标准号 |
中文名称 |
英文名称 |
DIN ISO 8693-2000 |
模压工具.平起模杆 |
(Tools for moulding - Flat ejector pins (ISO 8693:1998)) |
DIN ISO 8694-2000 |
模压工具.有肩的起模杆 |
(Tools for moulding - Shouldered ejector pins (ISO 8694:1998)) |
DIN ISO 8719-1988 |
商业用车辆和大型客车.齿轮传动空气压缩机用四孔法兰盘 |
(Commercial vehicles and buses; four-hole flanges for gear-driven air compressors; identical with ISO 8719, edition 1986) |
DIN ISO 8756-1996 |
空气质量.温度,压力和湿度的数据处理 |
(Air quality - Handling of temperature, pressure and humidity data (ISO 8756:1994)) |
DIN ISO 8758-1997 |
电影技术.在16mm和35mm电影胶片和拷贝上的影相图形的控制记录和数据记录.尺寸和定位 |
(Cinematography - Photographic control and data records on 16 mm and 35 mm motion-picture film and prints - Dimensions and location (ISO 8758:1992)) |
DIN ISO 8759-1-1999 |
农业机械和拖拉机.前悬装置.第1部分:动力输出轴和三点悬挂装置 |
(Agricultural machinery and tractors - Front-mounted equipment - Part 1: Power take-off and three-point linkage (ISO 8759-1:1998)) |
DIN ISO 8764-1-2000 |
螺钉和螺母用装配工具.十字头螺钉旋具.第1部分:驱动头 |
(Assembly tools for screws and nuts - Screwdrivers for cross-recessed head screws - Part 1: Driver points (ISO 8764-1:1999)) |
DIN ISO 8764-2-2000 |
十字头螺钉旋具.第2部分:一般要求、刀片长度和手操作旋具标志 |
(Screwdrivers for cross-recessed head screws - Part 2: General requirements, lengths of blades and marking of hand-operated screwdrivers (ISO 8764-2:1992)) |
DIN ISO 8767-1995 |
汽车轮胎.滚动阻力测量法 |
(Passenger car tyres - Methods of measuring rolling resistance; identical with ISO 8767:1992) |
DIN ISO 8775-1988 |
航空和航天.液压系统用氧气补充连接管.尺寸(英制) |
(Aerospace; gaseous oxygen replenishment connection for use in fluid systems (new type); dimensions (inch series); identical with ISO 8775:1988) |
DIN ISO 8783-1999 |
高山滑雪.斜坡性能指南 |
(Alpine skis - Guidelines for conducting slope performance tests (ISO 8783:1999)) |
DIN ISO 8787-1994 |
纸和纸板的检验.毛细上升的测定.克莱姆(KIEMM)法 |
(Testing of paper and board; determination of capillary rise; Klemm method; identical with ISO 8787:1986) |
DIN ISO 8788-1988 |
航空和航天.紧固件.螺母的形状和位置公差 |
(Aerospace; fasteners; tolerances of form and position for nuts; identical with ISO 8788, edition 1987) |
DIN ISO 8791-4-1996 |
纸和纸板.粗糙度和平滑度的测定(漏气法).第4部分:激浪印刷法 |
(Paper and board - Determination of roughness/smoothness (air leak methods) - Part 4: Print-surf method (ISO 8791-4:1992)) |
DIN ISO 8805-1991 |
信息处理系统.计算机制图.三维图形核心系统(GKS-3D).功能描述 |
(Information processing systems; computer graphics; graphical kernel system for three dimensions (GKS-3D) functional description; identical with ISO 8805:1988) |
DIN ISO 8821-1991 |
机械振动.平衡.用键联结的轴和配件 |
(Mechanical vibration; balancing shaft and fitment key convention; identical with ISO 8821:1989) |
DIN ISO 8826-1-1990 |
技术制图.滚动轴承.第1部分:通用简化画法 |
(Technical drawings; rolling bearings; part 1: general simplified representation; identical with ISO 8826-1:1989) |
DIN ISO 8826-2-1995 |
技术制图.滚动轴承.第2部分:详细简化画法 |
(Technical drawings - Rolling bearings - Part 2: Detailed simplified representation (ISO 8826-2:1994)) |
DIN ISO 8847-1990 |
小型船舶.转向装置.钢索和滑轮系统 |
(Small craft; steering gear; wire rope and pulley systems (ISO 8847: 1987); german version EN 28847:1989) |
DIN ISO 885-2001 |
