标准号 |
中文名称 |
英文名称 |
| DIN 65516-1984 |
航空和航天.钢制.短螺纹.有内锯齿和MJ螺纹的圆柱头螺钉.温度235℃以下.额定抗拉强度900MPa |
(Aerospace; cheese head bolts with internal serration thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65517-2002 |
航空和航天.温度315℃以下.额定抗拉强度1100MPa的钛合金.短螺纹有内锯齿带MJ螺纹的圆柱头螺钉.温度315℃以 |
(Aerospace - Cheese head bolts, close tolerance, with bihexagon socket and MJ thread, short thread, titanium alloy, nominal tensile strength 1100 MPa, for temperatures up to 315 鳦) |
| DIN 65518-1984 |
航空和航天.钛合金.短螺纹.有肋条平锥头十字槽和MJ螺纹的平头螺钉.温度315℃以下.额定抗拉强度1100MPa |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ-thread, short thread, titanium alloy, nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65519-1984 |
航空和航天.短螺纹.钢制.有肋条平锥头十字槽和MJ螺纹的平头螺钉.温度可达235℃.额定抗拉强度900MPa |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65520-1984 |
航空和航天.短螺纹.钢制.有肋平锥头十字槽和MJ螺纹的平头配合螺钉.温度可达235℃.额定抗拉强度900MPa |
(Aerospace; pan head bolts, close tolerance, with ribbed TORQ-SET (ACR) recess an MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65521-1-1984 |
航空和航天.平锥头十字槽.肋形状.尺寸 |
(Aerospace; TORQ-SET and ACR; dimensions) |
| DIN 65521-2-1984 |
航空与航天.翼形十字槽.装筋板.深度规 |
(Aerospace; TORQ-SET and ACR; penetration gauges) |
| DIN 65521-3-1984 |
航空与航天.翼形十字槽.筋条螺钉旋具尖端 |
(Aerospace; TORQ-SET and ACR; screwdriver points) |
| DIN 65522-1984 |
航空和航天.螺纹接近于头部.不锈钢制.具有MJ螺纹的六角头螺钉.温度可达425℃.额定抗拉强度700MPa |
(Aerospace; screws, hexagon, with MJ-thread, threaded opproximatley to head, corrosion-resisting steel, nominal tensile strength 700 MPa, for temperatures up to 425 C) |
| DIN 65523-1984 |
航空和航天.不锈钢制.短螺纹.具有MJ螺纹的六角头螺钉.温度可达425℃.额定抗拉强度700MPa |
(Aerospace; hexagon bolts, with MJ-thread, short thread, corrosion-resisting steel, nominal tensile strength 700 MPa, for temperatures up to 425 C) |
| DIN 65524-1984 |
航空和航天.钢制.短螺纹.具有MJ螺纹的六角头螺钉.温度可达235℃.额定抗拉强度900MPa |
(Aerospace; heaxagon bolts, with MJ-thread, short thread, steel, nominal tensile strength 900 MPa, for temperatures up to 235 C) |
| DIN 65525-1992 |
航空和航天.带钢制MJ短螺纹的六角螺钉.温度235℃以下额定抗拉强度1100MPa |
(Aerospace; bolts, hexagon, close tolerance, with MJ-thread, short thread, steel, nominal tensile strength 1100 MPa, for temperatures up to 235 C) |
| DIN 65526-1998 |
航空和航天.带MJ螺纹,短螺纹,钛合金钢制六角配合螺钉.温度315℃及其以下用额定抗拉强度1100MPa |
(Aerospace - Hexagon bolts, close tolerance, with short-length MJ thread, titanium alloy - Nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65527-1984 |
航空和航天.短螺纹.钢制.具有MJ螺纹的六角头紧公差螺钉.温度可达235℃.额定抗拉强度1100MPa |
(Aerospace; hexagon bolts, close tolerance, with MJ-thread, short thread, steel, nominal tensile stregth 1100 MPa, for temperatures up to 235 C) |
| DIN 65528-1984 |
航空航天.自锁、钢制带圆柱深沉孔和凸缘的有MJ螺纹的十二角螺母.等级:1550MPa/1800MPa/235℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, steel, class: 1550 MPa/1800 MPa/235 鳦) |
