标准号 |
中文名称 |
英文名称 |
DIN 4340-1976 |
燃气轮机.概念.名称 |
(Gas Turbines; Definitions, Designations) |
DIN 4341-1-1979 |
燃气轮机.燃气轮机的验收规则.原理 |
(Gas turbines; acceptance tests) |
DIN 4341-2-1986 |
燃气轮机.燃气轮机的验收规则.计值举例 |
(Gas turbines; acceptance tests; examples for evalution) |
DIN 4342-1979 |
燃气轮机.标准参考条件.标准功率.运行数据说明 |
(Gas turbines; standard reference conditions, standard power and performance data) |
DIN 43451-1982 |
单级隔离开关.额定电压420KV.连接尺寸和固定尺寸.配置 |
(Vertical reach (pantograph) disconnector; rated voltage 420 kV; terminal and mounting dimensions, layout) |
DIN 43452-1988 |
闸刀垂直旋转式隔离开关.额定电压420V.连接尺寸和固定尺寸.配置 |
(Vertical break disconnector; rated voltage 420 kV; terminal and mounting dimensions, layout) |
DIN 43453-1985 |
单级接地开关.额定电压为420KV.连接尺寸和固定尺寸.配置 |
(Single-post earthing switch; rated voltage 420 kV; terminal and mounting dimensions, layout) |
DIN 43454-1-1987 |
断路器.额定电压123KV.连接和固定尺寸.配置 |
(Circuit-breaker; rated voltge 123 kV; terminal and mounting dimensions, layout) |
DIN 43454-2-1991 |
断路器.额定电压245KV的多极带公共底座的开关.连接尺寸和固定尺寸.配置 |
(Circuit-breaker; rated voltage 245 kV; circuit-breaker with common support frame for all poles; terminal and mounting dimensions, layout) |
DIN 43454-3-1987 |
断路器.额定电压为420KV.连接和固定尺寸.配置 |
(Circuit-breaker; rated voltage 420 kV; terminal and mounting dimensions, layout) |
DIN 43454-4-1999 |
断路器.额定电压245kV.每极用的分离支架 |
(Circuit-breaker - Rated voltage 245 kV - With a separate support frame for each pole) |
DIN 43455-1990 |
52KV以下高压开关设备操作用图形符号 |
(Graphical symbols for operation of high-voltage switchgear less than 52 kV) |
DIN 43456-1-1999 |
辅助电路用端子标识.第1部分:电压≥52kV用隔离开关和接地开关 |
(Terminal markings for auxiliary and control circuits - Part 1: Disconnectors and earthing switches for rated voltages52 kV) |
DIN 43456-2-2000 |
辅助和控制电路用端子标识.第2部分:额定电压≥52kV用断路器 |
(Terminal markings for auxiliary and control circuits - Part 2: Circuit breakers for rated voltages52 kV) |
DIN 43458-2000 |
手工操作或机器操作的耦合额定电压等于或大于52KW的负载断路开关和接地开关 |
(Disconnectors, earthing switches and load break disconnectors with rated voltage52 kV - Coupling for hand operation of motor-operated mechanisms) |
DIN 43459-2004 |
高压设备的燃气连接用连接装置.尺寸和要求 |
|
DIN 43460-1998 |
插塞连接器的接线图.测量电压小于52kV的断路器.辅助电流电路和控制电流电路的配置 |
(Contact occupation of plug connectors - Circuit breakers, rated voltage52 kV - Coordination of auxiliary and control-circuits) |
DIN 435-2000 |
工型梁用方楔形垫圈 |
(Square taper washers for I-sections) |
DIN 43530-1-1987 |
蓄电池.电解质和再充水.总则 |
(Accumulators; electrolyte and refilling water; general) |
DIN 43530-2-1987 |
蓄电池.电解质和再充水.铅蓄电池用电解质 |
(Accumulators; electrolyte and refilling water; electrolyte for lead acid batteries) |
DIN 43530-4-1987 |
蓄电池.电解质和再充水.铅蓄电池和碱性蓄电池用水和再充水 |
(Accumulators; electrolyte and refilling water; water and refilling water lead acid batteries and alkaline batteries) |
DIN 43531-1998 |
铅酸蓄电池.带较少维护结构电池的地面运输工具用48V驱动蓄电池.尺寸.重量.电气数据 |
