编号 | 中文名称 | 英文名称 |
BS EN 10027-1-1992 | 钢的命名体系.第1部分:钢名.主要符号 | (Designation systems for steel - Steel names, principal symbols) |
BS EN 10027-2-1992 | 钢的命名体系.第2部分:钢号 | (Designation systems for steels - Steel numbers) |
BS EN 10028-1-2000 | 压力容器用的钢板制品规范.一般要求 | (Specification for flat products made of steels for pressure purposes - General requirements) |
BS EN 10028-2-2003 | 压力容器用的扁平钢轧材规范.具有规定的耐高温性能的非合金钢和合金钢 | (Specification for flat products made of steels for pressure purposes - Non-alloy and alloy steels with specified elevated temperature properties) |
BS EN 10028-3-2003 | 压力容器用的扁平钢轧材规范.经过正火处理的可焊细粒钢 | (Specification for flat products made of steels for pressure purposes - Weldable fine grain steels, normalized) |
BS EN 10028-4-2003 | 压力容器用的扁平钢轧材规范.具有规定的低温特性的镍合金钢 | (Specification for flat products made of steels for pressure purposes - Nickel alloy steels with specified low temperature properties) |
BS EN 10028-5-2003 | 压力容器用的扁平钢轧材规范.热机滚轧可焊细粒钢 | (Specification for flat products made of steels for pressure purposes - Weldable fine grain steels, thermomechanically rolled) |
BS EN 10028-6-2003 | 压力用的扁平钢轧材规范.淬火和回火可焊细粒钢 | (Specification for flat products made of steels for pressure purposes - Weldable fine grain steels, quenched and tempered) |
BS EN 10028-7-2000 | 压力容器用的钢板制品规范.不锈钢 | (Specification for flat products made of steels for pressure purposes - Stainless steels) |
BS EN 10029-1991 | 厚度3mm或3mm以上热轧钢板尺寸、形状和质量公差规范 | (Specification for tolerances on dimensions, shape and mass for hot rolled steel plates 3 mm thick or above) |
BS EN 10031-2003 | 锻造用半成品.形状和质量尺寸公差 | (Semi finished products for forging - Tolerances on dimensions shape and mass) |
BS EN 10034-1993 | 工字型和H型结构钢.形状和尺寸公差 | (Structural steel I and H sections - Tolerances on shape and dimensions) |
BS EN 10036-1991 | 黑色金属材料的化学分析.钢铁中的总碳含量的测定.在氧气中燃烧后的重力测定法 | (Chemical analysis of ferrous materials - Determination of total carbon in steels and irons - Gravimetric method after combustion in a stream of oxygen) |
BS EN 1004-2005 | 预制组件制的移动通道和工作塔.材料、尺寸、设计载荷、安全和性能要求 | |
BS EN 10045-1-1990 | 金属材料的夏比冲击试验.V形和U形切口试验方法 | (Charpy impact test on metallic materials - Test method (V- and U-notches)) |
BS EN 10045-2-1993 | 金属材料的摆式冲击试验.第2部分:冲击试验机的检验方法 | (Charpy impact test on metallic materials - Method for the verification of impact testing machines) |
BS EN 10048-1997 | 热滚轧窄钢带.尺寸和形状公差 | (Hot rolled narrow steel strip - Tolerances on dimensions and shape) |
BS EN 1005-1-2002 | 机械安全.人体特性.术语和定义 | (Safety of machinery - Human physical performance - Terms and definitions) |
BS EN 1005-2-2003 | 机械安全.人体特性.机械和机械部件的人工搬运 | (Safety of machinery - Human physical performance - Manual handling of machinery and component parts of machinery) |
BS EN 1005-3-2002 | 机械安全.人体特性.机械操作的推荐力限值 | (Safety of machinery - Human physical performance - Recommended force limits for machinery operation) |