一般用途螺栓和螺钉.米制系列.端头半径 |
(General purpose bolts and screws - Metric series - Radii under the head (ISO 885:2000)) |
DIN ISO 8854-1989 |
道路车辆.带调节器的交流发电机.试验方法和一般要求 |
(Road vehicles; alternators with regulators; test methods and general requirements; identical with ISO 8854:1988) |
DIN ISO 8856-1997 |
道路车辆.起动电动机的电器性能.试验方法和一般要求 |
(Road vehicles - Electrical performance of starter motors - Test methods and general requirements (ISO 8856:1995)) |
DIN ISO 8862-1990 |
船舶机械控制室的空气调节和通风.设计条件和计算基础 |
(Air-conditioning and ventilation of machinery control-rooms on board ships; design conditions and basis of calculations; identical with ISO 8862:1987) |
DIN ISO 8863-1990 |
船舶驾驶室窗户.窗格玻璃热风加热 |
(Ship`s wheelhouse windows; heating by hot air of glass panes; identical with ISO 8863:1987) |
DIN ISO 8864-1990 |
船舶驾驶室的空气调节和通风.设计条件和计算基础 |
(Air-conditioning and ventilation of wheelhouse on board ships; design conditions and basis of calculations; identical with ISO 8864:1987) |
DIN ISO 8871-1990 |
含水非肠道药配制器用弹性件 |
(Elastometric parts for aqueous parenteral preparations; identical with ISO 8871:1990) |
DIN ISO 8871/A1-1996 |
含水非肠胃道药剂配制用弹性体部件.修改件1 |
(Elastomeric parts for aqueous parenteral preparations; Amendment A1 (ISO 8871:1990 AMD 1:1995)) |
DIN ISO 8872-1989 |
输血、输液及注射瓶的铝盖.一般要求和试验方法 |
(Aluminium caps for transfusion, infusion and injection bottles; general requirements and test methods; identical with ISO 8872:1988) |
DIN ISO 8909-1-2000 |
农机和拖车.饲料作物收割机.第1部分:词汇 |
(Agricultural machinery and tractors - Forage harvesters - Part 1: Vocabulary (ISO 8909-1:1994)) |
DIN ISO 8909-2-2000 |
农机和拖车.饲料作物收割机.第2部分:特性和性能规范 |
(Agricultural machinery and tractors - Forage harvesters - Part 2: Specification of characteristics and performance (ISO 8909-2:1994)) |
DIN ISO 8909-3-2000 |
农机和拖车.饲料作物收割机.第3部分:试验方法 |
(Agricultural machinery and tractors - Forage harvesters - Part 3: Test methods (ISO 8903-3:1994)) |
DIN ISO 8930-1991 |
结构可靠性的一般原则.等义术语表 |
(General principles on reliability for structures; list of equivalent terms; identical with ISO 8930:1987) |
DIN ISO 8935-1991 |
农业机械和拖拉机.外部设备控制器的安装座和开口 |
(Agricultural machinery and tractors; mounting, aperture for external equipment controls; identical with ISO 8935:1990) |
DIN ISO 8936-1992 |
大篷车的遮篷.安全要求 |
(Caravan awnings; safety requirements; identical with ISO 8936:1988) |
DIN ISO 8936-2003 |
大篷车的遮篷.安全要求 |
(Caravan awnings - Safety requirements (ISO 8936:2003)) |
DIN ISO 8937-2001 |
旅居车篷.功能要求和试验方法 |
(Caravan-awnings - Functional requirements and test methods (ISO 8937:2000)) |
DIN ISO 897-1993 |
摄影技术.胶卷.126、110和135胶卷.载像面的鉴别 |
(Photography; roll films; 126, 110 and 135 size films; identification of the image-bearing side; identical with ISO 897:1988) |
DIN ISO 897-2005 |
摄影.126、110和135规格胶卷.成相面的识别 |
|
DIN ISO 8975-1992 |
塑料.酚醛树脂.pH值的测定 |
(Plastics; phenolic resins; determination of pH; identical with ISO 8975:1989) |
DIN ISO 8976-1994 |
夹扭钳和剪切钳.多滑动结合手钳.尺寸和试验值 |
(Pliers and nippers - Multiple slip joint pliers - Dimensions and test values; identical with ISO 8976:1988) |
DIN ISO 8977-2003 |
冲压工具.冲模 |
(Tools for pressing - Matrixes (ISO 8977:2003)) |
