methods - Determination of residual binder content) |
BS EN 12274-3-2002 |
泥浆表面修整.试验方法.一致性 |
(Slurry surfacing - Test methods - Consistency) |
BS EN 12274-4-2003 |
砂浆路面层.试验方法.混合物黏合性的测定 |
(Slurry surfacing - Test methods - Determination of cohesion of the mix) |
BS EN 12274-5-2003 |
砂浆路面层.试验方法.磨损性测定 |
(Slurry surfacing - Test methods - Determination of wearing) |
BS EN 12274-6-2002 |
泥浆表面修整.试验方法.使用率 |
(Slurry surfacing - Test methods - Rate of application) |
BS EN 12275-1998 |
登山设备.连接器.安全要求和试验方法 |
(Mountaineering equipment - Connectors - Safety requirements and test methods) |
BS EN 12276-1999 |
登山设备.摩擦固定器.安全要求和检验方法 |
(Mountaineering equipment - Frictional anchors - Safety requirements and test methods) |
BS EN 12277-1998 |
登山运动器材.挽具.安全要求和试验方法 |
(Mountaineering equipment - Harnesses - Safety requirements and test methods) |
BS EN 12278-1998 |
登山设备.皮带轮.安全要求和试验方法 |
(Mountaineering equipment - Pulleys - Safety requirements and test methods) |
BS EN 12279-2000 |
燃气供应系统.作业线上的气压调节装置.功能要求 |
(Gas supply systems - Gas pressure regulating installations on service lines - Functional requirements) |
BS EN 1228-1997 |
塑料管道系统.玻璃纤维增强热固塑料(GFK).特殊初始环状刚性的测算 |
(Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of initial specific ring stiffness) |
BS EN 12280-1-1998 |
橡胶或塑料涂层织物.加速老化试验.热老化 |
(Rubber- or plastics-coated fabrics - Accelerated ageing tests - Heat ageing) |
BS EN 12280-2-2002 |
橡胶或塑料涂层织物.加速老化试验.物理性老化:光和风化的影响 |
(Rubber- or plastics-coated fabrics - Accelerated ageing tests - Physical ageing: effect of light or weathering) |
BS EN 12280-3-2002 |
橡胶或塑料涂层织物.加速老化试验.物理性老化:环境老化 |
(Rubber- or plastics-coated fabrics - Accelerated ageing tests - Environmental ageing) |
BS EN 12281-2002 |
印刷纸和商务用纸.干调色剂成像工艺用复印纸的要求 |
(Printing and business paper - Requirements for copy paper for dry toner imaging processes) |
BS EN 12283-2002 |
印刷纸和商务用纸.调色剂粘性的测定 |
(Printing and business paper - Determination of toner adhesion) |
BS EN 12284-2003 |
冷却系统和加热泵.阀.要求、试验及标记 |
(Refrigerating systems and heat pumps - Valves - Requirements, testing and marking) |
BS EN 12285-1-2003 |
工厂制造的钢罐.易燃和不易燃的水污染液体地下储存用卧式圆柱形单层和双层钢罐 |
(Workshop fabricated steel tanks - Horizontal cylindrical single skin and double skin tanks for the underground storage of flammable and non-flammable water polluting liquids) |
BS EN 12285-2-2005 |
工厂制造的钢罐.易燃和不易燃的水污染液体地上储存用卧式圆柱形单层和双层钢罐 |
|
BS EN 12286-1999 |
体外诊断的医疗设备.生物有机体试样的数量测量.参考测量过程的介绍 |
(In vitro diagnostic medical devices - Measurement of quantities in samples of biological origin - Presentation of reference measurement procedures) |
BS EN 12287-1999 |
实验室诊断医疗设备.生物起始试样中的数量测量.标准物质的说明 |
(In vitro diagnostic medical devices - Measurement of quantities in samples of biological origin - Description of reference materials) |
BS EN 12288-2003 |
工业用阀.铜合金闸阀 |
(Industrial valves - Copper alloy gate valves) |
BS EN 1229-1997 |
塑料管道系统.玻璃增强热固性塑料管.验证短期内部压力下墙的密封性试验方法 |
(Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods to prove the leaktightness of the wall under short-term internal pressure) |
BS EN 12291-2004 |
高级工业陶瓷.大气压力下高温空气中陶瓷复合材料的机械性能.压缩特性的测定 |
|
BS EN 12291-2004 |
高级工业陶瓷.大气压力下高温空气中陶瓷复合材料的机械性能.压缩特性的测定 |
|
BS EN 12293-2000 |
塑料管道系统.热水和冷水用热塑管和配件.已安装的组件耐温度变化性能的试验方法 |
(Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling) |
BS EN 12294-2000 |
塑料管道系统.热水和冷水系统.真空情况下渗漏性的试验方法 |
(Plastic piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum) |
BS EN 12295-2000 |
塑料管道系统.热水和冷水用热塑管和附属配件.连接件耐压力变化的试验方法 |
(Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling) |
BS EN 12296-1998 |
生物技术.设备.清洁处理试验程序指南 |
(Biotechnology - Equipment - Guidance on testing procedures for cleanability) |
BS EN 12297-1998 |
生物技术.设备.灭菌试验程序指南 |
(Biotechnology - Equipment - Guidance on testing procedures for sterilizability) |
BS EN 12298-1998 |
生物技术.设备.渗漏严密性试验过程指南 |
(Biotechnology - Equipment - Guidance on testing procedures for leaktightness) |
BS EN 1230-1-2002 |
与食品接触的纸和纸板.感官分析.气味 |
(Paper and board intended for contact with foodstuffs - Sensory analysis - Odour) |
BS EN 1230-2-2002 |
与食品接触的纸和纸板.感官分析. 去香味 |
(Paper and board intended for contact with foodstuffs - Sensory analysis - Off-flavour (taint)) |
BS EN 12300-1999 |
低温容器.低温装置清洁性 |
(Cryogenic vessels - Cleanliness for cryogenic service) |
BS EN 123000-1989 |
电子器件质量评定协调体系.总规范:印制电路板 |
(Harmonized system of quality assessment for electronic components - Generic specification: printed boards) |
BS EN 12301-2000 |
橡胶和塑料机械.砑光机.安全要求 |
(Rubber and plastics machines - Calenders - Safety requirements) |
BS EN 12302-2000 |
原焦油和粗苯.术语 |
(Crude tar and crude benzole - Terminology) |
BS EN 12303-2000 |
煤焦油基油.术语 |
(Coal tar based oils - Terminology) |
BS EN 12305-1998 |
生物技术.用于环境中的变异有机物.遗传变异植物审慎释放用取样策略指南 |
(Biotechnology - Modified organisms for application in the environment - Guidance for the sampling strategies for deliberate releases of genetically modified plants) |
BS EN 12306-1998 |
生物技术.农业,植物和动物病虫害控制和环境污染中用的诊断器具的质量控制指南 |
(Biotechnology - Guidance for quality control of diagnostic kits used in agriculture, plant and animal pest and disease control and environmental contamination) |
BS EN 12307-1998 |
生物技术.大比例工艺流程和生产.良好的实际操作和工序,人员的培训和管理的指南 |
(Biotechnology - Large-scale process and production - Guidance for good practice, procedures, training and control for personnel) |
BS EN 12308-1998 |
液化天然器安装和设备.用于液化天然器管道的法兰接头垫圈设计适配性试验 |
(Installations and equipment for LNG - Suitability testing of gaskets designed for flanged joints used on LNG piping) |
BS EN 12309-1-2000 |
净热输入不超过70KW的燃气吸收和吸收空气调湿式和/或热泵装置 |
(Gas-fired absorption and adsorption air-conditioning and/or heat pump appliances with a net heat input not exceeding 70 kW - Safety) |
BS EN 12309-2-2000 |
净热输入不超过70KW的燃气吸收和吸收空气调湿式和/或热泵装置.能量的合理使用 |
(Gas-fired absorption and adsorption air-conditioning and/or heat pump appliances with a net heat input not exceeding 70 kW - Rational use of energy) |