(Lead-acid batteries - Traction batteries 48 V for industrial trucks with low maintenance cells - Dimensions, weights, electrical characteristics) |
DIN 43532-1986 |
铅酸蓄电池.催化剂液孔塞(再化合栓) |
(Lead-acid storage batteries; vent plug with catalyst) |
DIN 43534-1983 |
铅酸蓄电池.无需维护.带格网板与规定电解液的封闭式蓄电池.容量.电压.主要尺寸.结构特点.要求 |
(Lead storage batteries; maintenance-free, sealed, immobilized electrolyte; rated capacities, voltages, main dimensions, construction-details, requirements) |
DIN 43535-1998 |
铅酸蓄电池.带较少维护结构电池的地面运输工具用24V驱动蓄电池.尺寸.重量.电气数据 |
(Lead-acid batteries - Traction batteries 24 V with low-maintenance cells for industrial trucks - Dimensions, weights, electrical characteristics) |
DIN 43536-1998 |
铅酸蓄电池.带较少维护结构电池的地面运输工具用80V驱动蓄电池.尺寸.重量.电气数据 |
(Lead-acid batteries - Traction batteries 80 V for industrial trucks with low maintenance cells - Dimensions, weights, electrical characteristics) |
DIN 43538-1982 |
铅酸蓄电池.电动车辆用牵引电动机用蓄电池.不需维护型电池组.额定容量.主要尺寸 |
(Monobloc batteries for electric vehicles; low maintenance types, rated capacities, main dimensions) |
DIN 43539-14-1985 |
蓄电池.检验.固定型蓄电池单体和电池组.镍镉电池 |
(Accumulators; tests; stationary storage cells and batteries; Nickel-Cadmium-accumulators) |
DIN 43539-5-1984 |
蓄电池.检验.采用板栅极板和不流动电解液的免维护密封铅蓄电池 |
(Accumulators; tests; sealed lead storage batteries with grid type plates and immobilized electrolyte, maintenance free; test methods) |
DIN 43547-1971 |
光出瞳为105mm的聚光灯.主要尺寸和安装尺寸 |
(Search-light, diameter 105 mm; main and connection dimensions) |
DIN 43549-1982 |
电瓶车电气部件和电线的标记 |
(Designation of electrical items and cables for battery-powered industrial trucks) |
DIN 43560-1-1981 |
电动地面运输工具的熔断器.80V片状熔断器 |
(Fuses for battery powered industrial trucks; fuse-links 80 V) |
DIN 43579-1-1981 |
铅酸蓄电池.火车照明用电池.电池组 |
(Train-lighting batteries, block compound-batteries) |
DIN 43579-2-1981 |
铅酸蓄电池.火车照明用电池.多格电池壳 |
(Train lighting batteries, block containers) |
DIN 43579-3-1984 |
铅酸蓄电池.火车照明用电池.接线端子 |
(Lead-acid storage batteries; train lighting batteries; connecting terminals) |
DIN 43579-4-1984 |
铅酸蓄电池.火车照明用电池.支架结构电池 |
(Lead-acid storage batteries; train-lighting batteries; carrier-type battery) |
DIN 43579-5-1984 |
铅酸蓄电池.火车照明用电池.支架 |
(Lead-acid storage batteries; train lighting batteries; carrier) |
DIN 43579-6-1985 |
铅酸蓄电池.火车照明用电池.铭牌.尺寸.印字 |
(Lead-acid storage batteries; train-lighting batteries; name plate; dimensions, inscription) |
DIN 43582-1-1981 |
铅酸蓄电池.有轨车辆用有装甲板槽的照明蓄电池.26V蓄电池组.容量.主要尺寸.重量 |
(Train-lighting batteries, block compound-batteries) |
DIN 43582-2-1975 |
铅酸蓄电池.有轨车辆用有装甲板槽的照明蓄电池.多格电池盒 |
(Train-lighting batteries; block containers) |
DIN 43585-1-1966 |
无轨电瓶车用250A.80V.单极插接装置.正极 |
(1-pol. plug connection, 250 A, 80 V, for battery powered industrial trucks) |
DIN 43585-2-1966 |
无轨电瓶车用250A.80V.单极插接装置.负极 |
(1-pol. plug connection, 250 A, 80 V, for battery powered industrial trucks) |