DIN ISO 8979-1995 |
电子设备用的夹扭钳和剪切钳和夹钳.术语 |
(Pliers and nippers for electronics - Nomenclature; identical with ISO 8979:1988) |
DIN ISO 8984-1-1994 |
柴油发动机.喷嘴架组件的检验.第1部分:手操作检验仪和调整仪 |
(Diesel engines - Testing of fuel injectors - Part 1: Hand-lever-operated testing and setting apparatus; identical with ISO 8984-1:1993) |
DIN ISO 8984-2-1994 |
柴油发动机.喷嘴架组件的检验.第2部分:检验方法 |
(Diesel engines - Testing of fuel injectors - Part 2: Test methods; identical with ISO 8984-2:1993) |
DIN ISO 8992-1992 |
紧固件.螺钉和螺母的一般要求 |
(Fasteners; general requirements for bolts, screws, studs and nuts; identical with ISO 8992:1986) |
DIN ISO 8992-2005 |
紧固件.螺栓、螺钉、螺柱和螺母的一般要求 |
|
DIN ISO 9000-4-1994 |
质量管理和质量保证标准.可靠性程序管理指南 |
(Quality management and quality assurance standards; guide to dependability programme management (identical with ISO 9000-4:1993 resp. IEC 60300-1:1993); German version EN 60300-1:1993) |
DIN ISO 9004-2-1992 |
质量管理和质量保证体系的素.服务业导则 |
(Quality management and quality system elements; part 2: guidelines for services; identical with ISO 9004-2:1991) |
DIN ISO 9010-1990 |
同步皮带传动装置.汽车用皮带 |
(Synchronous belt drives; automotive belts; identical with ISO 9010:1987) |
DIN ISO 9011-1990 |
同步皮带传动装置.汽车皮带轮 |
(Synchronous belt drives; automotive pulleys; identical with ISO 9011:1987) |
DIN ISO 9022-1-1999 |
光学和光学仪器.环境试验方法.第1部分:定义.试验的范围 |
(Optics and optical instruments - Environmental test methods - Part 1: Definitions, extent of testing (ISO 9022-1:1994)) |
DIN ISO 9022-10-2000 |
光学和光学仪器.环境试验方法.第10部分:正弦振动和干热法或低温法的组合 |
(Optics and optical instruments - Environmental test methods - Part 10: Combined sinusoidal vibration and dry heat or cold (ISO 9022-10:1998)) |
DIN ISO 9022-11-2000 |
光学和光学仪器.环境试验方法.第11部分:霉菌生长 |
(Optics and optical instruments - Environmental test methods - Part 11: Mould growth (ISO 9022-11:1994)) |
DIN ISO 9022-12-2000 |
光学和光学仪器.环境试验方法.第12部分:污染 |
(Optics and optical instruments - Environmental test methods - Part 12: Contamination (ISO 9022-12:1994)) |
DIN ISO 9022-13-2001 |
光学和光学仪器.环境试验方法.第13部分:组合冲击、碰撞或自由降落与干热或干冷的试验 |
(Optics and optical instruments - Environmental test methods - Part 13: Combined shock, bump or free fall and dry heat or cold (ISO 9022-13:1998)) |
DIN ISO 9022-14-2001 |
光学和光学仪器.环境试验方法.第14部分:露水、霜及冰 |
Optics and optical instruments - Environmental test methods - Part 14: Dew, hoarfrost, ice (ISO 9022-14:1994) |
DIN ISO 9022-15-2001 |
光学和光学仪器.环境试验方法.第15部分:组合的数字控制宽带随机振动和干热及干冷的试验 |
Optics and optical instruments - Environmental test methods - Part 15: Combined digitally controlled broad-band random vibration and dry heat or cold (ISO 9022-15:1998) |
DIN ISO 9022-16-2001 |
光学和光学仪器.环境试验方法.第16部分:组合跳动或稳定状态的加速度与干热或干冷的试验 |
Optics and optical instruments - Environmental test methods - Part 16: Combined bounce or steady-state acceleration and dry heat or cold (ISO 9022-16:1998) |
DIN ISO 9022-17-2001 |
光学和光学仪器.环境试验方法.第17部分:组合污染与太阳辐射的试验 |
Optics and optical instruments - Environmental test methods - Part 17: Combined contamination, solar radiation (ISO 9022-17:1994) |
DIN ISO 9022-18-2001 |
光学和光学仪器.环境试验方法.第18部分:组合湿热及低内压力的试验 |
