标准号 |
中文名称 |
英文名称 |
| NF E26-111-1985 |
链传动.落锤锻件非铆接链 |
(CHAIN TRANSMISSION. DROP FORGED RIVETLESS CHAINS FOR CONVEYORS.) |
| NF E26-112-1996 |
滚动链驱动的选择指南 |
(Guidance on the selection of roller chain drives.) |
| NF E26-114-1993 |
环链.特性和试验方法 |
(Cycles chains. Characteristics and test methods.) |
| NF E26-115-1993 |
摩托车圆链.特性和试验方法 |
(MOTOR CYCLE CHAINS. CHARACTERISTICS AND TEST METHODS.) |
| NF E27-000-1972 |
螺栓、螺母及附件.术语 |
(Bolts, nuts and accessories.nomenclature.) |
| NF E27-009-1979 |
紧固件.轴向负荷疲劳试验 |
(FASTENERS. FATIGUE TEST UNDER AXIAL LOAD.) |
| NF E27-151-1952 |
柱圆头铆钉 |
(CHEESE HEAD RIVETS.) |
| NF E27-152-1952 |
半沉头铆钉 |
(RAISED MUSHROOM HEAD RIVETS.) |
| NF E27-153-1952 |
圆头铆钉 |
(ROUND HEAD RIVETS.) |
| NF E27-154-1952 |
沉头铆钉 |
(RIVETS WITH COUNTERSUNK HEAD.) |
| NF E27-155-1952 |
机械结构、金属结构和锅炉用铆钉公差 |
(RIVET TOLERANCES FOR MECHANICAL,METAL AND BOILER CONSTRUCTION.) |
| NF E27-156-1983 |
紧固件.结构安装用圆头铆钉 |
(Fasteners. Structural round head rivets.) |
| NF E27-163-1972 |
调整螺钉 |
(ADJUSTING SCREW.) |
| NF E27-164-1976 |
锁紧螺钉的垫板 |
(LOCKING SCREW.) |
| NF E27-165-1976 |
锁紧螺钉的穿销 |
(SLIDE FOR LOCKING SCREW.) |
| NF E27-166-1976 |
滚花头锁紧螺钉 |
(LOCKING SCREW WITH KNURLED KNOB.) |
| NF E27-167-1976 |
星形手扭锁紧螺钉 |
(LOCKING SCREW WITH PALM KNOB.) |
| NF E27-168-1976 |
四翼锁紧螺钉 |
(LOCKING SCREW WITH 4 ARMED KNOB.) |
| NF E27-169-1972 |
带螺纹的转向销 |
(SCREWED SWIVEL PIN.) |
| NF E27-170-1974 |
通用滚花头螺钉 |
(GENERAL PURPOSE KNURLED THUMBS SCREWS.) |
| NF E27-191-1983 |
紧固件.有肩固定螺钉 |
(FASTENERS. SHOULDERED RETAINING SCREWS.) |
| NF E27-209-1976 |
小提琴上调音用蝶形螺母 |
(THUMB NUT “VIOLON TYPE“.) |
| NF E27-214-1976 |
带小提琴紧弦用的蝶形螺母锁紧螺钉 |
(LOCKING SCREW WITH VIOLIN TYPE THUMB NUT.) |
| NF E27-215-1976 |
带六角螺母的锁紧螺钉 |
(LOCKING SCREWS WITH HEXAGON NUT.) |
| NF E27-303-1968 |
有孔球头螺钉 |
(SPHERICAL HOLED HEAD SCREW.) |
| NF E27-312-1959 |
商业性通用螺栓制造.圆柱头粗制或精制螺栓 |
(CHEESE HEAD NIB BOLTS.) |
| NF E27-313-1959 |
商业性通用螺栓制造.圆头粗制或精制螺栓.直径从４到６０mm |
(ROUND HEAD NIB BOLTS.) |
| NF E27-314-1959 |
商业性通用螺栓制造.埋头或凸圆埋头铁制粗制或精制螺栓.直径４到６０mm |
(COUNTERSUNK OR RAISED COUNTERSUNK HEAD NIB BOLTS.) |
| NF E27-341-1973 |
商业性通用螺栓制造.“木结构”螺栓 |
(BOLTS FOR TIMBER.) |
| NF E27-342-1961 |
商业性通用螺栓制造.埋头或凸圆埋头木螺栓 |
(COUNTERSUNK OR RAISED COUNTERSUNK HEAD BOLTS (NIB OR SQUARE NECK) FOR TIMBER.) |
| NF E27-351-1969 |
商业性通用螺栓制造.凸圆头方颈螺栓 |