DIN 43589-1-1994 |
地面电动运输工具用160和320A.150V的仪器插接装置.第1部分:连接尺寸.材料.标识 |
(Connector for battery powered industrial trucks 80, 160, 320 A, 150 V - Part 1: Connecting dimensions, material, marking) |
DIN 43590-1-1990 |
铅酸蓄电池.大型起动蓄电池.主要尺寸.电压.重量 |
(Lead-acid batteries; monobloc-batteries for starting internal combustion engines; main dimensions, voltages, weights) |
DIN 43590-2-1990 |
铅酸蓄电池.大型起动蓄电池.电池组箱 |
(Lead-acid batteries; monobloc-batteries for starting internal combustion engines; monobloc containers) |
DIN 43590-3-1990 |
铅酸蓄电池.大型起动蓄电池.接线夹和电缆终端 |
(Lead-acid batteries; monobloc-batteries for starting internal; combustion engines; connection terminal and cable socket) |
DIN 43593-1969 |
铅酸蓄电池.车辆蓄电池的型号标牌 |
(Lead-acid and alkaline batteries; type plate for traction batteries) |
DIN 43598-1-1993 |
铅酸蓄电池.6V和12V牵引用蓄电池.匣式板极单壳蓄电池.额定功率、主要尺寸、重量 |
(Lead-acid traction batteries 6 V and 12 V; monobloc batteries with tubular positive plates; nominal capacities, main dimensions, weights) |
DIN 436-1990 |
优先用于木结构的方垫圈 |
(Square washers for use in timber constructions) |
DIN 43600-1980 |
开关设备和互感器用运送滚轮 |
(Rollers for switchgear and instrument transformers) |
DIN 43601-1987 |
配电设备和仪用互感器运输滚轮的中心距和轨距 |
(Centerline spacings and rail gauges for rollers of switchgear and instrument transformers) |
DIN 43607-1986 |
室内设备用三极隔离开关和负荷隔离开关.额定电压12至35KV.额定电流400至1250A.主要尺寸 |
(Three-pole disconnectors and switch-disconnectors for indoor switchgear; rated voltage 12 kV up to 36 kV; rated normal current 400 A up to 1250 A; main dimensions) |
DIN 43609-1978 |
电压开关设备.压缩空气线路图的图形符号 |
(Switchgear-plants; symbols for pressure-gas diagrams) |
DIN 43614-1-1979 |
电气开关设备.压缩空气管道用管.铜管.要求 |
(Switchgear and controlgear conduits for pressure-gas pipelines; copper conduits) |
DIN 43614-2-1980 |
电气开关设备.压缩空气管道用管.不锈钢管.要求 |
(Switchgear and controlgear; conduits for pressure-gas pipelines, stainless steel conduits) |
DIN 43615-1976 |
电气开关设备.压缩空气设备的额定压力和压力范围 |
(Switchgear-plants; nominal pressure and pressure ranges for pressure-gas plants) |
DIN 43620-1-1984 |
带刀口接触的低压高功率熔断器交流电压500V和660V.直流电压400V用的低压大功率熔丝 |
(Low-voltage high-rupturing-capacity fuses with blade contacts; LV HRC fuse links for 500 and 660 V a.c. and 440 V d.c.) |
DIN 43620-3-1984 |
带刀口接触的低压高功率熔断器.交流电压500V和660V.直流电压440V用低压大功率熔丝的熔断器底座 |
(Low-voltage high-rupturing-capacity fuses with blade contacts; LV HRC fuse bases for LV HRC fuse links for 500 and 660 V a.c. and 440 V d.c.) |
DIN 43620-4-1981 |
带刀口接触的低压高功率熔断器交流电压500V和660V.直流440V.数值从00至3的低压高功率灯断器插装式手柄的装 |
(Low-voltage high-rupturing-capacity fuses with blade contacts 500 and 660 V a.c. and 440 d.c.; replacement handle for the sizes 00 up to 3; dimensions of the engaging part) |
DIN 43620-6-1987 |
带刀口触头的低压高功率熔断器.NH-滑动保险装置下部.NH-滑动保险装置分离器和用于装配的小于AC660V汇流排上 |
