标准号 |
中文名称 |
英文名称 |
| DIN EN 713-1994 |
塑料管道系统.异型件和聚烯烃压力管间的机械连接.在内压和弯曲下密封性检验法 |
(Plastics piping systems; mechanical joints between fittings and polyolefin pressure pipes; test method for leaktightness under internal pressure of assemblies subjected to bending; German version EN 713:1993) |
| DIN EN 714-1994 |
热塑管道系统.在压力管和管件之间带橡胶密封环的非抗拉连接件.无轴向应力的静力内压下密封性的检验方法 |
(Thermoplastics piping systems - Non-end-load-bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - Test method for leaktightness under internal hydrostatic pressure whithout end thrust; German version EN 714:1994) |
| DIN EN 715-1994 |
热塑塑料管道系统.压力管和小口径异型件间抗拉连接.水内压和轴向应力下密封检验 |
(Thermoplastics piping systems; end-load bearing joints between small diameter pressure pipes and fittings; test method for leaktightness under internal water pressure, including end thrust; German version EN 715:1994) |
| DIN EN 716-1-1995 |
家具.居室用儿童床和旅行儿童床.第1部分:安全技术要求 |
(Furniture - Children`s cots and folding cots for domestic use - Part 1: Safety requirements; German version EN 716-1:1995) |
| DIN EN 716-2-1995 |
家具.居室用儿童床和旅行儿童床.第2部分:检验方法 |
(Furniture - Children`s cots and folding cots for domestic use - Part 2: Test methods; German version EN 716-2:1995) |
| DIN EN 717-1-2005 |
木基板材.甲醛释出的测定.第1部分:用燃烧室法测定甲醛的排放量 |
|
| DIN EN 717-2 Berichtigung 1-2003 |
DINEN717-2-1995的技术勘误 |
(Corrigenda to DIN EN 717-2:1995-01 (EN 717-2:1994/AC:2002)) |
| DIN EN 717-2-1995 |
木材.甲醛释出的测定.第2部分:按气体分析法释出甲醛 |
(Wood-based panels - Determination of formaldehyde release - Part 2: Formaldehyde release by the gas analysis method; German version EN 717-2:1994) |
| DIN EN 717-3-1996 |
木基材.甲醛释出的测定.第3部分:按瓶法释出甲醛 |
Wood-based panels - Determination of formaldehyde release - Part 3: Formaldehyde release by the flask method; German version EN 717-3:1996 |
| DIN EN 718-1996 |
弹性地板铺面.聚氯乙烯地板铺面加衬或加固单位面积质量的测定 |
(Resilient floor coverings - Determination of mass per unit area of a reinforcement or a backing of polyvinylchlorid; German version EN 718:1995) |
| DIN EN 719-1994 |
焊接堆层.任务和责任 |
(Welding coordination - Tasks and responsibilities; German version EN 719:1994) |
| DIN EN 720-1-1999 |
移动式煤气瓶.煤气和煤气混合物.第1部分:纯煤气的特性 |
(Transportable gas cylinders - Gases and gas mixtures - Part 1: Properties of pure gases; German version EN 720-1:1999) |
| DIN EN 720-2-1996 |
移动式煤气瓶.煤气和混合气体易燃性和氧化能力的测定 |
(Transportable gas cylinders - Gases and gas mixtures - Part 2: Determination of flammability and oxidizing ability of gases and gas mixtures; German version EN 720-2:1996) |
| DIN EN 721-1998 |
可居住的休闲旅游车.安全通风的要求 |
(Leisure accommodation vehicles - Safety ventilation requirements; German version EN 721:1998) |
| DIN EN 721-2004 |
旅居车.安全通风要求 |
|
| DIN EN 722-1-1996 |
可居住的休闲车辆.用燃料驱动的暖气设备.第1部分:居住拖车和自走式居住车 |
(Leisure accommodation vehicles - Liquid fuel heating systems - Part 1: Caravans and mobile homes; German version EN 722-1:1996) |
| DIN EN 722-1-2004 |
旅居车.液体燃料供暖系统.第1部分:旅居挂车和渡假活动房屋 |
|
| DIN EN 723-1996 |
铜和铜合金.通过燃烧测定铜管或管件内表面碳素的方法 |
(Copper and copper alloys - Combustion method for determination of carbon on the inner surface of copper tubes or fittings; German version EN 723:1996) |