| DIN 65528-2005 |
航空航天系列.钢制自锁紧、带深沉孔、凸缘和MJ螺纹的十二角螺母.等级:1550MPa/1800MPa/235℃ |
|
| DIN 65529-1984 |
航空航天.自锁、钢制带圆柱形深沉孔和凸缘及MJ螺纹的十二角螺母.等级:1250MPa/235℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, steel, class: 1250 MPa/235 鳦) |
| DIN 65529-2005 |
航空航天系列.钢制自锁紧、带深沉孔、凸缘和MJ螺纹的十二角螺母.等级:1250MPa/235℃ |
|
| DIN 65530-1989 |
航空航天.自锁、耐腐蚀钢制、带圆柱形深沉孔和凸紧及MJ螺纹的十二角螺母.等级.1550MPa/315℃/425℃ |
(Aerospace; nuts, bihexagonal, with flange and MJ thread, deep counterbore, self-locking, corrosion-resisting steel, classification: 1550 MPa/315 鳦/425 鳦) |
| DIN 65531-1984 |
航空航天.自锁、耐腐蚀钢制带圆柱形深沉孔和凸紧及MJ螺纹的十二角螺母.等级:1100MPa/1250MPa/315℃/425℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, corrosion-resisting, steel, class: 1100 MPa/1250 MPa/315 鳦/425 鳦) |
| DIN 65531-2005 |
航空航天系列.耐腐蚀钢制自锁紧、带深沉孔、凸缘和MJ螺纹的十二角螺母.等级:1250 MPa/315 鳦/425 鳦 |
|
| DIN 65532-1984 |
航空和航天.螺纹槽符合DINISO5855的MJ螺纹的螺纹末端和螺纹退刀槽 |
(Aerospace; runouts, undercuts and thread ends for MJ-threads to DIN ISO 5855) |
| DIN 65533-1987 |
航空和航天.螺钉和螺母.原材料和配置及表面处理.推荐.选择 |
(Aerospace; bolts, screws and nuts; allocation of materials and surface treatments; recommended selection) |
| DIN 65534-1992 |
航空和航天.带耐蚀钢制MJ螺纹的六角螺母.等级:1100/650℃ |
(Aerospace; nuts, hexagon, with MJ-thread, corrosion resisting steel; classification: 1100 MPa/650 C) |
| DIN 65535-1986 |
航空航天.耐腐蚀钢制带MJ螺纹的自锁螺母同槽组件(螺母板).螺母间距为固定的或选定的.等级:1100MPa/315℃ |
(Aerospace; gang channel nut assembly, with self-locking nuts with MJ thread, nut spacing fixed or optional, in corrosion-resisting steel; class: 1100 MPa/315 鳦) |
| DIN 65536-1-1986 |
航空和航天.铜合金制螺钉锁定的导线螺纹接头.等级:1100MPa/425℃ |
(Aerospace; inserts, helical coil threads, screw-locking, copper alloy; class: 1100 MPa/425 C) |
| DIN 65536-2-1986 |
航空和航天.铜合金制螺钉锁定的导线螺纹接头.安装和工具 |
(Aerospace; inserts, helical coil threads, screw-locking, copper alloy; assembly and special tools) |
| DIN 65537-1987 |
航空和航天.带内齿和MJ螺纹.短螺纹.镍合金制圆柱形螺栓.抗拉强度1250MPa.温度315℃/425℃以下 |
(Aerospace; cheese head bolts with bihexagon socket and MJ thread, short thread, nickel alloy; nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65538-1987 |
航空和航天.带内齿和MJ螺纹.短螺纹.镍合金制圆柱形螺栓.额定抗拉强度1250MPa.温度315℃/425℃以下 |
(Aerospace; cheese head bolts, close tolerance, with bihexagon socket and MJ thread, short thread, nickel alloy; nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65541-1987 |
航空和航天.带筋翼形十字槽和MJ螺纹.螺纹接近头部.镍合金制平头螺栓.额定抗拉强度1250MPa.温度315℃/425℃ |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and MJ thread; fully threaded, nickel alloy; nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65542-1987 |
航空和航天.具有筋翼形十字槽和MJ螺纹.短螺纹.镍合金制埋头配合螺栓.额定抗拉强度1250MPa.温度315℃/425℃ |