(Low-voltage high-rupturing-capacity fuses with blade contacts; bus-mounting fuse-bases, LV HRC bus-mounting fuse-disconnectors and LV HRC bus-mounting fuse-switches up to AC 660 V) |
DIN 43623-1981 |
固定在母线上的3极660V..100至630A低压高功率熔断器底座架 |
(Three-pole fuse-base racks 660 V, 100 to 630 A, for L.V.H.R.C. fuses, for busbar mounting) |
DIN 43624-1971 |
高压熔断器.额定电压3/3.6至30/36KV单极熔断器底座 |
(High-voltage fuses, rated voltages 3,6 to 36 kV; single-pole fuse-bases) |
DIN 43625-1983 |
高压熔断器.额定电压3.6至36KV.熔断体尺寸 |
(High-voltage fuses; rated voltages 3,6 to 36 kV; fuse-links) |
DIN 43627-1992 |
规格00-100A500V和规格1-250A500VNH型熔断器用电缆用户分线盒 |
(House connection boxes for underground service for HRC-fuses size 00 up to 100 A 500 V and size 1 up to 250 A 500 V) |
DIN 43627-3-1998 |
电缆用户分线盒.规格00-100A500V和规格1-250A500VNH型装在墙里的熔断器用电缆用户分线盒 |
(House connection boxes for underground service - Flush-type house connection boxes for underground service for HRC-fuses size 00 up to 100 A 500 V and size 1 up to 250 A 500 V) |
DIN 43628-1998 |
电线熔断保险器用熔断器盒 |
(Fuseboxes for cable protection fuses) |
DIN 43629-1-1978 |
电缆配电箱.外壳.安装尺寸 |
(Cable distribution cubicle; cabinet, mounting dimensions) |
DIN 43629-2-1978 |
电缆配电箱.安装尺寸 |
(Cable distribution cubicle; base, mounting dimensions) |
DIN 43629-3-1982 |
电缆配电箱.内部结构安装尺寸 |
(Cable distribution cubicle; internal construction; mounting dimensions) |
DIN 43633-1-1991 |
旋转隔离开关.额定电压123kV.连接尺寸和固定尺寸.配置 |
(Two-column (centre-break) disconnector; rated voltage 123 kV; terminal and mounting dimensions, layout) |
DIN 43633-2-1988 |
旋转隔离开关.额定电压245KV.连接尺寸和固定尺寸.配置 |
(Two-column (centre-break) disconnector; rated voltage 245 kV; terminal and mounting dimensions, layout) |
DIN 43636-1992 |
架空线穿房连接接线盒.HRC熔断器规格为0~100A500V用接线盒 |
(Overhead-line house connection boxes for HRC-fuses size 00 up to 100 A 500 V) |
DIN 43636-2-1992 |
规格00-100A500VHN熔断器用架空线用户分线盒 |
(Overhead-line house connection boxes for HRC-fuses size 00 up to 100 A 500 V) |
DIN 43637-2-1961 |
架空线路专用转接盒(防护系统P43) |
(Overhead-line private connection frames (protective system P 43)) |
DIN 43637-4-1992 |
规格00-100A500V和规格1-250A500VNH型熔断器用架空线用户分线盒 |
(Overhead-line house connection boxes for HRC-fuses size 00 up to 100 A 500 V and size 1 up to 250 A 500 V) |
DIN 43637-5-1977 |
架空线路用户转接盒.屋顶支架管中导线隔离用隔片 |
(Overhead line private connection boxes; disk for spacing of conductors in the roof pole stand tube) |
DIN 43649-1985 |
起重磁铁的功率铭牌.文字说明 |
(Rating plates for lifting magnets; marking data) |
DIN 43653-1976 |
半导体整流器用尺寸为1至3和00带旋片的大功率熔断器 |
(High rupturing-capacity fuses for semi-conductor converters) |
DIN 43655-1969 |
带2:1轴线的双对数纸 |
(Forms of double logarithmic paper with scales in the ratio 2/1) |
DIN 43656-1979 |
室内电气开关设备和36KV以下高压开关设备.识别颜色 |
(Indoor switchgear and controlgear assemblies and high-voltage switchgear and controlgear up to 36 kV; colouring) |
DIN 43658-1977 |
户外开关设备的自由尺寸公差 |
(General tolerances for outdoor substations) |
