标准号 |
中文名称 |
英文名称 |
DIN 46200-1977 |
1·6KA以下导电连接螺栓.电流强度的配置和设计 |
(Current carrying connection bolts up to 1600 A; design and assignment of current intensities) |
DIN 46202-1987 |
52KV以上配电开关和控制器.仪表用互感器.以及避雷用连接螺栓 |
(Terminal studs for switchgear and controlgear, instrument transformers and surge arresters of 52 kV and above) |
DIN 46206-1-1985 |
电气设备的连接.70m2以下圆形铜导线连接的扁端子 |
(Terminals for electrical equipment; flat blade terminals for the connection of round copper conductors up to 70 mm) |
DIN 46206-2-1971 |
电气设备的连接.大于或等于40A平面连接.主要尺寸和配置 |
(Supply-terminals for electrical equipment40 A; connections with rectangular cross-section, basic dimensions and coordination) |
DIN 46206-3-1983 |
电气设备的连接.52kV以上设备的平面连接.主要尺寸.配置 |
(Terminals for electrical equipment; flat terminals for equipment from and above 52 kV; basic dimensions, coordination) |
DIN 46207-1971 |
电气设备的连接.插孔与开口连接.主要尺寸和配置 |
(Connections for Electrical Devices; Sleeve Terminals and Side Opening Sleeve Terminals; Principal Dimensions and Correlation) |
DIN 4621-1995 |
叠板弹簧.弹簧夹 |
(Laminated leaf springs - Alignment clips) |
DIN 46211-1965 |
铜导线用冲压电缆终端孔 |
(Stamped Cable Sockets for Copper Conductors) |
DIN 46215-1976 |
冲压带孔焊片 |
(Stamped solder lugs, with hole) |
DIN 46216-1976 |
冲压带槽焊片 |
(Stamped solder lugs, with slot) |
DIN 46218-1966 |
冲孔线端连接耳.冕状 |
(Stamped metal rings for conductors) |
DIN 46220-1965 |
铜导线用冲压件.浇铸的直式电缆套(端子) |
(Cable sockets, hot pressed, cast for copper conductors) |
DIN 46221-1965 |
铜导线用冲压件.浇铸的角式电缆终端 |
(Angle sockets, hot pressed, cast for copper conductors) |
DIN 46223-1973 |
圆形端子 |
(Round-terminals) |
DIN 46224-1982 |
碳刷用铜电缆的冲压终端 |
(Stamped cable sockets for flexibles of carbon brushes) |
DIN 46225-1976 |
绝缘导线用带绝缘套的冲压爪形电缆终端 |
(Stamped terminals with embrace of the insulation for insulated cables) |
DIN 46227-1960 |
铜导线用电缆终端夹子 |
(Cable clamp sockets for copper conductors) |
DIN 46228-1-1992 |
芯线终端套.无塑料套的管形套 |
(Tubular end-sleeves without plastic sleeve) |
DIN 46228-2-1992 |
芯线终端套管.带及不带绝缘包皮的压接结构 |
(Crimp-type end-splices, with and without insulation grip) |
DIN 46228-3-1992 |
芯线终端套管.导线包皮.无绝缘包皮 |
(Conductor-embracing end-splices, without insulation grip) |
DIN 46228-4-1990 |
芯线终端套.带塑料套的管头 |
(Tubular end-sleeves with plastic sleeve) |
DIN 46229-1980 |
电缆终端.连接端的命名 |
(Terminal ends; terms) |
DIN 46230-1980 |
无绝缘套非焊接铜销钉型电缆端子 |
(Terminal ends for solderless connections; pin type, without insulating sleeve, for copper conductors) |
DIN 46231-1970 |
铜导线用绝缘的无焊点连接销钉形电缆终端 |
(Pin type cable-sockets for solderless connections, insulated, for copper conductors) |
DIN 46234-1980 |
铜导线用无绝缘套的无焊点连接环形电缆终端 |
(Terminal ends for solderless connections; ring type, without insulating sleeve, for copper conductors) |
DIN 46235-1983 |
铜导线用压接件鱼尾板形电缆终端 |
(Cable lugs; for compression connections, cover plate type, for copper conductors) |
DIN 46236-1964 |
供钎焊用的冲压带绝缘套的爪形电缆终端 |
(Stamped cable sockets with embrace of the insulation) |
DIN 46237-1970 |