(ROUND HEAD SQUARE NECK BOLTS (“JAPY“ TYPE).) |
| NF E27-353-1961 |
商业性通用螺栓制造.带销埋头犁形螺栓 |
(COUNTERSUNK HEAD NIB BOLTS (“PLOUGHSHARE“ TYPE).) |
| NF E27-354-1961 |
商业性通用螺栓制造.方颈埋头犁形螺栓 |
(COUNTERSUNK HEAD SQUARE NECK BOLTS (“PLOUGHSHARE“ TYPE).) |
| NF E27-355-1980 |
紧固件.底板受力器材.轻微磨损零件固定用的双耳埋头螺栓 |
(FASTENERS. EQUIPMENT FOR WORKING THE SOIL. COUNTERSUNK HEAD NIB BOLTS FOR FASTENING THIN WEAR PARTS.) |
| NF E27-381-1969 |
销钉轴和螺纹轴 |
(CLEVIS PINS AND SCREWED SPINDLES.) |
| NF E27-412-1973 |
商业性通用螺栓制造.宽的方螺帽.直径４到３０mm |
(LARGE SQUARE NUTS.DIAMETERS FROM 4 TO 30 MM.) |
| NF E27-413-1959 |
圆柱螺帽（旧称圆螺帽） |
(SLOTTED CYLINDRICAL NUTS.) |
| NF E27-414-1969 |
螺栓制造.冠形螺帽 |
(CASTLE NUTS.) |
| NF E27-432-1984 |
凸肩对接公制螺纹金属螺塞.六角头与平垫片 |
(Metric screw hexagon head metal plugs with collar joints for use with gaskets.) |
| NF E27-433-1984 |
凸肩对接公制螺纹金属螺塞.六角头与Ｏ形密封垫圈 |
(METRIC SCREW HEXAGON HEAD METAL PLUGS WITH COLLAR JOINTS FOR USE WITH O. RINGS.) |
| NF E27-434-1984 |
凸肩对接公制螺纹金属螺塞.内六角圆柱头与平垫片 |
(Metric screw hexagon socket cylindrical head metal plugs with collar joints for use with gaskets.) |
| NF E27-453-1966 |
罩形螺帽.直径３到８mm |
(CAP NUTS.) |
| NF E27-454-1964 |
蝶形螺帽 |
(WING NUTS.) |
| NF E27-455-1976 |
滚花螺帽 |
(KNURLED KNOB.) |
| NF E27-456-1976 |
十字头螺帽 |
(PALM KNOB.) |
| NF E27-457-1976 |
四翼螺帽 |
(4-ARMED KNOB.) |
| NF E27-458-1966 |
球面突出式螺帽.直径４到３６mm |
(NUTS WITH SPHERICAL BEARING SURFACE.) |
| NF E27-459-1974 |
通用滚花螺帽 |
(GENERAL PURPOSE KNURLED NUTS.) |
| NF E27-460-1980 |
自锁弹性螺帽 |
(FASTENERS. SELF LOCKING COUNTER NUTS.) |
| NF E27-477-1972 |
带螺纹孔.莫氏锥定位销 |
(MORSE TAPER PINS WITH EXTERNAL THREAD.) |
| NF E27-478-1972 |
螺纹孔.莫氏锥定位销 |
(MORSE TAPER PINS WITH INTERNAL THREAD.) |
| NF E27-481-1978 |
锥形销 |
(TAPER PINS.) |
| NF E27-488-1972 |
商业性通用螺栓制造.小销 |
(Cotter pin hole dimensions.) |
| NF E27-615-1972 |
球面垫圈 |
(WASHER WITH SPHERICAL SEAT.) |
| NF E27-616-1972 |
可拆卸切口垫圈 |
(DEMOUNTABLE WASHER WITH SLOT.) |
| NF E27-617-1972 |
可转动切口垫圈 |
(PIVOT WASHER WITH SLOT.) |
| NF E27-619-1951 |
托盘式垫圈 |
(DISHED WASHER.) |
| NF E27-620-1981 |
双波的波形弹性垫圈 |
(FASTENERS. GRINKLE SPRING WASHER.) |
| NF E27-624-1981 |
外齿重迭垫圈.平型 |
(SERRATED LOCK WASHERS EXTERNAL TEETH.) |
| NF E27-625-1981 |
内齿重迭垫圈.平型 |
(SERRATED LOCK WASHERS INTERNAL TEETH.) |
| NF E27-626-1982 |
内外齿垫圈.平型 |
(Serrated lock washers. Double row of teeth. Plain form.) |