DIN 43660-1982 |
电气开关设备的模数序列 |
(Modular order for electrical switchgear and controlgear installations) |
DIN 43661-1972 |
户内电工设备用槽钢;设计与安装 |
(Foundation bars for indoor switchgear; design and mounting particulars) |
DIN 43668-1964 |
电气开关设备的匣门或柜门钥匙.双头钥匙 |
(Key for the doors of electrical switchgear cubicles and cabinets; double-bit key) |
DIN 43670-1975 |
铝汇流排.持续电流的测量 |
Aluminium bus bars; design for continuous current |
DIN 43670-2-1985 |
铝汇流排.铜外壳.持续电流的测量 |
Aluminium bus bars copper cladding; design for continuous current |
DIN 43671-1975 |
铜汇流排.持续电流的测量 |
(Copper bus bars; design for continuous current) |
DIN 43673-1-1982 |
电流母线钻孔和螺栓紧固.矩形横截面的电流母线 |
Drilled holes and screw connections for busbars; Rectangular cross section busbars |
DIN 43673-2-1982 |
电流母线钻孔和螺栓紧固.U-横截面的电流母线 |
(Drilled holes and screw connections for busbars; Channel section busbars) |
DIN 43675-1-1975 |
连接螺栓用连接件.400-3150A小于60KV的变压器引线和穿墙引线的扁连接件 |
(Rectangular-section connectors for terminal studs rated between 400 and 3150 A for power transformer- and wallbushings below 60 kV) |
DIN 43675-2-1984 |
柱螺栓用连接件.户外变压器套管的扁连接件.Um24和36KV.5和8kA |
(Connectors for terminal studs; flat connectors for outdoor transformer bushings; U 24 and 36 kV, 5 and 8 kA) |
DIN 43675-3-1975 |
3150A以上的发电机引线连接螺栓用连接件 |
(Rectangular-section connectors for terminal studs rated over, 3150 A, for alternator-bushings) |
DIN 43675-4-1977 |
连接螺栓用连接件.10KA以上发电机引线用八角连接件 |
(Octagon connectors for terminal studs, rated over 10000 A, for alternator-bushings) |
DIN 43675-5-1979 |
连接螺栓用连接件.10KA以上变压器引线用八角连接件 |
(Octagon connectors for terminal studs, rated over 10000 A, for transformer-bushings) |
DIN 43683-1980 |
电气开关设备内导线排列顺序 |
(Sequence of conductors in electrical switchgear assemblies) |
DIN 43684-1969 |
开关设备.方格图.格中心距 |
(Mosaic tile mimic diagram; centre distances) |
DIN 43686-1977 |
电气开关设备中压缩空气发生装置用球形压力容器 |
(Pressure vessels for air generating stations in electrical switching plants) |
DIN 43687-1976 |
电气开关设备中64巴以下压缩空气发生装置用立式压力容器.容量.主要尺寸和安装尺寸 |
(Vertical pressure tanks for air pressure generating stations in electrical switching plants) |
DIN 43688-1976 |
电气开关设备中64巴以下压缩空气发生装置用卧式压力容器.容量.主要尺寸和安装尺寸 |
(Horizontal pressure tanks for air pressure generating stations in electrical switching plants) |
DIN 43689-1977 |
电气开关设备中空压装置用断流阀.公称压力40和60 |
(Shut-off valves 40 (570 psig) and 64 (911 psig) for compressed-air installations in electrical switching plants) |
DIN 43690-1980 |
电气开关设备中压缩空气发生装置用空压机.要求 |
(Air compressors for compressed-air generating plants in electrical switchgears; requirements) |
DIN 43691-1982 |
电气开关设备.压力.概念 |
(Electrical switchgear; pressure; expressions) |
DIN 43693-1982 |
低压开关设备.拉杆定位开关.扁平封闭型.安装和结构尺寸 |
(Low-voltage switchgear and controlgear; position switches with, flat design, encapsulated; functional and mounting dimensions) |
DIN 43697-1982 |
低压开关设备.定位开关系列 |