铜导线用绝缘的无焊点连接的挤压电缆终端 |
(Crimp-type cable sockets for solderless connections, insulated, for copper conductors) |
DIN 46238-1985 |
塑料绝缘通信软线的弹簧电缆终端 |
(Springterminals for plastic insulated telecommunication cords) |
DIN 46244-1980 |
仪器扁插头用插孔 |
(Tabs for receptacles) |
DIN 46244-2-1987 |
仪器用扁插头.槽型结构 |
(Slit tab attached to equipment) |
DIN 46245-1-1977 |
插头宽度为2·8的带绝缘套的插套 |
(Receptacles for tab size 2,8, with insulating sleeve) |
DIN 46245-2-1976 |
插头宽度为4·8的带绝缘套的插套 |
(Receptacles for tabs size 4,8, with insulating sleeve) |
DIN 46245-3-1975 |
插头宽度为6·3的带绝缘套的插套 |
(Receptacles for tabs size 6,3, with insulating sleeve) |
DIN 46247-1-1975 |
插头宽度为2·8的无绝缘套的插套 |
(Receptacles for tabs size 2,8, without insulating sleeve) |
DIN 46247-2-1973 |
插头宽度为4·8的无绝缘套的插套 |
(Receptacles for tabs size 4,8, without insulating sleeve) |
DIN 46247-3-1973 |
插头宽度为6·3的无绝缘套的插套 |
(Receptacles for tabs size 6,3, without insulating sleeve) |
DIN 46247-4-1973 |
插头宽度为9·5的无绝缘套的插套 |
(Receptacles for tabs size 9,5, without insulating sleeve) |
DIN 46248-3-1976 |
无绝缘套的扁形插头.插头宽度为6·3 |
(Tab, without insulating sleeve, width of tab 6,3) |
DIN 46249-1-1980 |
非绝缘平面插塞连接.要求和检验 |
(Snap-on connectors, non insulated; requirements, tests) |
DIN 46252-1975 |
带塑料绝缘套的通信软线用电缆终端 |
(Terminals for plastic insulated telecommunication cords) |
DIN 46254-1-1982 |
通信绞线的非钎焊连接.压接.要求.检验 |
(Solderless connections for telecommunication cords crimp connections; requirements, test methods) |
DIN 46257-1975 |
电缆终端.带织物和橡胶绝缘的通信软线用连接管 |
(Sockets, connecting sleeve for telecommunication cords) |
DIN 4626-1986 |
叠层板簧.中心螺栓 |
(Center bolts for laminated leaf springs) |
DIN 46260-1-1988 |
低压用螺栓接线柱.组装 |
(Low-voltage stud-terminals; compilation) |
DIN 46260-2-1988 |
低压用螺栓接线柱.零件表 |
(Low-voltage stud-terminals; part list) |
DIN 46262-1-1988 |
低压用螺栓接线柱.绝缘子 |
(Low-voltage stud-terminals; insulators) |
DIN 46262-2-1988 |
低压用螺栓接线柱.套管螺栓 |
(Low-voltage stud-terminals; bushing studs) |
DIN 46262-4-1988 |
低压用螺栓接线柱.环.卡圈.垫圈.底板 |
(Low-voltage stud-terminals; snap rings, shackles, washers, shims) |
DIN 46264-1988 |
高压用带浇注树脂绝缘件的引线端子 |
(High-voltage feed-through terminals with cast resin insulator) |
DIN 46265-1-1988 |
高压用带陶瓷绝缘体的引线端子.组装 |
(High-voltage feed-through terminals with ceramic insulator; compilation) |
DIN 46265-2-1988 |
高压用带陶瓷绝缘体的引线端子.零件表 |
(High-voltage feed-through terminals with ceramic insulator; parts list) |
DIN 46266-1-1988 |
高压用引线端子.陶瓷绝缘子 |
(High-voltage feed-through terminals; ceramic insulator) |
DIN 46266-2-1988 |
高压用引线端子.引线接线柱 |
(High-voltage feed-through terminals; bushing studs) |
DIN 46266-3-1988 |
高压用引线端子.凸缘.垫圈 |
(High-voltage feed-through terminals; flanges, washers) |
DIN 46267-1-1985 |
铜导体用不耐张力的压制接头 |
(Non tension-proof compression joints for copper conductors) |
DIN 46267-2-1985 |
铝导体用不耐张力的压制接头 |
(Non tension-proof compression joints for aluminium conductors) |
DIN 46268-1-1988 |
圆插接件.3.5mm圆插头用带卡簧的圆插座 |
(Circular connectors; snap-in receptacle for 3,5 mm snap-in pin) |