(Aerospace; countersunk head screws, close tolerance, with ribbed TORQ-SET (ACR) recess and MJ thread, short thread length, nickel alloy, nominal tensile strength 1250 MPa, for temperatures up to 315 C/425 C) |
| DIN 65546-1985 |
航空航天.带圆柱形深沉孔、带凸紧及MJ螺纹的自锁及耐腐蚀钢十二角螺母.等级:1100MPa/315℃/425℃ |
(Aerospace; nuts, bihexagonal with flange and MJ-thread, deep counterbore, self-locking, corrosion-resisting steel; class: 1100 MPa/315 鳦/425 鳦) |
| DIN 65546-2005 |
航空航天系列.耐腐蚀钢制自锁紧、带深沉孔、凸缘和MJ螺纹的十二角螺母.等级:1100 MPa/315 鳦/425 鳦 |
|
| DIN 65547-1987 |
航空和航天.公制系列.钛合金钢制.带通用头配合铆钉 |
(Aerospace; rivets, close tolerance, with protruding head, metric series, titanium alloy) |
| DIN 65548-1987 |
航空和航天.钛合金钢制.公制系列.带埋头100°配合铆钉 |
(Aerospace; rivets, close tolerance with 100 flush head, metric series, titanium alloy) |
| DIN 65549-1987 |
航空和航天.钛合金钢制.公制系列.带埋头130°配合铆钉 |
(Aerospace; rivets, close tolerance with 130 flush head, metric series, titanium alloy) |
| DIN 65550-1987 |
航空和航天.公制系列.钛制.带箍闭合环 |
(Aerospace; flanged collars, metric series, titanium) |
| DIN 65551-1988 |
航空和航天.公制系列不锈钢制盲铆钉.带渐缩埋头100℃铆芯 |
(Aerospace; blind rivets with 100 reduced countersunk head, metric series, corrosion-resisting steel, with mandrel) |
| DIN 65552-1993 |
航空和航天.米制系列带铆芯100°沉头不锈钢盲铆钉 |
(Aerospace; blind rivets with 100 countersunk head, corrosion-resisting steel, with mandrel, metric series) |
| DIN 65553-2001 |
航空和航天.带MJ螺纹铆接螺母用无孔金属垫片 |
(Aerospace - Shims, without hole, for anchor nuts with MJ thread; Not to be used for new designs) |
| DIN 65554-1987 |
航空和航天.具有筋翼形十字槽和MJ螺纹.短螺纹.耐腐蚀钢制平头螺栓.额定抗拉强度1100MPa.温度可达425℃ |
(Aerospace; pan head bolts with ribbed TORQ-SET (ACR) recess and short-length MJ thread, corrosion-resisting steel, nominal tensile strength 1100 MPa, for temperatures up to 425 C) |
| DIN 65555-1987 |
航空和航天.带MJ螺纹.短螺纹.耐腐蚀钢制六角螺栓.额定抗拉强度1100MPa.温度可达425℃ |
(Aerospace; hexagon bolts with short-length MJ thread, corrosion-resisting steel; nominal tensile strength 1100 MPa, for temperatures up to 425 C) |
| DIN 65557-1989 |
航空和航天.带肋翼形螺纹接近头部.钛合金制.十字槽及MJ螺纹的平头螺钉.额定拉伸强度1100MPa温度至315℃ |
(Aerospace; pan head screws with ribbed TORQ-SET (ACR) recess and MJ thread, fully threaded, titanium alloy; nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65558-1989 |
航空和航天.带肋翼形全螺纹.钛合金制.十字槽及MJ螺纹的沉头螺钉.额定拉伸强度1100MPa.温度至315℃ |
(Aerospace; countersunk head screws, with ribbed TORQ-SET (ACR) recess and MJ thread, fully threaded, titanium alloy; nominal tensile strength 1100 MPa, for temperatures up to 315 C) |
| DIN 65559-1991 |
航空和航天.纤维增强塑料.多向层压板的检验.缺口抗拉强度的测定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of open-hole tensile strength) |
| DIN 65560-1991 |
航空和航天.纤维增强塑料.多向层压板的检验.缺口抗压强度的测定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of filled-hole compressive strength) |