BS EN 1231-1997 |
工作场所空气.短期检测管测量系统.要求和试验方法 |
(Workplace atmospheres - Short term detector tube measurement systems - Requirements and test methods) |
BS EN 12310-1-2000 |
防水柔性板.抗裂性测定(钉杆).屋顶防水沥青板 |
(Flexible sheets for waterproofing - Determination of resistance to tearing (nail shank) - Bitumen sheets for roof waterproofing) |
BS EN 12310-2-2000 |
防水柔性板.抗裂性测定(钉杆).屋顶防水用塑料和橡胶薄板 |
(Flexible sheets for waterproofing - Determination of resistance to tearing (nail shank) - Plastic and rubber sheets for roof waterproofing) |
BS EN 123100-1989 |
电子器件质量评定协调体系.分规范:具有平孔的单边和双边印制电路板 |
(Harmonized system of quality assessment for electronic components: Sectional specification: Single and double sided printed boards with plain holes) |
BS EN 12311-1-2000 |
防水柔性板.拉伸特性测定.屋顶防水沥青板 |
(Flexible sheets for waterproofing - Determination of tensile properties - Bitumen sheets for roof waterproofing) |
BS EN 12311-2-2000 |
防水柔性板.拉伸性能的测定.屋顶防水用塑料和橡胶薄板 |
(Flexible sheets for waterproofing - Determination of tensile properties - Plastic and rubber sheets for roof waterproofing) |
BS EN 12312-1-2001 |
航空器地面支持设备.特殊要求.顾客梯 |
(Aircraft ground support equipment - Specific requirements - Passenger stairs) |
BS EN 12312-11-2005 |
航空器地面支持设备.特殊要求.第11部分:容器/集装箱推车和可拆卸载重拖车 |
|
BS EN 12312-12-2002 |
航空器地面支持设备.特殊要求.饮用水服务设施 |
(Aircraft ground support equipment - Specific requirements - Potable water service equipment) |
BS EN 12312-13-2002 |
航空器地面支持设备.特殊要求.洗浴室服务设施 |
(Aircraft ground support equipment - Specific requirements - Lavatory service equipment) |
BS EN 12312-17-2004 |
航空器地面支持设备.特殊要求.空气调节设备 |
|
BS EN 12312-19-2005 |
飞行器地面支持设备.特殊要求.飞行器千斤顶、轴式千斤顶和液压机尾托架 |
|
BS EN 12312-2-2002 |
航空器地面支持设备.特殊要求.炊事车 |
(Aircraft ground support equipment - Specific requirements - Catering vehicles) |
BS EN 12312-3-2003 |
航空器地面支持设备.特殊要求.输送带式运输装置 |
(Aircraft ground support equipment - Specific requirements - Conveyor belt vehicles) |
BS EN 12312-4-2003 |
航空器地面支持设备.特殊要求.乘客登机桥 |
(Aircraft ground support equipment - Specific requirements - Passenger boarding bridges) |
BS EN 12312-5-2005 |
飞行器地面支持设备.特殊要求.飞行器加油设备 |
|
BS EN 12312-6-2004 |
航空器地面支持设备.特殊要求.去冰和防冻设备 |
|
BS EN 12316-1-2000 |
防水柔性板.接头抗剥离性的测定.屋顶防水沥青板 |
(Flexible sheets for waterproofing - Determination of peel resistance of joints - Bitumen sheets for roof waterproofing) |
BS EN 12316-2-2000 |
防水柔性板.接头抗剥离性的测定.屋顶防水用塑料和橡胶薄板 |
(Flexible sheets for waterproofing - Determination of peel resistance of joints - Plastic and rubber sheets for roof waterproofing) |
BS EN 12317-1-2000 |
防水柔性板.屋顶防水沥青板.接头剪切抗性的测定 |
(Flexible sheets for waterproofing - Bitumen sheets for roof waterproofing - Determination of shear resistance of joints) |
BS EN 12317-2-2000 |
防水柔性板.屋顶防水用塑料和橡胶薄板 |
(Flexible sheets for waterproofing - Plastic and rubber sheets for roof waterproofing) |
BS EN 1232-1997 |
工作场所空气.化学试剂的个人抽样用泵.要求和试验方法 |