Optics and optical instruments - Environmental test methods - Part 18: Combined damp heat and low internal pressure (ISO 9022-18:1994) |
DIN ISO 9022-19-2001 |
光学和光学仪器.环境试验方法.第19部分:与正弦或随机振动相结合的温度循环的试验 |
Optics and optical instruments - Environmental test methods - Part 19: Temperature cycles combined with sinusoidal or random vibration (ISO 9022-19:1994) |
DIN ISO 9022-2-2003 |
光学和光学仪器.环境试验方法.第2部分:冷、热和湿度 |
Optics and optical instruments - Environmental test methods - Part 2: Cold, heat and humidity (ISO 9022-2:2002) |
DIN ISO 9022-20-2001 |
光学和光学仪器.环境试验方法.第20部分:含有硫化氢或二氧化硫的湿空气的试验 |
Optics and optical instruments - Environmental test methods - Part 20: Humid atmosphere containing sulfur dioxide or hydrogen sulfide (ISO 9022-20:1997) |
DIN ISO 9022-21-2001 |
光学和光学仪器.环境试验方法.第21部分:组合低压和室温或干热的试验 |
Optics and optical instruments - Environmental test methods - Part 21: Combined low pressure and ambient temperature or dry heat (ISO 9022-21:1998) |
DIN ISO 9022-3-2000 |
光学和光学仪器.环境试验方法.第3部分:机械应力 |
Optics and optical instruments - Environmental test methods - Part 3: Mechanical stress (ISO 9022-3:1998) |
DIN ISO 9022-4-2003 |
光学和光学仪器.环境试验方法.第4部分:盐雾 |
Optics and optical instruments - Environmental test methods - Part 4: Salt mist (ISO 9022-4:2002) |
DIN ISO 9022-5-1999 |
光学和光学仪器.环境试验方法.第5部分:低温,低压 |
Optics and optical instruments - Environmental test methods - Part 5: Combined cold, low air pressure (ISO 9022-5:1994) |
DIN ISO 9022-6-1999 |
光学和光学仪器.环境试验方法.第6部分:尘埃 |
Optics and optical instruments - Environmental test methods - Part 6: Dust (ISO 9022-6:1994) |
DIN ISO 9022-7-1999 |
光学和光学仪器.环境试验方法.第7部分:滴水,雨 |
Optics and optical instruments - Environmental test methods - Part 7: Drip, rain (ISO 9022-7:1994) |
DIN ISO 9022-8-2000 |
光学和光学仪器.环境试验方法.第8部分:高压、低压及浸渍 |
Optics and optical instruments - Environmental test methods - Part 8: High pressure, low pressure, immersion (ISO 9022-8:1994) |
DIN ISO 9022-9-2000 |
光学和光学仪器.环境试验方法.第9部分:太阳辐射 |
Optics and optical instruments - Environmental test methods - Part 9: Solar radiation (ISO 9022-9:1994) |
DIN ISO 9044-2001 |
工业用纺织金属丝布.技术要求和试验 |
Industrial woven wire cloth - Technical requirements and testing (ISO 9044:1999) |
DIN ISO 9045-1998 |
工业用网筛和筛分.词汇 |
Industrial screens and screening - Vocabulary (ISO 9045:1990) |
DIN ISO 9069-1991 |
信息处理.SGML支持设备.SGML文献交换格式(SDIF) |
Information processing; SGML support facilities; SGML document interchange format (SDIF); identical with ISO 9069:1988 |
DIN ISO 9090-1990 |
气焊以及类似的处理过程中设备的气密特性 |
Gas tightness of equipment for gas welding and allied processes; identical with ISO 9090:1989 |
DIN ISO 9099-1990 |
船舶干燥的储备室的空气调节和通风.设计条件和计算基础 |
Air-conditioning and ventilation of dry provision rooms on board ships; design conditions and basis of calculations; identical with ISO 9099:1987 |
DIN ISO 91-1-1984 |
石油测定表.第1部分:根据参比温度15℃和60°F编制的表 |
(Petroleum measurement tables; part 1: tables based on reference temperatures of 15 C and 60 F) |
DIN ISO 9102-1992 |
道路车辆.压燃式发动机.24.25.26型拧入式喷嘴座 |
(Road vehicles; compression-ignition engines; screw-in injection nozzle holders, types 24, 25 and 26; Identical with ISO 9102:1990) |