| DIN 65561-1991 |
航空和航天.纤维增强塑料.多向层压板的检验.冲击负荷后抗压强度的测定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of compressive strength after impact test) |
| DIN 65562-1991 |
航空和航天.纤维增强塑料.多向层压塑料的检验.孔壁强度的测定 |
(Aerospace; fibre reinforced plastics; testing of multidirectional laminates; determination of bearing strength) |
| DIN 65564-1992 |
航空和航天.增强纤维.用HPLC法作碳素长丝纱、织物和短切原丝的浆成份的定性测定 |
(Aerospace; reinforcement fibres; qualitative determination of size constituents of carbon filament yarns, woven fabrics and chopped strands by HPLC) |
| DIN 65565-1992 |
航空和航天.增强纤维.用红外分光法作碳素长丝纱、织物和短切原丝的浆型的定性控制 |
(Aerospace; reinforcement fibres; qualitative testing of size type of carbon filament yarns, woven fabrics and chopped strands by infrared spectroscopy) |
| DIN 65566-1992 |
航空和航天.增强纤维.碳素长丝纱、织物和短切原丝的浆成份的测定 |
(Aerospace; reinforcement fibres; determination of size content of carbon filament yarns, woven fabrics and chopped strands) |
| DIN 65567-1992 |
航空和航天.增强纤维.芳族聚酰胺长丝纱,织物和短切原丝整理剂含量测定 |
(Aerospace; reinforcement fibres; determination of finish content of aramid filament yarns, woven fabrics and chopped strands) |
| DIN 65568-1992 |
航空和航天.增强纤维.碳素长丝纱、织物和短切原丝的热氧化稳定性的测定 |
(Aerospace; reinforcement fibres; determination of thermal oxidative resistance of carbon filament yarns, woven fabrics and short cuts) |
| DIN 65569-1-1992 |
航空和航天.增强纤维.复丝纱厚度的测定.悬浮法 |
(Aerospace; reinforcement fibres; determination of density of filament yarns; sink-float method) |
| DIN 65569-2-1992 |
航空和航天.增强纤维.复丝纱厚度的测定.浮力法 |
(Aerospace; reinforcement fibres; determination of density of filament yarns; hydrostatic weighing method) |
| DIN 65570-1990 |
航空和航天.热处理设备.一般要求 |
(Aerospace; heat treatment facilities; general requirements) |
| DIN 65571-1-1992 |
航空和航天.增强纤维.长丝纱截面面积和长丝直径的测定.计算方法 |
(Aerospace; reinforcement fibres; determination of filament diameter and cross-sectional area of filament yarns; calculation method) |
| DIN 65571-2-1992 |
航空和航天.增强纤维.长丝纱的长丝直径的测定.纵向投影法 |
(Aerospace; reinforcement fibres; determination of filament diameter of filament yarns; longitudinal projection method) |
| DIN 65571-3-1992 |
航空和航天.增强纤维.长丝纱的长丝直径、长丝截面形式和长丝截面面积的测定.横磨测量 |
(Aerospace; reinforcement fibres; determination of filament diameter, cross-sectional shape and area of filament yarns; measurement of transverse micro-section) |
| DIN 65571-4-1992 |
航空和航天.增强纤维.长丝纱的长丝直径的测定.激光干涉仪测量 |
(Aerospace; reinforcement fibres; determination of filament diameter of filament yarns; laser interferometry) |
| DIN 65572-1992 |
航空和航天.碳化纤维和无反应热塑塑料制单色直接配制预浸胶体.交货技术条件 |
(Aerospace; unidirectional sheet and tape prepreg from carbon fibres and non-reactive thermoplastics; technical specification) |
| DIN 65574-1993 |
航空和航天.部件铭牌.结构规范 |