| DIN EN 724-1994 |
非活性医疗器械的EN29001,EN46001,EN29002和EN46002的使用指南 |
(Guidance on the application of EN 29001 and EN 46001 and of EN 29002 and EN 46002 for non-active medical devices; German version EN 724:1994) |
| DIN EN 725-1-1997 |
高效陶瓷.陶瓷粉末的检验方法.第1部分:铝氧粉末中杂质测定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 1: Determination of impurities in alumina; German version EN 725-1:1997) |
| DIN EN 725-10-1997 |
高效陶瓷.陶瓷粉末的检验方法.第10部分:压缩性能测定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 10: Determination of compaction properties; German version EN 725-10:1997) |
| DIN EN 725-12-2001 |
高级工程陶瓷.陶瓷粉末的检验方法.第1部分:锆的化学分析 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 12: Chemical analysis of zirconia; German version EN 725-12:2001) |
| DIN EN 725-3-1994 |
高效陶瓷.陶瓷粉末的检验方法.用气体载体热萃取测定非氧化粉末中的氧含量 |
(Advanced technical ceramics; methods of test for ceramic powders; part 3: determination of the oxygen content of non-oxides by thermal extraction with a carrier gas; German version EN 725-3:1994) |
| DIN EN 725-5-1996 |
高效陶瓷.陶瓷粉末的检验方法.第5部分;粒度分布测定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 5: Determination of the particle size distribution; German version EN 725-5:1996) |
| DIN EN 725-6-1996 |
高效陶瓷.陶瓷粉末的检验方法.第6部分:特殊表面的测定 |
Advanced technical ceramics - Methods of test for ceramic powders - Part 6: Determination of the surface area; German version EN 725-6:1996 |
| DIN EN 725-7-1996 |
高效陶瓷.陶瓷粉末的检验方法.第7部分:绝对密度测定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 7: Determination of the absolute density; German version EN 725-7:1995) |
| DIN EN 725-8-1997 |
高效陶瓷.陶瓷粉末的检验方法.第8部分:振实密度的测定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 8: Determination of tapped bulk density; German version EN 725-8:1997) |
| DIN EN 725-9-1997 |
高效陶瓷.陶瓷粉末的检验方法.第8部分:堆积密度的测定 |
(Advanced technical ceramics - Methods of test for ceramic powders - Part 9: Determination of untamped bulk density; German version EN 725-9:1997) |
| DIN EN 726-1-1995 |
识别卡系统.用于电讯的终端和芯片卡的要求.第1部分:系统概述 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 1: systems overview; German version EN 726-1:1994) |
| DIN EN 726-2-1996 |
识别卡系统.用于电讯的终端和芯片卡.第2部分:安全性基础构架 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 2: Security framework; German version EN 726-2:1995) |
| DIN EN 726-3-1995 |
识别卡系统.用于电讯的终端和芯片卡的要求.第1部分:对卡的单独使用要求 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 3: Application independent card requirements; German version EN 726-3:1995) |
| DIN EN 726-4-1995 |
识别卡系统.用于电讯的终端和芯片卡的要求.第4部分:终端上独立使用的卡关联要求 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 4: Application independent card related terminal requirements; German version EN 726-4-1994) |
| DIN EN 726-5-2000 |
识别卡系统.电信集成线路卡和终端.第5部分:付款方法 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 5: Payment methods; German version EN 726-5:1999) |
| DIN EN 726-6-1996 |
识别卡系统.用于电讯的芯片卡和终端.第6部分:功率特性 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 6: Telecommunication features; German version EN 726-6:1995) |
| DIN EN 726-7-2000 |