DIN 46268-2-1988 |
圆插接件.3.5mm圆插座用带卡簧的圆插座 |
(Circular connectors; snap-in pin for 3,5 mm snap-in receptacles) |
DIN 46274-1973 |
同轴端子B |
(Sleeve terminals B) |
DIN 46276-1-1991 |
开关设备.母线和扁接头用的膨胀接头.层状的.韧性的 |
(Expansion joints for busbars and flat terminals; lamellar flexible) |
DIN 46276-2-1991 |
开关设备.母线和扁接头用的膨胀接头.层状的.高韧性的 |
(Expansion joints for busbars and flat terminals; lamellar high flexible) |
DIN 46278-1952 |
通用部件.开关设备接线板.用于100mm2以下单根导线的接线板 |
(General components; series terminal in switchboard plants, series terminal for a conductor up to 10 mm) |
DIN 46278-2-1965 |
有轨车辆用接线板.用于1.5-120mm2平方导线 |
(Mountable terminal blocks for traction equipment for conductors from 1,5 mm up to 120 mm) |
DIN 46281-1976 |
防爆装置用扁平接线板.用于2.5mm2以下的导线.直流600V.交流500V.10A |
(Flat terminal connection strips for electrical apparatus in firedamp proof and explosion protected enclosures) |
DIN 46282-1973 |
导线接头的接线夹子 |
(Clamping saddle for conductors) |
DIN 46284-1972 |
交流380V直流440V.2.5mm2平方以下导线的二极和三极盒式端子板(仪器端子) |
(Two- and three-pole socket terminal strips (appliance terminals) 380 V a.c. and 440 V d.c. for conductors up to 2,5 mm) |
DIN 46285-1972 |
交流380V直流440V.2.5MM2平方以下导线的二极至三极盒式端子板(灯具端子) |
(One to three-pole socket terminal strips (lighting fixture terminals) 380 V a.c. and 440 V d.c. for conductors up to 2,5 mm) |
DIN 46288-1974 |
导线接头用连接垫圈 |
(Connecting Washers for Conductors) |
DIN 46289-1-1984 |
电气端子.分类.概念.专业词汇 |
(Terminals for electrical purposes; classification, definitions, technical terms) |
DIN 46294-1985 |
带有6个接线柱的矩形端子板.主要尺寸 |
(Terminal board, square shaped with six terminals; main dimensions) |
DIN 46295-1-1985 |
带有6个槽接线柱的矩形端子板.主要尺寸 |
(Terminal board, square shaped with six slit-bolts; main dimensions) |
DIN 46295-2-1981 |
带有6个槽接线柱的矩形端子板.桥形连接片和压紧螺母 |
(Terminal board, square shaped with six slit-bolts; accessories) |
DIN 46295-3-1981 |
带有6个槽接线柱的矩形端子板.电缆接孔 |
(Terminal board, square shaped with six slit-bolts; cable sockets) |
DIN 46300-1980 |
安装材料.把电度表和控制仪固定在电表底盘上的固定螺栓 |
(Mounting material; mounting bolt for electric meters and controlgear on meter panels) |
DIN 46329-1983 |
铝导线用环形压制连接的电缆终端 |
(Cable lugs; for compression connections, ring type, for aluminium conductors) |
DIN 46330-1-1981 |
插头宽度为2·4的无绝缘套的短插套 |
(Short receptacles without insulating sleeve, for tab size 2,4) |
DIN 46330-2-1981 |
插头宽度为2·8的无绝缘套的短插套 |
(Short receptacles; without insulating sleeve, for tab size 2,8) |
DIN 46335-1978 |
带塑料绝缘套或编织物绝缘套的通信软线用电缆终端 |
(Terminals for plastic- or textil insulated telecommunication cords) |
DIN 46336-1987 |
弹簧电缆终端用插头外壳 |
(Plugbox for springterminals) |
DIN 46339-1984 |
接线板上测试用的带弹性销钉的接插件.插头和插座的主要尺寸 |
(Connectors with resilient pin for testing purposes on terminal blocks; main dimensions for plug and socket) |
DIN 46340-1-1981 |
插头宽度为2·8的快速插套 |
(Snap-in receptacles for tab size 2,8) |
DIN 46340-3-1981 |
插头宽度为6·3的快速插套 |
(Snap-in receptacles for tab size 6,3) |
DIN 46340-4-1981 |
插头宽度为9·5的快速插套 |