BS EN 10051-1992 | 非合金钢和合金钢连续热轧未涂覆板材、薄板和带材规范.尺寸和形状公差 | (Specification for continuously hot-rolled uncoated plate, sheet and strip of non-alloy and alloy steels - Tolerances on dimensions and shape) |
BS EN 10052-1994 | 黑色金属制品的热处理术语词汇 | (Vocabulary of heat treatment terms for ferrous products) |
BS EN 10055-1996 | 热轧等边园弧根T型钢的尺寸和形状尺寸公差 | (Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions) |
BS EN 10056-1-1999 | 等角和非等角结构钢规范.尺寸 | (Specification for structural steel equal and unequal angles - Dimensions) |
BS EN 10056-2-1993 | 等边和不等边结构角钢.形状和尺寸公差 | (Specification for structural steel equal and unequal angles - Tolerances on shape and dimensions) |
BS EN 10058-2003 | 一般用途热轧扁钢棒.尺寸及形状和尺寸公差 | (Hot rolled flat steel bars for general purposes - Dimensions and tolerances on shape and dimensions) |
BS EN 10059-2003 | 一般用途热轧方形钢棒.尺寸及形状和尺寸公差 | (Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions) |
BS EN 10060-2003 | 一般用途热轧圆钢棒.尺寸及形状和尺寸公差 | (Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions) |
BS EN 10061-2003 | 一般用途热轧六角钢棒.尺寸及形状和尺寸公差 | (Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions) |
BS EN 10067-1997 | 热轧制球扁钢.尺寸及形状、尺寸和质量公差 | (Hot rolled bulb flats - Dimensions and tolerances on shape, dimensions and mass) |
BS EN 1007-1-2002 | 高级工业陶瓷.陶瓷复合材料.纤维增强的试验方法.胶粘剂含量的测定 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of size content) |
BS EN 1007-2-2002 | 高级工业陶瓷.陶瓷复合材料.纤维增强的试验方法.线性密度的测定 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of linear density) |
BS EN 1007-3-2003 | 高级工业陶瓷.陶瓷复合材料.增强纤维的试验方法.长纤维直径和横截面积的测定 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of filament diameter and cross-section area) |
BS EN 1007-4-2005 | 高级工业陶瓷.陶瓷复合材料.纤维增强的试验方法.环境温度下长纤维的抗拉性能测定 | |
BS EN 1007-5-2003 | 高级工业陶瓷.陶瓷复合材料.增强纤维的试验方法.室温下复丝束中长丝断开时的拉伸强度和拉伸应变分布的测定 | (Advanced technical ceramics - Ceramic composites - Methods of test for reinforcements - Determination of distribution of tensile strength and of tensile strain to failure of filaments within a multifi) |
BS EN 10071-1991 | 黑色金属材料的化学分析.钢铁中的锰含量的测定.电势滴定法 | (Chemical analysis of ferrous materials - Determination of manganese in steels and irons - Electrometric titration method) |
BS EN 10079-1993 | 钢制品定义 | (Definition of steel products) |
BS EN 1008-2002 | 混凝土的混合用水.取样、测试和评价水的适用性的规范, 包括作为混凝土混合用水的混凝土加工过程中回收的水 | (Mixing water for concrete - Specification for sampling, testing and assessing the suitability of water, including water recovered from processes in the concrete industry, as mixing water for concrete) |
BS EN 10083-1-1991 | 淬硬钢和回火钢.第1部分:特种钢供货技术条件 | (Quenched and tempered steels - Technical delivery conditions for special steels) |
BS EN 10083-2-1991 | 淬硬钢和回火钢.第2部分:非合金优质钢供货技术条件 | (Quenched and tempered steels - Technical delivery conditions for unalloyed quality steels) |