识别卡系统.电信集成电路卡和终端.第7部分:安全模式 |
(Identification card systems - Telecommunications integrated circuit(s) cards and terminals - Part 7: Security module; German version EN 726-7:1999) |
| DIN EN 727-1995 |
塑料管道和防护管系统.热塑管和异型件.维卡软化温度(VST)的测定 |
(Plastics piping and ducting systems - Thermoplastics pipes and fittings - Determination of Vicat softening temperature (VST); German version EN 727:1994) |
| DIN EN 728-1997 |
塑料管道系统和保护管系统.聚烯烃制管和管件.氧化感应时间测定 |
(Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time; German version EN 728:1997) |
| DIN EN 729-1-1994 |
焊接技术质量要求.金属材料熔焊.第1部分:选择和使用规则 |
(Quality requirements for welding - Fusion welding of metallic materials - Part 1: Guidelines for selection and use; German version EN 729-1:1994) |
| DIN EN 729-2-1994 |
焊接技术质量要求.金属材料熔焊.第2部分:全面质量要求 |
(Quality requirements for welding - Fusion welding of metallic materials - Part 2: Comprehensive quality requirements; German version EN 729-2:1994) |
| DIN EN 729-3-1994 |
焊接技术质量要求.金属材料熔焊.第3部分:标准质量要求 |
(Quality requirements for welding - Fusion welding of metallic materials - Part 3: Standard quality requirements; German version EN 729-3:1994) |
| DIN EN 729-4-1994 |
焊接技术质量要求.金属材料溶焊.第4部分:基本质量要求 |
(Quality requirements for welding - Fusion welding of metallic materials - Part 4: Elementary quality requirements; German version EN 729-4:1994) |
| DIN EN 73-1990 |
木材防腐剂.生物检验前被处理木材的加速老化.蒸发老化过程 |
(Wood preservatives; accelerated ageing tests of treated wood prior to biological testing; evaporative ageing procedure; german version EN 73:1988) |
| DIN EN 730-1-2003 |
气焊设备.安全装置.第1部分:含有回火制止器的安全装置 |
(Gas welding equipment - Safety devices - Part 1: Incorporating a flame (flashback) arrestor; German version EN 730-1:2002) |
| DIN EN 730-2-2003 |
气焊设备.安全装置.第2部分:不含有回火制止器的安全装置 |
(Gas welding equipment - Safety devices - Part 2: Not incorporating a flame (flashback) arrestor; German version EN 730-2:2002) |
| DIN EN 731-1995 |
气焊设备.吸气式手提吹管.规范和试验 |
(Gas welding equipment - Air-aspirated hand blowpipes - Specifications and tests; German version EN 731:1995) |
| DIN EN 732-1999 |
液化石油气器具规范.吸收式冰箱 |
(Specification for dedicated liquefied petroleum gas appliances - Absorption refrigerators; German version EN 732:1998) |
| DIN EN 733-1995 |
带轴承座和PN10轴向端口的离心泵.额定功率.主要尺寸.标识系统 |
(End-suction centrifugal pumps, rating 10 bar with bearing bracket - Nominal duty point, main dimensions, designation system; German version EN 733:1995) |
| DIN EN 734-1995 |
带侧通道泵PN40.额定功率.主要尺寸.标识系统 |
(Side channel pumps PN 40 - Nominal duty point, main dimensions, designation system; German version EN 734:1995) |
| DIN EN 735-1995 |
旋转动态泵的总体尺寸.公差 |
(Overall dimensions of rotodynamic pumps - Tolerances; German version EN 735:1995) |
| DIN EN 736-1-1995 |
管件.术语.第1部分:基本结构定义 |
(Valves - Terminology - Part 1: Definition of types of valves; German version EN 736-1:1995) |
| DIN EN 736-2-1997 |
阀门.术语.第2部分:阀门部件的定义 |
(Valves - Terminology - Part 2: Definition of components of valves; German version EN 736-2:1997) |
| DIN EN 736-3-2002 |
阀门.术语.第3部分:术语定义(包括修改件A1) |