(Aerospace; nameplates; directions for design) |
| DIN 65576-1991 |
航空和航天.带固定凸轮杆和单锁定解脱装置的不锈钢快卸销 |
(Aerospace; quick-release pins in corrosion-resisting steel, single locked, with self-retaining cam lever release mechanism) |
| DIN 65578-1991 |
航空和航天.带推或拉单锁定解脱装置不锈钢快卸销 |
(Aerospace; quick-release pins in corrosion-resisting steel, single locked, with pull or push release mechanism) |
| DIN 65581-1992 |
航空和航天.公制系列.钛合金制紧配合铆钉和纯钛制闭锁环.交货技术条件 |
(Aerospace; titanium-alloy close-tolerance rivets and pure-titanium collars, metric series; technical specification) |
| DIN 65582-1990 |
航空和航天.铝和镁合金铸件的热处理 |
(Aerospace; heat treatment of aluminium- and magnesium-alloy castings) |
| DIN 65583-1999 |
航空和航天.纤维增强塑料.动态负荷下纤维粘合材料的玻璃过渡的测定 |
(Aerospace - Fibre reinforced materials - Determination of glass transition of fibre composites under dynamic load) |
| DIN 65587-1992 |
航空和航天.输送带.交货技术条件 |
(Aerospace; webbing; technical specification) |
| DIN 65590-1992 |
航空和航天.编织亚麻制品.交货技术条件 |
(Aerospace; braided cord; technical specification) |
| DIN 65591-1998 |
航空和航天.非涂层宽幅织物.交货技术条件 |
(Aerospace - Broad woven fabric, uncoated - Technical specification) |
| DIN 65594-1993 |
航空和航天.英制系列平头实心铆钉的铆钉上头 |
(Aerospace; closing heads for solid rivets, pan head, inch based series) |
| DIN 65595-1993 |
航空和航天.米制系列平头实心铆钉的铆钉上头 |
(Aerospace; closing heads for solid rivets; pan head, metric series) |
| DIN 65597-1993 |
航空和航天.纤维增强塑料.放热反应时温差的测定 |
(Aerospace; fibre reinforced plastics; determination of temperature difference on exothermic reaction) |
| DIN 65598-1993 |
航空和航天.纤维增强塑料.层压制品裂纹频度测定 |
(Aerospace; fibre reinforced plastics; determination of cracking frequency on laminates) |
| DIN 65603-1982 |
航空和航天.钻模上9.9mm以下的钻孔色标 |
(Aerospace; colour identification of holes up to 9,9 mm on drilling jigs) |
| DIN 65604-1988 |
航空和航天.特种检验装置.颜色标记 |
(Aerospace; special gauging facilities; colour identification) |
| DIN 65629-1993 |
航空和航天.碳纤维和非活性热塑塑料制预浸渍布片和布带.交货技术条件 |
(Aerospace; fabric sheet and tape prepreg from carbon fibres and non-reactive thermoplastics; technical specification) |
| DIN 65668-1998 |
航空和航天.为了基本粒子计数而使油料稀释 |
(Aerospace series - Dilution of oils for the purpose of particles counting) |
| DIN 65669-1-1996 |
航空和航天.测定用过的液体过滤器件污染情况的方法.第1部分:通过材料试样提取作重力测定固体污染情况 |
(Aerospace series - Methods for determining the contamination of used fluid filter elements - Part 1: Gravimetric determination of particulate contamination by taking material samples) |
| DIN 65673-1999 |
航空和航天.纤维增强塑料.纱疵,织疵和预浸渍体疵点.定义 |
(Aerospace - Fibre reinforced plastics - Description of yarn, fabric and prepreg defects) |
| DIN 65736-1-1984 |
航空和航天.单槽.螺钉材料1.1174.7和1.4544.9.沉头螺钉静负荷时的螺钉计算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt materials 1.1174.7 and 1.4544.9) |