BS EN 10083-3-1996 | 淬硬钢和回火钢.第3部分:硼钢的供货技术条件 | (Quenched and tempered steels - Technical delivery conditions for boron steels) |
BS EN 10084-1998 | 表面硬化钢.技术提交条件 | (Case hardening steels - Technical delivery conditions) |
BS EN 10085-2001 | 氮化钢.技术提交条件 | (Nitriding steel - Technical delivery conditions) |
BS EN 10087-1999 | 快削钢.热轧棍和棒半成品技术提交条件. | (Free cutting steels - Technical delivery conditions for semi-finished products, hot rolled bars and rods) |
BS EN 10088-1-1995 | 不锈钢.不锈钢目录 | (Stainless steels - List of stainless steels) |
BS EN 10088-1-2005 | 不锈钢.不锈钢的清单 | |
BS EN 10088-2-1995 | 不锈钢.一般用途的薄板/板材和带材的技术交货条件 | (Stainless steels - Technical delivery conditions for sheet/plate and strip for general purposes) |
BS EN 10088-2-2005 | 不锈钢.一般用途耐腐蚀钢薄板/板材和带材的交货技术条件 | |
BS EN 10088-3-1995 | 不锈钢.一般用途的半成品、钢棒、轧制线材和型钢的技术交货条件 | (Stainless steels - Technical delivery conditions for semi-finished products, bars, rods and sections for general purposes) |
BS EN 10088-3-2005 | 不锈钢.通用耐腐蚀钢制半成品、棒材、杆材、线材、型材和光亮产品的交货技术条件 | |
BS EN 10089-2002 | 淬火和回火弹簧用热轧钢.交货技术条件 | (Hot rolled steels for quenched and tempered springs - Technical delivery conditions) |
BS EN 10090-1998 | 内燃机用阀门钢和合金 | (Valve steels and alloys for internal combustion engines) |
BS EN 10092-1-2003 | 一般用途热轧弹簧扁钢棒.尺寸及形状和尺寸公差 | (Hot rolled spring steel flat bars - Flat bars - Dimensions and tolerances on shape and dimensions) |
BS EN 10092-2-2003 | 一般用途热轧弹簧扁钢棒.有肋有槽的簧片.尺寸及形状和尺寸公差 | (Hot rolled spring steel flat bars - Ribbed and grooved spring leaves - Dimensions and tolerances on shape and dimensions) |
BS EN 10095-1999 | 耐热钢和镍合金 | (Heat resisting steels and nickel alloys) |
BS EN 1010-3-2003 | 机械安全.印刷和纸加工机械的设计和施工的安全要求.切削机 | (Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Cutting machines) |
BS EN 1010-4-2004 | 机械安全.设计和生产打印机和纸加工机的安全要求.装订机、纸加工机和装饰机 | |
BS EN 10106-1996 | 冷轧非颗粒结构定向最终退火状态下的电工钢片和钢带 | (Cold rolled non-oriented electrical steel sheet and strip delivered in the fully processed state) |
BS EN 10107-1996 | 颗粒结构定向最终退火装态下的电工钢片和钢带 | (Grain-oriented electrical steel sheet and strip delivered in the fully processed state) |
BS EN 10108-2004 | 冷锻和冷挤压圆钢棒.尺寸和公差 | |
BS EN 1011-1-1998 | 焊接.金属材料焊接的推荐规范.电弧焊接的通用指南 | (Welding - Recommendations for welding of metallic materials - General guidance for arc welding) |
BS EN 1011-2-2001 | 焊接.金属材料焊接的推荐规范.铁素体钢的电弧焊接 | (Welding - Recommendations for welding of metallic materials - Arc welding of ferritic steels) |
BS EN 1011-3-2000 | 焊接.金属材料焊接的推荐规范.不锈钢的电弧焊接 | (Welding - Recommendations for welding of metallic materials - Arc welding of stainless steels) |
BS EN 1011-4-2000 | 焊接.金属材料焊接的推荐规范.铝及铝合金的电弧焊接 | (Welding - Recommendations for welding of metallic materials - Arc welding of aluminium and aluminium alloys) |
BS EN 1011-5-2003 | 焊接.金属材料焊接的推荐规范.覆层钢的焊接 | (Welding - Recommendations for welding of metallic materials - Welding of clad steel) |