| NF E27-627-1982 |
重迭外齿垫圈.凹形的 |
(Serrated lock washers. External teeth. Concave form.) |
| NF E27-681-1939 |
Ｕ或Ｔ形断面ＩＰＮ梁的斜楔 |
(CHANNEL IRON CLAMPING PLATES FOR IPN,U OR T SECTIONS.) |
| NF E27-682-1965 |
商业性通用螺栓制造.木结构螺栓装配的垫圈和垫片 |
(Round or square washers for timber.) |
| NF E27-701-1984 |
金属结构施工检验紧固螺栓.技术规范.订货,检验和供货条件 |
(Structural bolts and nuts intented for use in steel structures. Technical specifications. Order, test and delivery conditions.) |
| NF E27-702-1984 |
金属结构施工检验紧固螺栓.螺栓使用性能试验 |
(Structural bolts and nuts intented for use in steel structures. Test on suitability of bolts for use.) |
| NF E27-711-1982 |
金属结构施工检验紧固螺栓.六角头螺栓.尺寸和公差 |
(Locking bolts and nuts intended for use in metal constructions. Hexagon bolts. Dimensions and tolerances.) |
| NF E27-801-1970 |
焊接杆 |
(WELD ROD WITH SCREWED END.) |
| NF E27-811-1970 |
鱼尾形密封销 |
(RAG BOLTS.) |
| NF E27-816-1998 |
锚栓.试验用 |
(Anchor bolts. Fitness for use tests.) |
| NF E27-852-1982 |
通用带蜗杆的线材或带材制金属卡箍 |
(HOSE CLAMPS (WORM DRIVE TYPE) FOR GENERAL PURPOSE USE WITH BANDS OR WIRES.) |
| NF E27-853-1989 |
通用金属卡箍.带型，无螺钉，不可重复使用 |
(Metallic hose clamps for general purpose. Band type, without screws, non re-usable. Specifications.) |
| NF E27-854-1982 |
通用金属卡箍.带型,无螺钉,可重复使用的销钉卡箍或轴的卡箍 |
(METAL-HOSE CLAMPS FOR GENERAL PURPOSES ; BAND TYPE,WITHOUT SCREWS,RE-USABLE,PIN OR AXLE CLAMPS.) |
| NF E27-951-2000 |
钢丝钉.第1部分:一般用途的散装钉 |
(Steel wire nails - Part 1 : loose nails for general applications.) |
| NF E27-952-1974 |
常用扒钉 |
(VENTER HOOKS FOR GENERAL USE.) |
| NF E28-011-1936 |
传动轴润滑环 |
(LUBRICATION RING FOR DRIVING SHAFT.) |
| NF E28-201-1967 |
润滑装置.铰链盖滑脂塞 |
(FLIP TOP LUBRICATOR.) |
| NF E28-202-1967 |
润滑装置.转动盖滑脂塞 |
(OIL PLUGS WITH ROTATING CAPS.) |
| NF E28-204-1967 |
润滑装置.帽罩式油环 |
(STAUFFER LUBRICATORS.) |
| NF E28-205-1967 |
润滑装置.滑油液面计 |
(OIL LEVEL.) |
| NF E29-000-1996 |
管件.标准压力的定义和选择(欧洲标准EN 1333) |
(Pipework components. Definition and selection of pn.) |
| NF E29-003-1969 |
阀门关闭方向（闸板式阀门，阀式开关等） |
(DIRECTION OF CLOSURE FOR COCKS AND VALVES (SLUICE VALVES,SCREW DOWN VALVES,ETC.).) |
| NF E29-008-1972 |
管道.压力和温度.２３％镍和４％锰奥氏体球墨合金铸铁部件 |
(TEMPERATURE AND PRESSURE LIMITATIONS FOR PIPING SYSTEMS MANUFACTURED FROM 23% NICKEL 4% MANGANESE SPHEROIDAL GRAPHITE AUSTENITIC CAST IRON`.) |
| NF E29-009-1972 |
管道.压力和温度.２０％镍和２％铬奥氏体球墨合金铸铁部件 |