| DIN 65736-3-1984 |
航空和航天.单槽.螺钉材料1.7220.5.沉头螺钉静负荷时的螺钉计算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt material 1.7220.5) |
| DIN 65736-5-1984 |
航空和航天.单槽.螺钉材料1.4944.4和1.7734.5.沉头螺钉静负荷时的螺钉计算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt materials 1.4944.4 and 1.7734.5) |
| DIN 65736-7-1984 |
航空和航天.单槽.螺钉材料1.6604.6.沉头螺钉静负荷时的螺钉计算值 |
(Aerospace; bolt calculation values, static load, for countersunk head bolts, single shear, bolt material 1.6604.6) |
| DIN 6580-1985 |
切削工艺的概念.切削过程的运动和几何形态 |
(Terminology of chip removing; movements and geometry of the chip removing process) |
| DIN 6581-1985 |
切削工艺的概念.刀具切削部分的参考系统和角度 |
(Terminology of chip removing; reference systems and angles on the cutting part of the tool) |
| DIN 6582-1988 |
切削工艺的概念.刀具 |
(Terminology of cutting; additional terms for the tool, wedge and the cutting edge) |
| DIN 6583-1981 |
切削工艺的概念.刀具寿命概念 |
(Terms of cutting procedures; tool life criteria) |
| DIN 6584-1982 |
切削工艺的概念.切削力.能量.切削功.功率 |
(Terms of the cutting technique; forces, energy, work, power) |
| DIN 659-1982 |
管制套筒板手 |
(Tubular single end tee socket wrenches) |
| DIN 6590-1986 |
平面刃硬质合金无固定孔转位式刀片 |
(Indexable hardmetall (carbide) inserts with wiper edges, without fixation hole) |
| DIN 6594-1998 |
转位式刀片用符合DIN69893-1A型要求的带圆锥空心杆和冷却润滑剂导槽的钻头 |
(Drills with hollow taper shanks and coolant fluid supply according to DIN 69893-1 type A for indexable inserts - Main dimensions) |
| DIN 6595-1993 |
带转位刀片的钻头.直柄 |
(Drills with indexable inserts; parallel shanks) |
| DIN 6596-1998 |
转位式刀片用符合DIN69893-1A型要求的带圆锥空心杆和冷却润滑剂导槽的钻头.标识 |
(Drills with hollow taper shanks and coolant fluid supply according to DIN 69893-1 type A for indexable inserts - Designation) |
| DIN 6597-2004 |
可转位刀片用符合DIN 69893-1和DIN 69893-2的外部和内部旋转带中空锥柄的工具夹.名称与符号 |
|
| DIN 6598-2004 |
可转位刀片用符合DIN 69893-1的外部和内部旋转带中空锥柄的工具夹.与尺寸相关的概述 |
|
| DIN 6599-1998 |
切削机械用硬质切销材料的可用性 |
(Applicability of hard cutting materials for machining by chip removal - Information additional to ISO 513 designation (ISO/TR 11255:1994)) |
| DIN 66-1990 |
符合DINISO7721要求.通用沉头螺钉头的倾斜度 |
(Countersinks for countersunk head screws with ISO 7721 common head style) |
| DIN 660-1993 |
半圆头铆钉.公称直径1至8mm |
(Round head rivets; nominal diameters 1 to 8 mm) |
| DIN 6600-1989 |
存储污染水的易燃和不易燃液体用的钢制容器(罐).质量监督 |
(Steel tanks for the storage of flammable and non-flammable water polluting liquids; concepts and inspection) |
| DIN 66000-1985 |
信息处理.开关代数的数学符号 |
(Information processing; switching algebra, mathematical signs and symbols) |
| DIN 66001 Bb.1-1983 |
信息处理.示意图符号及其用途.符号样板上示意图的排列 |
(Information processing; graphical symbols and their application; layout of graphical symbols on a template) |