BS EN 1011-7-2004 | 焊接.金属材料焊接的推荐规范.电子束焊 | |
BS EN 1011-7-2004 | 焊接.金属材料焊接的推荐规范.电子束焊 | |
BS EN 1011-8-2004 | 焊接.金属材料焊接的推荐规范.铸铁的焊接 | |
BS EN 1011-8-2004 | 焊接.金属材料焊接的推荐规范.铸铁的焊接 | |
BS EN 10111-1998 | 冷成型用连续热轧低碳钢薄板及带材.交货技术条件 | (Continuously hot-rolled low carbon steel sheet and strip for cold forming - Technical delivery conditions) |
BS EN 10113-1-1993 | 可焊接细品粒结构钢的热轧制品.一般交货条件 | (Hot-rolled products in weldable fine grain structural steels - General delivery conditions) |
BS EN 10113-2-1993 | 可焊接细粒结构钢的热轧制品.正火/正火轧制钢的交货条件 | (Hot-rolled products in weldable fine grain structural steels - Delivery conditions for normalized/normalized rolled steels) |
BS EN 10113-3-1993 | 可焊接细品粒结构钢的热轧制品.热轧钢的交货条件 | (Hot-rolled products in weldable fine grain structural steels - Delivery conditions for thermomechanical rolled steels) |
BS EN 1012-1-1997 | 压缩机和真空泵.安全要求.压缩机 | (Compressors and vacuum pumps - Safety requirements - Compressors) |
BS EN 1012-2-1997 | 压缩机和真空泵.安全要求.真空泵 | (Compressors and vacuum pumps - Safety requirements - Vacuum pumps) |
BS EN 10120-1997 | 焊接储气瓶用钢薄板及带材 | (Steel sheet and strip for welded gas cylinders) |
BS EN 10126-1996 | 非最终退火装态下非合金钢制冷轧电工钢片和钢带 | (Cold rolled electrical non-alloyed steel sheet and strip delivered in the semi-processed state) |
BS EN 1013-1-1998 | 单层顶板光透明截面塑料板.一般要求和试验方法 | (Light transmitting profiled plastic sheeting for single skin roofing - General requirements and test methods) |
BS EN 1013-2-1999 | 单层顶板光用透光仿型塑料薄板.玻璃纤维增强的聚酯树脂薄板的试验方法和特殊要求 | (Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements and test methods for sheets of glass fibre reinforced polyester resin (GRP)) |
BS EN 1013-3-1998 | 单层顶板光透明截面塑料层.聚氯乙烯板的特殊要求和试验方法 | (Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements and test methods for sheets of polyvinyl chloride (PVC)) |
BS EN 1013-4-2000 | 单层屋顶用透光成型塑料薄板.聚碳酸酯板的特殊要求、试验方法和性能 | (Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements, test methods and performance of polycarbonate (PC) sheets) |
BS EN 1013-5-2000 | 单层屋顶用透光成型塑料薄板.聚甲基丙烯酸甲酯板的特殊要求、试验方法和性能 | (Light transmitting profiled plastic sheeting for single skin roofing - Specific requirements, test methods and performance of polymethylmethacrylate (PMMA) sheets) |
BS EN 10130-1999 | 冷成型的冷轧低碳钢平板制品.技术提交条件 | (Cold-rolled low-carbon steel flat products for cold forming - Technical delivery conditions) |
BS EN 10131-1992 | 冷成型用冷轧未涂覆低碳和高屈服强度钢扁材产品.尺寸和形状公差 | (Cold-rolled uncoated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape) |
BS EN 10132-1-2000 | 热处理用冷轧窄钢条.技术提交条件.总则 | (Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - General) |
BS EN 10132-2-2000 | 热处理用冷轧窄钢条.技术交货条件.表面硬化钢 | (Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Case hardening steels) |