DIN ISO 9119-1991 |
越野滑雪板.连接固定区.要求和试验方法 |
(Cross-country skis; binding mounting area; requirements and test methods; identical with ISO 9119:1990) |
DIN ISO 9120-2005 |
石油及相关产品.汽轮机油和其他油的空气释放性能的测定.冲击滤尘器法 |
|
DIN ISO 9136-1996 |
粗晶粒磨料.容积密度的测定 |
(Abrasive macrograins - Determination of bulk density (ISO 9136:1989)) |
DIN ISO 9136-2-2000 |
粗晶粒磨料.容积密度的测定.微小磨料 |
(Abrasive grains - Determination of bulk density - Part 2: Microgrits (ISO 9136-2:1999)) |
DIN ISO 9137-1996 |
磨料粒度.毛细(管)作用测定 |
(Abrasive macrograins - Determination of capillarity (ISO 9137:1990)) |
DIN ISO 9138-1996 |
磨料粒度.取样和分割 |
(Abrasive grains - Sampling and splitting (ISO 9138:1993)) |
DIN ISO 9141-1992 |
道路车辆.诊断系统.对数字信息交换的要求 |
(Road vehicle; diagnostic systems; requirements for interchange of digital information; identical with ISO 9141:1989) |
DIN ISO 9152-2005 |
航空航天.强度等级为1100 MPa的钛合金制MJ螺纹螺栓.采购规范 |
|
DIN ISO 9158-1989 |
道路车辆.无铅汽油用管嘴 |
(Road vehicles; nozzle spouts for unleaded gasoline; identical with ISO 9158:1988) |
DIN ISO 9159-1989 |
道路车辆.含铅汽油和柴油用管嘴 |
(Road vehicles; nozzle spouts for leaded gasoline and diesel fuel; identical with ISO 9159:1988) |
DIN ISO 9169-1996 |
空气质量.操作特性的测量方法 |
(Air quality - Determination of performance characteristics of measurement methods (ISO 9169:1994)) |
DIN ISO 9175-1-1990 |
用绘图墨水的手持式描图纸专用笔的管状笔尖.第1部分:概念.尺寸.名称与符号及标志 |
(Tubular tips for hand-held technical pen using india ink; definitions, dimensions, designation and marking; identical with ISO 9175-1:1988) |
DIN ISO 9175-2-1990 |
用印度墨水的手持式描图纸专用笔的管状笔尖.第2部分:结构.要求和检验 |
(Tubular tips for hand-held technical pen using india ink; performance, test parameters and test conditions; identical with ISO 9175-2:1988) |
DIN ISO 9176-1993 |
管状制图笔.圆规转接器 |
(Tubular technical pens; adaptor for compasses; identical with ISO 9176:1988) |
DIN ISO 9177-1-1990 |
制图自动铅笔.第1部分:分类.尺寸和性能的要求和检验 |
(Mechanical pencils; classification, dimensions, performance requirements and testing; identical with ISO 9177-1:1989) |
DIN ISO 9177-2-1990 |
制图自动铅笔.第2部分:石墨.分类和尺寸 |
(Mechanical pencils; black leads, classification and dimensions; identical with ISO 9177-2:1989) |
DIN ISO 9177-3-1995 |
制图自动铅笔.第3部分:石墨.HB笔芯的抗弯强度 |
(Mechanical pencils - Part 3: Black leads; bending strengths of HB leads; identical with ISO 9177-3:1994) |
DIN ISO 9178-1-1992 |
书写和符号的模板.第1部分:一般原则和鉴别标记 |
(Templates for lettering and symbols; general principles and identification markings; identical with ISO 9178-1:1988) |
DIN ISO 9178-2-1992 |
书写和符号的模板.第2部分:木皮铅笔和细铅笔的槽宽 |
Templates for lettering and symbols; slot widths for wood-cased pencils, clutch pencils and fine-lead pencils; identical with ISO 9178-2:1988 |
DIN ISO 9178-3-1992 |
文字和符号的模板.第3部分:按照ISO 9157-1管形笔尖的技术钢笔用的槽宽 |
Templates for lettering symbols; slot widths for technical pens with tubular tips in accordance with ISO 9175-1; identical with ISO 9178-3:1989 |
DIN ISO 9180-1989 |
木壳铅笔的黑色铅芯.分类及直径 |
Black leads for wood-cased pencils; classification and diameters; identical with ISO 9180:1988 |
DIN ISO 9183-1-1992 |
冲压工具.第1部分:冲压工具用抗磨板.型号A |