(Valves - Terminology - Part 3: Definition of terms (includes Amendment A1:2001); German version EN 736-3:1999 + A1:2001) |
| DIN EN 737-1-1998 |
医疗气体用管道系统.第1部分:医疗压缩气体和真空用取样点 |
(Medical gas pipeline systems - Part 1: Terminal units for compressed medical gases and vacuum; German version EN 737-1:1998) |
| DIN EN 737-2-2000 |
医疗气体管道系统.第2部分:麻醉气清除系统.基本要求(包括修改件A1) |
(Medical gas pipeline systems - Part 2: Anaesthetic gas scavenging disposal systems; basic requirements (includes Amendment A1:1999); German version EN 737-2:1998 + A1:1999) |
| DIN EN 737-3-2000 |
医疗气体管道系统.第3部分:医疗压缩气体和真空管道 |
(Medical gas pipeline systems - Part 3: Pipelines for compressed medical gases and vacuum (includes Amendment A1:1999); German version EN 737-3:1998 + A1:1999) |
| DIN EN 737-4-1998 |
医疗气体用管道系统.第4部分:麻醉气体传导系统用取样点 |
(Medical gas pipeline systems - Part 4: Terminal units for anaesthetic gas scavenging systems; German version EN 737-4:1998) |
| DIN EN 738-1-2002 |
医疗气体用压力调节器.第1部分:压力调节器和带流量测量装置的压力调节器 |
(Pressure regulators for use with medical gases - Part 1: Pressure regulators and pressure regulators with flow metering devices (includes Amendment A1:2002); German version EN 738-1:1997 + A1:2002) |
| DIN EN 738-2-1998 |
医疗气体用压力调节器.第2部分:歧管和管线压力调节器 |
(Pressure regulators for use with medical gases - Part 2: Manifold and line pressure regulators; German version EN 738-2:1998) |
| DIN EN 738-3-2002 |
医疗气体用压力调节器.第3部分:与气瓶阀整合的压力调节器 |
(Pressure regulators for use with medical gases - Part 3: Pressure regulators integrated with cylinder valves (includes Amendment A1:2001); German version EN 738-3:1998 + A1:2001) |
| DIN EN 738-4-2002 |
医疗气体用压力调节器.第4部分:医疗设备中使用的低压调节器(包括修改件A1) |
(Pressure regulators for use with medical gases - Part 4: Low-pressure regulators intended for incorporation into medical equipment (includes Amendment A1:2002); German version EN 738-4:1998 + A1:2002) |
| DIN EN 739-2002 |
医疗气体用低压软管组件(包括修改件A1) |
(Low-pressure hose assemblies for use with medical gases (includes Amendment A1:2002); German version EN 739:1998 + A1:2002) |
| DIN EN 74-1-2005 |
脚手架和支承架用联结件、中心螺栓和踏板.第1部分:钢管用联结件.要求和试验规程.德文版本 EN 74-1-2005德文版 |
|
| DIN EN 74-1988 |
联结件.钢管脚手架和支承架用中心螺栓和踏板.要求.检验 |
(Couplers, loose spigots and base-plates for use in workung scaffolds and falsework made of steel tubes; requirements and test procedures; german version EN 74:1988) |
| DIN EN 740-1999 |
麻醉工作场所和它们的模式.特殊规定 |
(Anaesthetic workstations and their modules - Particular requirements (including corrigendum AC:1998); German version EN 740:1998 + AC:1998) |
| DIN EN 740/A1-2004 |
麻醉工作台及其组件.特殊要求 |
|
| DIN EN 741-2000 |
连续装卸设备和系统.松散材料的气压装卸系统及其部件的安全要求 |
(Continuous handling equipment and systems - Safety requirements for systems and their components for pneumatic handling of bulk materials; German version EN 741:2000) |
| DIN EN 742-1994 |
识别卡系统.欧州仪器上用1型识别卡接触位置和安排 |
(Identification card systems; intersector ID-1 card location of contacts for cards and devices used in Europe; German version EN 742:1993) |
| DIN EN 743-1994 |
塑料管道和防护管系统.热塑塑料管道.纵向收缩测定 |
(Plastics piping and ducting systems; thermoplastics pipes; determination of the longitudinal reversion; german version EN 743:1994) |