BS EN 10132-3-2000 | 热处理用冷轧窄钢条.技术交货条件.淬火和回火钢 | (Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Steels for quenching and tempering) |
BS EN 10132-4-2000 | 热处理用冷轧窄钢条.技术交货条件.弹簧钢和其它应用 | (Cold rolled narrow steel strip for heat treatment - Technical delivery conditions - Spring steels and other applications) |
BS EN 10136-1991 | 黑色金属材料的化学分析.钢铁中的镍含量的测定.火焰原子吸收光谱测定法 | (Chemical analysis of ferrous materials - Determination of nickel in steels and irons - Flame atomic absorption spectrometric method) |
BS EN 10137-1-1996 | 调质或沉淀硬化状态下高屈服点结构钢制薄板和宽扁钢.第1部分:一般交货条件 | (Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - General delivery conditions) |
BS EN 10137-2-1996 | 调质或剪断硬化状态下高屈服点结构钢制薄板和宽扁钢.第2部分:调质钢的交换条件 | (Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - Delivery conditions for quenched and tempered steels) |
BS EN 10137-3-1996 | 调质或剪断硬化状态下高屈服点结构钢制薄板和宽扁钢.第3部分:剪断硬化钢的交货条件 | (Plates and wide flats made of high yield strength structural steels in the quenched and tempered or precipitation hardened conditions - Delivery conditions for precipitation hardened steels) |
BS EN 10139-1998 | 冷成型用冷轧未涂覆软钢窄带材.交货技术条件 | (Cold rolled uncoated mild steel narrow strip for cold forming - Technical delivery conditions) |
BS EN 1014-1-1995 | 木材防腐.杂酚油和涂油的木材.抽样方法和分析.杂酚油采样过程 | (Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Procedure for sampling creosote) |
BS EN 1014-2-1996 | 木材防腐.杂酚油和涂油的木材.抽样方法和分析.杂酚油采样过程 | (Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Procedure for obtaining a sample of creosote from creosoted timber for subsequent analysis) |
BS EN 1014-3-1998 | 木材防腐.杂酚油和涂油的木材.抽样和分析方法.杂酚油中苯并芘含量的测定 | (Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Determination of the benzo[a]pyrene content of creosote) |
BS EN 1014-4-1996 | 木材防腐剂.煤焦浸渍油及用该油浸渍的木材.取样和分析.第4部分:煤焦浸渍油中水解萃取苯酚含量的测定 | (Wood preservatives - Creosote and creosoted timber - Methods of sampling and analysis - Determination of the water extractable phenols content of creosote) |
BS EN 10140-1997 | 冷轧制窄钢带.尺寸和形状公差 | (Cold rolled narrow steel strip - Tolerances on dimensions and shape) |
BS EN 10142-2000 | 冷成型用连续热浸镀锌低碳钢板材和带材.交货技术条件 | (Continuously hot-dip zinc coated low carbon steels strip and sheet for cold forming - Technical delivery conditions) |
BS EN 10143-1993 | 连续热浸镀金属钢板和钢带的尺寸和形状公差 | (Continuously hot-dip metal coated steel sheet and strip - Tolerances on dimensions and shape) |
BS EN 10147-2000 | 连续热浸镀锌结构薄钢板和带材.交货技术条件 | (Continuously hot-dip zinc coated structural steels strip and sheet - Technical delivery conditions) |
BS EN 10149-1-1996 | 冷成型用高屈服点钢制热轧扁平产品.第1部分:一般交货条件 | (Specification for hot-rolled flat products made of high yield strength steels for cold forming - General delivery conditions) |
BS EN 10149-2-1996 | 冷成型用高屈服点钢制热轧扁平产品.第2部分:热机械轧制钢的交货条件 | (Specification for hot-rolled flat products made of high yield strength steels for cold forming - Delivery conditions for thermomechanically rolled steels) |