(TEMPERATURE AND PRESSURE LIMITATIONS FOR PIPING SYSTEMS MANUFACTURED FROM 20% NICKEL 2% CHROMIUM SPHEROIDAL GRAPHITE AUSTENITIC CAST IRON`.) |
| NF E29-011-1983 |
管道的术语和定义 |
(PIPEWORK. TERMS AND DEFINITION.) |
| NF E29-018-1986 |
工业管道.凹面或凸面连接的法兰盘连接环.ＩＳＯ标准压力为２．５到５０ |
(Industrial pipework. Bracing rings for flanges with female (groove or spigot), or male(tongue or spigot) faces. ISO PN 2,5 to ISO PN 50.) |
| NF E29-019-1985 |
工业阀门制造.可拆卸的栓接法兰盘.规范 |
(Industrial valves. Threaded detachable flanges. Specifications.) |
| NF E29-032-1985 |
工业管道.钢制构件.对焊接头.准备 |
(Industrial pipework. Steel components. Butt welding ends. Preparation.) |
| NF E29-033-1994 |
地下热水管道网络的隔热管道系统.钢制供水管道聚氨基甲酸乙酯热绝缘材料及高密度聚乙烯外壳的连接组件 |
(Preinsulated bonded pipe systems for underground hot water networks. Joint assembly for steel service pipes, polyurethane thermal insulation and outer casing of polyethylene.) |
| NF E29-041-1994 |
工业管道.减缩的螺栓柄.规范 |
(INDUSTRIAL PIPEWORK. REDUCED SHANK BOLTS. SPECIFICATIONS.) |
| NF E29-042-1-2000 |
法兰及其接头.螺栓连接.第1部分:螺栓连接的选择 |
(Flanges and their joints - Bolting - Part 1 : selection of bolting.) |
| NF E29-042-2-2002 |
法兰及其连接件.螺栓连接.第2部分:钢制法兰用螺栓料的分类.PN标识的 |
(Flanges and their joints - Bolting - Part 2 : classification of bolt materials for steel flanges, PN designated.) |
| NF E29-043-1990 |
工业管道工程.管道、锅炉和压力容器法兰组件用非合金钢或合金钢制螺栓 |
(Industrial pipework. Non alloy and alloy. Steel bolting for flanged assemblies of pipeworks, boilers and pressure vessels. Specifications.) |
| NF E29-064-1946 |
阀门制造.带活门的关闭阀.建筑物内阀门制造的专门术语 |
(INDUSTRIAL VALVES. SCREW-DOWN STOPVALVES. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.) |
| NF E29-065-1946 |
阀门制造.带活门的抽水阀门.建筑物内阀门制造的专门术语 |
(INDUSTRIAL VALVES. TAPS. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.) |
| NF E29-066-1946 |
阀门制造抽汲阀.转动式吸入阀和关闭阀.建筑物内阀门制造的专门术语 |
(INDUSTRIAL VALVES. DRAW-OFF COCKS AND STOPCOCKS. TERMINOLOGY RELATING PARTICULARLY TO THE BUILDING TRADE.) |
| NF E29-134-1978 |
家用管道燃气设备用带节气阀并与阳端Ｇ１／２相连的双连式安全开关 |
(SAFETY RELEASE DEVICES WITH BUILT-IN STOP TAP AND TWO G 1/2 MALE UNION CONNECTIONS FOR DOMESTIC APPLIANCES USING MAINS GAS FUELS.) |
| NF E29-135/A1-1987 |
NF E 29-135-1973的修改件1 |
() |
| NF E29-138-1978 |
煤气用具控制用，锥形转动，有装配式铜管路带法兰和Ｇ１／２连接管节的角形墙壁阀 |
(FLANGED WALL VALVES,AT RIGHT ANGLES,FOR CONTROLLING GAS APPLIANCES,WITH TAPERED ROTATING SECTION,FOR BUILT-IN BRASS PIPING AND WITH G 1/2 CONNECTION.) |