(Workplace atmospheres - Pumps for personal sampling of chemical agents - Requirements and test methods) |
BS EN 12320-2001 |
建筑五金.锁和锁配件.要求和试验方法 |
(Building hardware - Padlocks and padlock fittings - Requirements and test methods) |
BS EN 123200-1989 |
电子器件质量评定协调体系.分规范:具有镀通孔的单面和双面印制电路板 |
(Harmonized system of quality assessment for electronic components: Sectional specification: Single and double sided printed boards with plated through holes) |
BS EN 12321-2003 |
地下采矿机械.铠装运输机的安全要求规范 |
(Underground mining machinery - Specification for the safety requirements of armoured face conveyors) |
BS EN 12322-1999 |
实验室诊断医疗装置.微生物用培养基.培养基的性能标准 |
(In vitro diagnostic medical devices - Culture media for microbiology - Performance criteria for culture media) |
BS EN 12323-1998 |
条码.符号规范.“16K码“ |
(Bar coding - Symbology specifications - “Code 16K“) |
BS EN 12323-2005 |
AIDC 技术.符号规范.16K码 |
|
BS EN 12324-1-1999 |
灌溉技术.轮机系统.尺寸系列 |
(Irrigation techniques - Reel machine systems - Size series) |
BS EN 12324-2-1999 |
灌溉技术.轮机系统.轮机用聚乙烯管规范 |
(Irrigation techniques - Reel machine systems - Specifications of polyethylene tubes for reel machines) |
BS EN 12324-3-1999 |
灌溉技术.轮机系统.技术特性的表示 |
(Irrigation techniques - Reel machine systems - Presentation of technical characteristics) |
BS EN 12324-4-1999 |
灌溉技术.轮机系统.用户要求核对表 |
(Irrigation techniques - Reel machine systems - Check list of users requirements) |
BS EN 12325-1-1999 |
灌溉技术.中轴和侧边系统.展示和技术特性 |
(Irrigation techniques - Centre pivot and moving lateral systems - Presentation of the technical characteristics) |
BS EN 12325-2-1999 |
灌溉技术.中轴和移动横向支撑系统.最小性能和技术特性 |
(Irrigation techniques - Centre pivot and moving lateral systems - Minimum performances and technical characteristics) |
BS EN 12325-3-1999 |
灌溉技术.中轴和移动横向支撑系统.术语和分类 |
(Irrigation techniques - Centre pivot and moving lateral systems - Terminology and classification) |
BS EN 12326-1-2004 |
搭接屋顶和覆面用石板和石材.生产规范 |
|
BS EN 12326-1-2004 |
搭接屋顶和覆面用石板和石材.生产规范 |
|
BS EN 12326-2-2000 |
搭接屋顶和覆面用石板和石材.试验方法 |
(Slate and stone products for discontinuous roofing and cladding - Methods of test) |
BS EN 12327-2000 |
燃气供应系统.压力试验,交付使用和非交付使用过程.功能要求 |
(Gas supply systems - Pressure testing, commissioning and decommissioning procedures - Functional requirements) |
BS EN 12329-2000 |
金属的防腐蚀保护.用在铁和钢上补充处理的锌的电解镀层 |
(Corrosion protection of metals - Electrodeposited coatings of zinc with supplementary treatment on iron or steel) |
BS EN 1233-1997 |
水质.铬测定.原子吸收光谱测定法 |
(Water quality - Determination of chromium - Atomic absorption spectrometric methods) |
BS EN 12330-2000 |
金属的腐蚀防护.钢铁上的镉电解镀层 |
(Corrosion protection of metals - Electrodeposited coatings of cadmium on iron or steel) |
BS EN 123300-1989 |
电子器件质量评定协调体系规范.性能分规范:多层印制电路板 |
(Specification for harmonized system of quality assessment for electronic components - Sectional specification - Multilayer printed boards) |
BS EN 12332-1-1999 |
橡胶或塑料涂覆织物.破裂强度的测定.钢球法 |