| DIN EN 744-1995 |
塑料管道和导管系统.热塑管.耐连续吹风的试验方法 |
(Plastics piping and ducting systems - Thermoplastics pipes - Test method for resistance to external blows by the round-the-clock-method; German version EN 744:1995) |
| DIN EN 745-1999 |
农业机械.旋转式割草机构和甩刀式割草机.安全性 |
(Agricultural machinery - Rotary mowers and flail mowers - Safety; German version EN 745:1999) |
| DIN EN 746-1-1997 |
工业热加工工艺设备.第1部分:工业热加工工艺设备的一般安全要求 |
(Industrial thermoprocessing equipment - Part 1: Common safety requirements for industrial thermoprocessing equipment; German version EN 746-1:1997) |
| DIN EN 746-2-1997 |
工业热加工工艺设备.第2部分:燃烧和燃料储运系统的安全要求 |
(Industrial thermoprocessing equipment - Part 2: Safety requirements for combustion and fuel handling systems; German version EN 746-2:1997) |
| DIN EN 746-3-1997 |
工业热加工工艺设备.第3部分:保护气体和反应气体的生产和使用的安全要求 |
(Industrial thermoprocessing equipment - Part 3: Safety requirements for the generation and use of atmospheres gases; German version EN 746-3:1997) |
| DIN EN 746-4-2000 |
工业热加工设备.第4部分:热浸电镀热加工设备的特殊安全要求 |
(Industrial thermoprocessing equipment - Part 4: Particular safety requirements for hot dip galvanising thermoprocessing equipment; German version EN 746-4:1999) |
| DIN EN 746-5-2001 |
工业热处理设备.第5部分:盐浴热处理设备的特殊安全要求 |
(Industrial thermoprocessing equipment - Part 5: Particular safety requirements for salt bath thermoprocessing equipment; German version EN 746-5:2000) |
| DIN EN 746-8-2001 |
工业热处理设备.第8部分:淬火设备的特殊安全要求 |
(Industrial thermoprocessing equipment - Part 8: Particular safety requirements for quenching equipment; German version EN 746-8:2000) |
| DIN EN 747-1-1993 |
家具.卧室用双层床.第1部分:安全性要求 |
(Furniture; bunk beds for domestic use; part 1: safety requirements; German version EN 747-1:1993) |
| DIN EN 747-2-1993 |
家具.卧室用双层床.第2部分:检验方法 |
(Furniture; bunk beds for domestic use; part 2: test methods; German version EN 747-2:1993) |
| DIN EN 748-1999 |
运动场地器材.足球门.功能和安全技术要求,检验方法(包括修改件1:1998) |
(Playing field equipment - Football goals - Functional and safety requirements, test methods (including amendment 1:1998); German version EN 748:1995 + A1:1998) |
| DIN EN 748-2004 |
运动场地器材.足球门.功能和安全技术要求及试验方法 |
|
| DIN EN 748-2004 |
运动场地器材.足球门.功能和安全技术要求及试验方法 |
|
| DIN EN 749-1999 |
运动场地器材.手球门.功能和安全技术要求,检验方法(包括修改件1:1998) |
(Playing field equipment - Handball goals - Functional and safety requirements, test methods (including amendment 1:1998); German version EN 749:1995 + A1:1998) |
| DIN EN 749-2004 |
运动场地器材.手球门.功能和安全技术要求及试验方法 |
|
| DIN EN 750-1999 |
运动场地器材.曲棍球门.功能和安全技术要求,检验方法(包括修改件1:1998) |
(Playing field equipment - Hockey goals - Functional and safety requirements, test methods (including amendment 1:1998); German version EN 750:1995 + A1:1998) |
| DIN EN 750-2004 |
运动场地器材.曲棍球门.功能和安全技术要求及试验方法 |
|
| DIN EN 751-1-1997 |
和第1,第2及第3族气体以及热水接触的金属螺纹连接用密封材料.第1部分:厌氧密封材料 |
Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 1: Anaerobic jointing compounds; German version EN 751-1:1996 |
| DIN EN 751-2-1997 |
和第1,第2及第3族气体以及热水接触的金属螺纹连接用密封材料.第2部分:非时效硬化的密封材料 |
(Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 2: Non-hardening jointing compounds; German version EN 751-2:1996) |
| DIN EN 751-3-1997 |
和第1,第2及第3族气体以及热水接触的金属螺纹连接用密封材料.第3部分:非烧结的PTFE带材 |
(Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water - Part 3: Unsintered PTFE tapes; German version EN 751-3:1996) |
| DIN EN 752 Bb.1-1999 |
建筑物外的污水排放系统.索引 |
(Drain and sewer systems outside buildings - Index) |
| DIN EN 752-1-1996 |
建筑物外部排水系统.第1部分:概述和定义 |
(Drain and sewer systems outside buildings - Part 1: Generalities and definitions; German version EN 752-1:1995) |
| DIN EN 752-2-1996 |
建筑物外部排水系统.第2部分:要求 |
(Drain and sewer systems outside buildings - Part 2: Performance requirements; German version EN 752-2:1996) |
| DIN EN 752-3-1996 |
建筑物外部排水系统.第3部分:规划 |
(Drain and sewer systems outside buildings - Part 3: Planning; German version EN 752-3:1996) |
| DIN EN 752-4-1997 |
建筑物外部排水系统.第4部分:液压计算和对环境保护的考虑 |
(Drain and sewer systems outside buildings - Part 4: Hydraulic design and environmental considerations; German version EN 752-4:1997) |
| DIN EN 752-5-1997 |
建筑物外部排水系统.第5部分:整理复原 |
(Drain and sewer systems outside buildings - Part 5: Rehabilitation; German version EN 752-5:1997) |
| DIN EN 752-6-1998 |
建筑物外部排水系统.第6部分:泵设备 |
(Drain and sewer systems outside buildings - Part 6: Pumping installations; German version EN 752-6:1998) |
| DIN EN 752-7-1998 |
建筑物外部排水系统.第7部分:操作和维护 |
(Drain and sewer systems outside buildings - Part 7: Maintenance and operations; German version EN 752-7:1998) |
| DIN EN 753-1-1998 |
识别卡系统.部门间重叠的薄型易弯曲卡.第1部分:一般技术规范 |
(Identification card systems - Intersector thin flexible cards - Part 1: General technical specifications; German version EN 753-1:1997) |
| DIN EN 753-2-1998 |
识别卡系统.部门间重叠的薄型易弯曲卡.第2部分:磁录制技术 |
Identification card systems - Intersector thin flexible cards - Part 2: Magnetic recording technique; German version EN 753-2:1997 |
| DIN EN 753-3-2000 |
识别卡系统.部门间薄型易弯曲卡.第3部分:德文版本EN753-3:1999 |
Identification card systems - Intersector thin flexible cards - Part 3: Test methods; German version EN 753-3:1999 |
| DIN EN 754-1-1997 |
铝和铝合金.冷拉棒和管.第1部分:交货技术条件 |
(Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 1: Technical conditions for inspection and delivery; German version EN 754-1:1997) |
| DIN EN 754-2-1997 |
铝和铝合金.冷拉棒和管.第2部分:机械性能 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 2: Mechanical properties; German version EN 754-2:1997 |
| DIN EN 754-3-1996 |
铝和铝合金.冷拉棒和管.第3部分:圆棒材.极限尺寸和形状公差 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 3: Round bars, tolerances on dimensions and form; German version EN 754-3:1995 |
| DIN EN 754-4-1996 |
铝和铝合金.冷拉棒和管.第4部分:方形棒材.极限尺寸和形状公差 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 4: Square bars, tolerances on dimensions and form; German version EN 754-4:1995 |
| DIN EN 754-5-1996 |
铝和铝合金.冷拉棒和管.第4部分:矩形棒材.极限尺寸和形状公差 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 5: Rectangular bars, tolerances on dimensions and form; German version EN 754-5:1995 |
| DIN EN 754-6-1996 |