(Snap-in receptacles for tab size 9,5) |
DIN 46340-5-1981 |
插头宽度为7·8的快速插套 |
(Snap-in receptacles for tab size 7,7) |
DIN 46341-1-1977 |
铜导线用无绝缘套的非焊接连接的接线器 |
(Solderless connectors, without insulating sleeve, for copper conductors) |
DIN 46342-1-1973 |
带直形和角形固定孔的扁插头用插套 |
(Tabs, straight and angled, for receptacles) |
DIN 46343-1-1981 |
插套尺寸为2·8的带簧片的扁插头 |
(Snap-in tabs for receptacle size 2,8) |
DIN 46343-2-1981 |
插座尺寸为4.8的带簧片的扁插头 |
(Snap-in tabs for receptacle size 4,8) |
DIN 46343-3-1981 |
插座尺寸为6.3的带簧片的扁插头 |
(Snap-in tabs for receptacle size 6,3) |
DIN 46343-4-1981 |
插座尺寸为9.5的带簧片的扁插头 |
(Snap-in tabs for receptacle size 9,5) |
DIN 46345-1980 |
插头宽度为6·3的带扁插头的插套 |
(Receptacles with tab for size 6,3) |
DIN 46346-1980 |
插头宽度为6·3侧面接线的插套 |
(Flag receptables for tab size 6,3) |
DIN 46380-2002 |
电缆和电线的生产及运输.定义 |
(Manufacturing and transport of cables and wires - Definitions) |
DIN 46391-1-1979 |
电缆.电线的交货用的绕线盘.尺寸 |
(Delivery drums) |
DIN 46391-2-1981 |
电缆.电线的交货用的绕线盘.木质绕线盘的交货技术条件 |
(Delivery drums; technical terms of delivery for wooden drums) |
DIN 46391-3-1984 |
电缆.电线的交货用的绕线盘.具有大于2800mm的法兰直径的线盘.尺寸 |
(Delivery drums; diameter above 2800 mm) |
DIN 46391-4-1985 |
电缆.导线的交货用的绕线盘.刚绕线盘的交货技术条件 |
(Delivery drums; technical terms of delivery for steel drums) |
DIN 46392-1-1981 |
绝缘导线交货用线盘.尺寸 |
(Spools; for the delivery of flexible cords, dimensions) |
DIN 46395-1972 |
机用线圈 |
(Machine spools) |
DIN 46396-2-1986 |
电缆.电线生产用容器外壳内径为500mm以上 |
(Containers for use in the manufacture of cables and wires, inner diameter above 500 mm) |
DIN 46397-11-2005 |
用于线材制造的绕线盘.第11部分:带矩形法兰的绕线盘.尺寸 |
|
DIN 46397-11-2005 |
用于线材制造的绕线盘.第11部分:带矩形法兰的绕线盘.尺寸 |
|
DIN 46397-12-2005 |
用于线材制造的绕线盘.第12部分:带矩形法兰的绕线盘.技术规范 |
|
DIN 46397-12-2005 |
用于线材制造的绕线盘.第12部分:带矩形法兰的绕线盘.技术规范 |
|
DIN 46397-1983 |
用于线材制造的绕线盘 |
(Spools for fabrication of wires) |
DIN 46397-21-2005 |
用于线材制造的绕线盘.第21部分:带锥形法兰的绕线盘.尺寸 |
|
DIN 46397-21-2005 |
用于线材制造的绕线盘.第21部分:带锥形法兰的绕线盘.尺寸 |
|
DIN 46397-22-2005 |
用于线材制造的绕线盘.第22部分:带锥形法兰的绕线盘.技术规范 |
|
DIN 46397-22-2005 |
用于线材制造的绕线盘.第22部分:带锥形法兰的绕线盘.技术规范 |
|
DIN 464-1986 |
滚花螺钉.高型 |
(Knurled thumb screws) |
DIN 46406-1-1972 |
电机用轮箍丝.可磁化的拉制镀锡钢丝 |
(Binding Wires for Electrical Machines; Magnetic Steel Wire, Drawn and Tinned) |
DIN 46406-2-1972 |
电机用轮箍丝.不可磁化的拉制镀锡钢丝 |
(Binding Wires for Electrical Machines; Non-magnetic Steel Wire, Drawn and Tinned) |
DIN 46420-1970 |
电工用拉制圆铝线.尺寸 |
(Round Aluminium Wires for Electrical Purposes, Drawn; Dimensions) |
DIN 46424-1973 |
开关设备.汇流排用压制U型铝型材 |
(Switchgear; Extruded Channel Sections of Aluminium for Busbars) |
DIN 46425-1970 |
电工用精拉制圆铝线.尺寸 |
(Round Aluminium Wires for Electrical Purposes, Exactly Drawn; Dimensions) |
DIN 46431-1970 |
电工用精拉制圆铜线.尺寸 |
(Round Copper Wires for Electrical Purposes; Precision Drawn, Dimensions) |
DIN 46438-1972 |
高柔性圆铜索 |
(Round ropes of copper; high flexible) |
DIN 46440-1972 |
编织的圆铜索 |
(Braided round ropes of copper) |
DIN 46443-1972 |
平织扁铜索 |
(Webbed flat stranded ropes of copper) |