(Low voltage switchgear and controlgear; Multi-positon switches) |
DIN 43700-1982 |
测量.控制.调节.安装在平板上的测量.控制.调节仪表.公称和截面尺寸 |
(Measurement and control; measurement and control instruments for panel mounting; nominal front- and cut-out-dimensions) |
DIN 43718-1987 |
测量.控制.调节.指示测量仪表的正面框架.主要尺寸 |
(Measurement and control; front-frames and frontpanels of measurement and control equipment; principal dimensions) |
DIN 43719-1990 |
测量.控制.调节.MSR仪器安装用机械光栅系统 |
(Measurement and control; mechanical grid system for the installation of measuring and control instruments) |
DIN 43722-1994 |
热电偶.第3部分:加长电缆和补偿电缆.容差和鉴定系统 |
(Thermocouples; part 3: extension and compensating cables; tolerances and identification system (IEC 60584-3:1989, modified); German version HD 446.3 S1:1993) |
DIN 43724-1979 |
测量.控制.调节.电测温计.热电偶的陶瓷保护套管和夹环 |
(Electrical temperature sensors; ceramic protecting tubes and holding rings for thermocouple thermometers) |
DIN 43729-1978 |
测量.控制.调节.电测温计.热电偶和电阻温度计用接线头 |
(Electrical temperature sensors; connection heads for thermocouple-thermometers and resistance-thermometers) |
DIN 43732-1986 |
测量.控制.调节.电温度感受器.热电偶温度计用热电偶 |
(Measurement and control; electrical temperature sensors; thermocouples for thermocouple thermometers) |
DIN 43733-1986 |
测量.控制.调节.电温度感受器.无可置换测件的热电偶温度计 |
(Measurement and control; electrical temperature sensors; straight thermocouple thermometers without interchangeable sensor units) |
DIN 43734-1986 |
测量.控制.调节.电温度感受器.热电偶温度计和电阻温度计用法兰挡板 |
(Measurement and control; electrical temperature sensors; stop flanges for thermocouple thermometers and resistance thermometers) |
DIN 43735-1986 |
测量.控制.调节.电温度感受器.热电偶温度计用传感件 |
(Measurement and control; electrical temperature sensors; Sensor units for thermocouple thermometers) |
DIN 43743-1977 |
测量用稳压电源;概念.参数说明与检验 |
(Stabilized supply apparatus for measurement; definitions, expression and testing of performance) |
DIN 43751-1-1987 |
测量.控制.调节.数字式测量仪表.概念.检验.数据说明的一般规定 |
(Measurement and control; digital measuring instruments; general specifications relating to definitions, tests and data sheet details) |
DIN 43751-2-1987 |
测量.控制.调节.数字式测量仪表.测试模拟量的测量仪表.概念.检验和数据说明 |
(Measurement and control; digital measuring instruments; instruments for measuring analogue quantities; definitions, tests and data sheet details) |
DIN 43751-3-1987 |
测量.控制.调节.数字式测量仪表.测量数字量值的仪表.概念.检验和数据说明 |
(Measurement and control; digital measuring instruments; instruments for measuring digital quantities; definitions, tests and data sheet details) |
DIN 43751-4-1990 |
测量.控制.调节.数字式测量仪表.测量时间基准量的仪器.概念.检验和数据单说明 |
(Measurement and control; digital measuring instruments; instruments for measuring time reference quantities; definitions, tests and data sheet details) |
DIN 43762-1986 |
测量.控制.调节.电温度感受器.电阻温度计用传感件 |
(Measurement and control; electrical temperature sensors; sensor units for resistance thermometers) |