(Rubber- or plastics-coated fabrics - Determination of bursting strength - Steel ball method) |
BS EN 12332-2-2002 |
橡胶或塑料涂覆织物.抗破碎强度的测定.液压法 |
(Rubber- or plastics-coated fabrics - Determination of bursting strength - Hydraulic method) |
BS EN 12334-2001 |
工业阀门.铸铁单向阀 |
(Industrial valves - Cast iron check valves) |
BS EN 12336-2005 |
隧道掘进机.盾构机、止推钻孔机、螺旋钻探机、衬里安装设备.安全要求 |
|
BS EN 12337-1-2000 |
建筑物用玻璃.化学增强钠钙安全玻璃.定义和描述 |
(Glass in building - Chemically strengthened soda lime silicate glass - Definition and description) |
BS EN 12337-2-2004 |
建筑物用玻璃.化学增强钠钙硅酸盐玻璃.合格评价/产品标准 |
|
BS EN 12337-2-2004 |
建筑物用玻璃.化学增强钠钙安全玻璃.合格评价/产品标准 |
|
BS EN 12338-1998 |
水质.汞的测定.汞齐化增量法 |
(Water quality - Determination of mercury - Enrichment methods by amalgamation) |
BS EN 12339-1997 |
内河航运船舶.绳索槽 |
(Inland navigation vessels - Rope tubs) |
BS EN 123400-1990 |
电子器件质量评定协调体系.分规范.无贯通连接的柔性印制电路板 |
(Harmonized system of quality assessment for electronic components - Sectional specification: flexible printed boards without through connections) |
BS EN 123400-800-1991 |
电子器件质量评定协调体系.性能详细规范:无贯通连接的挠性印制电路板 |
(Harmonized system of quality assessment for electronic components - Capability detail specification: flexible printed boards without through-connections) |
BS EN 12341-1999 |
空气质量.悬浮尘埃中PM10系数的测定.测量步骤和参照测量方法的等值验证用参照法和野外检验法 |
(Air quality - Determination of the PM10 fraction of suspended particulate matter - Reference method and field test procedure to demonstrate reference equivalence of measurement methods) |
BS EN 12342-1998 |
与麻醉装置和通风器一起使用的呼吸用管 |
(Breathing tubes intended for use with anaesthetic apparatus and ventilators) |
BS EN 12345-1999 |
焊接.有图示的焊接接头的多语种术语 |
(Welding - Multilingual terms for welded joints with illustrations) |
BS EN 12346-1999 |
体操器材.球棒,格梯,爬架.安全要求和试验方法 |
(Gymnastic equipment - Wall bars, lattice ladders and climbing frames - Safety requirements and test methods) |
BS EN 12347-1998 |
生物技术.蒸汽灭菌器和高压釜的性能规范 |
(Biotechnology - Performance criteria for steam sterilizers and autoclaves) |
BS EN 12348-2000 |
立式岩心钻机.安全性 |
(Core drilling machines on a stand - Safety) |
BS EN 1235-1995 |
固体肥料.筛分试验 |
(Solid fertilizers - Test sieving) |
BS EN 12350-1-2000 |
新鲜混凝土试验.取样 |
(Testing fresh concrete - Sampling) |
BS EN 12350-2-2000 |
新鲜混凝土试验.坍蹋试验 |
(Testing fresh concrete - Slump test) |
BS EN 12350-3-2000 |
新浇混凝土试验.振动试验 |
(Testing fresh concrete - Vebe test) |
BS EN 12350-4-2000 |
新鲜混凝土试验.兼容程度 |
(Testing fresh concrete - Degree of compactability) |
BS EN 12350-5-2000 |
新鲜混凝土试验.流动台试验 |
(Testing fresh concrete - Flow table test) |
BS EN 12350-6-2000 |
新鲜混凝土试验.密度 |
(Testing fresh concrete - Density) |
BS EN 12350-7-2000 |
新浇混凝土试验.空气含量.压力法 |
(Testing fresh concrete - Air content - Pressure methods) |
BS EN 123500-1990 |
电子器件质量评定协调体系.分规范:带贯通连接的挠性印制电路板 |
(Specification for harmonized system of quality assessment for electronic components - Sectional specification: flexible printed boards with through connections) |