BS EN 10149-3-1996 | 冷成型用高屈服点钢制热轧扁平产品.第3部分:普通退火和轧制钢交货条件 | (Specification for hot-rolled flat products made of high yield strength steels for cold forming - Delivery conditions for normalized or normalized rolled steels) |
BS EN 1015-1-1999 | 砖石灰浆试验方法.颗粒尺寸分布的测定(筛分析法) | (Methods of test for mortar for masonry - Determination of particle size distribution (by sieve analysis)) |
BS EN 1015-10-1999 | 砌砖体用灰浆的试验方法.硬化灰浆的毛体积干密度的测定 | Methods of test for mortar for masonry - Determination of dry bulk density of hardened mortar |
BS EN 1015-11-1999 | 砖石灰浆试验方法.硬化灰浆弯曲和抗压强度的测定 | (Methods of test for mortar for masonry - Determination of flexural and compressive strength of hardened mortar) |
BS EN 1015-12-2000 | 圬工辅助件的试验方法.衬底上的硬化灰浆的粘结强度的测定 | (Methods of test for mortar for masonry - Determination of adhesive strength of hardened rendering and plastering mortars on substrates) |
BS EN 1015-17-2000 | 砖石灰浆试验方法.新鲜灰浆中水溶氯化物含量的测定 | (Methods of test for mortar for masonry - Determination of water-soluble chloride content of fresh mortars) |
BS EN 1015-18-2002 | 砖石灰浆试验方法.通过硬化沙浆的毛细管作用测定吸水率 | (Methods of test for mortar for masonry - Determination of water absorption coefficient due to capillary action of hardened mortar) |
BS EN 1015-19-1999 | 砖石灰浆试验方法.硬化粉刷灰浆和灰泥灰浆水蒸发渗透性的测定 | (Methods of test for mortar for masonry - Determination of water vapour permeability of hardened rendering and plastering mortars) |
BS EN 1015-1999 | 砖石灰浆试验方法.硬化粉刷灰浆和灰泥灰浆水蒸发渗透性的测定 | (Methods of test for mortar for masonry. Determination of water vapour permeability of hardened rendering and plastering mortars) |
BS EN 1015-2-1999 | 砖石灰浆试验方法.试验灰浆制备和灰浆集块取样 | (Methods of test for mortar for masonry - Bulk sampling of mortars and preparation of test mortars) |
BS EN 1015-21-2002 | 砖石灰浆试验方法.带基质的单层初涂沙浆可混合性的测定 | (Methods of test for mortar for masonry - Determination of the compatibility of one-coat rendering mortars with substrates) |
BS EN 1015-3-1999 | 砖石灰浆的试验方法.新鲜灰浆连续性测定 | (Methods of test for mortar for masonry - Determination of consistence of fresh mortar (by flow table)) |
BS EN 1015-4-1999 | 砖石灰浆试验方法.新鲜灰浆连续性的测定(倾倒渗透法) | (Methods of test for mortar for masonry - Determination of consistence of fresh mortar (by plunger penetration)) |
BS EN 1015-6-1999 | 砖石灰浆试验方法.新鲜灰浆集块密度的测定 | (Methods of test for mortar for masonry - Determination of bulk density of fresh mortar) |
BS EN 1015-7-1999 | 砖石灰浆试验方法.新鲜灰浆空气含量的测定 | (Methods of test for mortar for masonry - Determination of air content of fresh mortar) |
BS EN 1015-9-1999 | 砖石灰浆试验方法.新鲜灰浆使用寿命和校正时间的测定 | (Methods of test for mortar for masonry - Determination of workable life and correction time of fresh mortar) |
BS EN 10151-2002 | 弹簧用不锈钢带材.交货技术条件 | (Stainless steel strip for springs - Technical delivery conditions) |