| DIN 66001-1983 |
信息处理.示意图符号及其用途 |
(Information processing; graphical symbols and their application) |
| DIN 66002-1975 |
信息处理；数字０和大写字母Ｏ的手写体 |
(Information processing; handwriting of the digit 0 and of the upper case letter O) |
| DIN 66003-1999 |
信息处理.7位代码 |
(Information technology - 7-bit code) |
| DIN 66004-1-1983 |
信息处理.数据载体编码.在孔带25上的7位码的表达方法 |
(Information processing; coding on data media; representation of 7-bit code character sets on punched tape 25) |
| DIN 66004-2-1982 |
信息处理.数据载体编码.在穿孔卡上的7位码和8位码的表达方法 |
(Information processing; coding on data media; representation of 7-bit coded and 8-bit coded character sets on punched cards) |
| DIN 66004-3-1983 |
信息处理.数据载体编码.在磁带12上的7位码和8位码的表达方法 |
(Information processing; coding on data media; representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12) |
| DIN 66004-4-1982 |
信息处理.数据载体编码.在盒式磁带3.8上的7位码和8位码的表达方法 |
(Information processing; coding on data media; representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8) |
| DIN 66004-5-1999 |
信息处理.数据载体编码.第5部分:在软盘上的7位码和8位码的表达方法 |
(Information processing - Coding on data media - Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridge) |
| DIN 66005-1988 |
信息处理.在有9个磁道记录的磁带12上纯数字数据节省空间的显示 |
(Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12) |
| DIN 66008-1-1989 |
机械光学字符识别用字体A.字符和公称尺寸 |
(Font A for optical character recognition; characters and nominal dimensions) |
| DIN 66008-6-1985 |
机械光学字符识别用字体A.字符与公称尺寸.字符集的扩展 |
(Font A for optical character recognition; characters and nominal dimensions; extension of the character set) |
| DIN 66008-7-1985 |
机械光学字符识别用字体A.字符的9×9点阵的表示 |
(Font A for optical character recognition; representation of characters by dots in a 99 matrix) |
| DIN 66009-1977 |
机械光学字符识别用字体B.字符.公称尺寸和字符载体上的格式 |
(Font B for optical character recognition; characters, nominal dimensions, and format) |
| DIN 6601-1991 |
钢制容器/储罐的材料对液体的耐蚀性(正性液体表) |
(Resistance of materials of steel tanks against liquids (positiv-list of liquids)) |
| DIN 66010-1988 |
信息处理存储和交换数字数据用软磁数据载体.概念 |
(Information processing; flexible magnetic data media, for the storage and the interchange of digital data; concepts) |
| DIN 66013-1977 |
数字数据存储用7磁道的不归零制记录磁带.位密度8位/毫米 |
(On 7 tracks nonreturn to zero (one) recorded magnetic tape for digital data storage, density 8 rpmm (200 rpi)) |
| DIN 66014-1-1977 |
数字数据存储用9磁道的不归零制记录磁带.位密度8位/毫米 |
(On 9 track nonreturn to zero (one) recorded magnetic tape for digital data storage, density 8 rpmm (200rpi)) |
| DIN 66014-2-1977 |
数字数据存储用9磁道的不归零制记录磁带.位密度32位/毫米 |
(On 9 tracks nonretorn to zero (one) recorded magnetic tape for digital data storage, density 32 rpmm (800 rpi)) |
5分钟获取标准报价 咨询电话：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com