Tools for pressing; wear plates for press dies; typ A; identical with ISO 9183-1:1990 |
DIN ISO 9187-1-2000 |
医用注射设备.第1部分:注射针用安瓿瓶 |
Injection equipment for medical use - Part 1: Ampoules for injectables (ISO 9187-1:2000) |
DIN ISO 9187-2-1994 |
医用注射器.单点切割安瓿 |
Injection equipment for medical use; one point cut ampoules (OPC); identical with ISO 9187-2:1993 |
DIN ISO 9193-1992 |
园林和农业管理.草地和园林使用的拖拉机.动力输轴 |
Garden and landscope maintenance; lawn and garden tractors; power take-off; identical with ISO 9193:1990 |
DIN ISO 92-1980 |
纺织机械和辅助装置.纺纱机.左右侧的定义 |
(Textile machinery and accessories; spinning machinery, definition of side (left or right)) |
DIN ISO 9203-1-1991 |
造船数据处理.船体结构零件的布局.第1部分:零件定位 |
(Shipbuilding; information processing; topology of ship hull structure elements; location of elements; identical with ISO 9203-1:1989) |
DIN ISO 9203-2-1991 |
造船.船体结构零件的布局.第2部分:零件的描述 |
(Shipbuilding; information processing; topology of ship hull structure elements; description of elements; identical with ISO 9203-2:1989) |
DIN ISO 9203-3-1991 |
造船数据处理.船体结构零件的布局.第3部分:零件间的关系 |
(Shipbuilding; information processing; topology of ship hull structure elements; relations of elements; identical with ISO 9203-3:1989) |
DIN ISO 9211-1-2001 |
光学和光学仪器.光覆层.第1部分:定义(ISO9211-1:1994) |
(Optics and optical instruments - Optical coatings - Part 1: Definitions (ISO 9211-1:1994)) |
DIN ISO 9211-2-2001 |
光学和光学仪器.光学涂层.第2部分:光学特性 |
(Optics and optical instruments - Optical coatings - Part 2: Optical properties (ISO 9211-2:1994)) |
DIN ISO 9211-3-2001 |
光学和光学仪器.光学涂层.第3部分:环境稳定性 |
(Optics and optical instruments - Optical coatings - Part 3: Environmental durability (ISO 9211-3:1994)) |
DIN ISO 9222-1-1990 |
技术制图.动负荷用密封.总体.简化画法 |
(Technical drawings; seals for dynamic application; part 1: general simplified representation; identical with ISO 9222-1:1989) |
DIN ISO 9222-2-1991 |
技术制图.动负荷用密封.细节.简化画法 |
(Technical drawings; seals for dynamic application; part 2: detailed simplified representation; identical with ISO 9222-2:1989) |
DIN ISO 9242-1994 |
夹扭钳和剪切钳.建筑工人的夹钳.尺寸和试验值 |
(Pliers and nippers - Construction worker`s pincers - Dimensions and test values; identical with ISO 9242:1988) |
DIN ISO 9243-1994 |
夹扭钳和剪切钳.细木工的夹钳.尺寸和试验值 |
(Pliers and nippers - Carpenter`s pincers - Dimensions and test values; identical with ISO 9243:1988) |
DIN ISO 9245 Bb.1-1995 |
土方机械.机器生产率.词汇、符号和单位.说明注释 |
(Earth-moving machinery - Machine productivity - Vocabulary, symbols and units; explanatory notes) |
DIN ISO 9245-1995 |
土方机械.机器生产率.词汇、符号和单位 |
(Earth-moving machinery - Machine productivity - Vocabulary, symbols and units; identical with ISO 9245:1991) |
DIN ISO 9252-1998 |
合成胶乳.微生物的检验 |
(Synthetic rubber latex - Microbiological examination (ISO 9252:1989)) |
DIN ISO 9271-1995 |
放射污染表面的清除.织物用污染去除剂试验 |
(Decontamination of radioactively contaminated surfaces - Testing of decontamination agents for textiles; identical with ISO 9271:1992) |
DIN ISO 9276-1-2004 |
粒度分析结果的表示.第1部分:图形表示 |
|
DIN ISO 9277-2003 |
用BET法通过气体吸收测定固体的比表面积 |
(Determination of the specific surface area of solids by gas adsorption using the BET method (ISO 9277:1995)) |