铝和铝合金.冷拉棒和管.第4部分:六角形棒材.极限尺寸和形状公差 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 6: Hexagonal bars; tolerances on dimensions and form; German version EN 754-6:1995 |
| DIN EN 754-7-1998 |
铝和铝合金.冷拉棒和管.第7部分:无缝管.极限尺寸和形状公差 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 7: Seamless tubes, tolerances on dimensions and form; German version EN 754-7:1998 |
| DIN EN 754-8-1998 |
铝和铝合金.冷拉棒和管.第8部分:带连续压制小口的管.极限尺寸和形状 |
Aluminium and aluminium alloys - Cold drawn rod/bar and tube - Part 8: Porthole tubes, tolerances on dimensions and form; German version EN 754-8:1998 |
| DIN EN 755-1-1997 |
铝和铝合金.挤压棒材/管材和型材.第1部分:交货技术条件 |
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 1: Technical conditions for inspection and delivery; German version EN 755-1:1997 |
| DIN EN 755-2-1997 |
铝和铝合金.挤压竿材/棒材、管材和型材.第2部分:机械性能 |
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties; German version EN 755-2:1997 |
| DIN EN 755-3-1995 |
铝和铝合金.挤压竿材/棒材、管材和型材.第3部分:圆形棒材.尺寸和形状公差 |
Aluminium and aluminium alloys - Extruded rod/bar, tube and profile - Part 3: Round bars; tolerances on dimensions and form; German version EN 755-3:1995 |
| DIN EN 755-4-1995 |
铝和铝合金.挤压竿材/棒材、管材和型材.第4部分:方形棒材.尺寸和形状公差 |
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 4: Square bars, tolerances on dimensions and form; German version EN 755-4:1995 |
| DIN EN 755-5-1995 |
铝和铝合金.挤压竿材/棒材、管材和型材.第5部分:矩形棒材.尺寸和形状公差 |
(Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 5: Rectangular bars, tolerances on dimensions and form; German version EN 755-5:1995) |
| DIN EN 755-6-1995 |
铝和铝合金.挤压竿材/棒材、管材和型材.第6部分;六角形棒材.尺寸和形状公差 |
(Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 6: Hexagonal bars, tolerances on dimensions and form; German version EN 755-6:1995) |
| DIN EN 755-7-1998 |
铝和铝合金.挤压棒材/管材和型材.第7部分:无缝管.极限尺寸和形状公差 |
Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 7: Seamless tubes, tolerances on dimensions and form; German version EN 755-7:1998 |
| DIN EN 755-8-1998 |
铝和铝合金.挤压棒材/管材和型材.第8部分:带连续压制小口的管.极限尺寸和形状公差 |
(Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 8: Porthole tubes, tolerances on dimensions and form; German version EN 755-8:1998) |
| DIN EN 755-9-2001 |
铝和铝合金.挤压棒材/管材和型材.第9部分:截面图、尺寸和形状公差 |
(Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 9: Profiles, tolerances on dimensions and form; German version EN 755-9:2001) |
| DIN EN 756-1995 |
焊料.非合金钢和细粒钢埋弧焊用焊丝和焊丝-焊剂混合物.分类 |
(Welding consumables - Wire electrodes and wire-flux combinations for submerged arc welding of non alloy and fine grain steels - Classification; German version EN 756:1995) |
| DIN EN 756-2004 |
焊接消耗品.非合金钢和细粒钢埋弧焊用实芯焊丝、实芯焊丝和药芯焊丝混合助熔剂.分类 |
|
| DIN EN 757-1997 |
焊接添加剂.高强钢手动电弧焊用带涂药包皮的焊条.分类 |
(Welding consumables - Covered electrodes for manual metal arc welding of high strength steels - Classification; German version EN 757:1997) |
| DIN EN 758-1997 |
焊接材料.用和不用非合金钢以及细晶粒钢保护气体的金属电弧焊用管状焊条.分类 |
(Welding consumables - Tubular cored electrodes for metal arc welding with and without a gas shield of non alloy and fine grain steels - Classification; German version EN 758:1997) |
5分钟获取标准报价 咨询电话：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com