| NF E29-139-1998 |
建筑物气体装置用手工操作球阀和死底锥形旋塞 |
(Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings.) |
| NF E29-161-1943 |
支流阀.关闭阀和给水阀.总则.公称压力.标准压力１０ |
(BRANCH PIPE VALVES. STOPCOCKS AND DRAW-OFF COCKS. GENERAL. NOMINAL PRESSURE PN 10.) |
| NF E29-162-1943 |
支流阀.关闭阀.公称压力，标准压力１０ |
(BRANCH PIPE VALVES. STOPCOCKS. NOMINAL PRESSURE PN 10.) |
| NF E29-163-1943 |
支流阀.给水阀.公称压力，标准压力１０ |
(BRANCH PIPE VALVES. DRAW-OFF COCKS. NOMINAL PRESSURE PN 10.) |
| NF E29-171-1999 |
入口压力最大达100bar的气压调节器 |
(Gas pressure regulators for inlet pressures up to 100 bar.) |
| NF E29-171/A1-2001 |
入口压力100巴以下的气体压力调节器 |
(Gas pressure regulators for inlet pressures up to 100 bar.) |
| NF E29-175-2003 |
气体压力调节站和装置用安全设备.用于入口压力最高达100bar的气体安全关闭装置 |
(Safety devices for gas pressure regulating stations and installations - Gas safety shut-off devices for inlet pressures up to 100 bar.) |
| NF E29-179-2002 |
入口压力达100巴的压力调节器和相关安全装置用弹性体 |
(Elastomers for gas pressure regulators and associated safety devices for inlet pressures up to 100 bar.) |
| NF E29-200-1-2002 |
法兰及其连接件.按PN标注的管、阀门、配件和附件用圆形法兰.钢法兰 |
(Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 1 : steel flanges.) |
| NF E29-200-4-2002 |
法兰及其连接件.按PN标注的管、阀门、配件和附件用圆形法兰.第4部分:铝合金法兰 |
(Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4 : aluminium alloy flanges.) |
| NF E29-204-1992 |
工业管道系统.锻制钢法兰和套圈.材料.机械性能.制造.试验 |
(Industrial pipeworks. Forged steel flanges and collars. Materials. Mechanical properties. Fabrication. Tests.) |
| NF E29-207-1986 |
工业管道.合金钢法兰盘和卡环及复合材料法兰盘.术语，尺寸，规范 |
(INDUSTRIAL PIPEWORK. COPPER ALLOYS FLANGES AND COLLARS AND COMPOSITE FLANGES. TERMINOLOGY. DIMENSIONS. SPECIFICATIONS.) |
| NF E29-210-1985 |
工业管道.差动压力装置用有孔法兰 |
(INDUSTRIAL PIPEWORK. ORIFICE FLANGES FOR DIFFERENTIAL PRESSURE DEVICES.) |
| NF E29-220-1986 |
工业管道.管道用衔接器和带法兰的可调垫圈.规范 |
(INDUSTRIAL PIPEWORK. FLANGED ADAPTERS AND DISASSEMBLY SEAL FOR PIPEWORK. SPECIFICATIONS.) |
| NF E29-251-1972 |
工业管道.不锈钢制焊接冲压凸缘（薄型系列）.公称压力１０ |
(STAMPED STAINLESS-STEEL FILLETS FOR WELDING (THIN SERIES) PN 10) |
| NF E29-260-1987 |
工业管道.涂PTFE-FEP-PFA碳氟化树脂的管道构件 |
(Industrial pipes. Pipe components with PTFE - FEP - PFA fluorocarbon resin.) |
| NF E29-300-3-2003 |
阀门.外壳设计强度.第3部分:实验方法 |
(Valves - Shell design strength - Part 3 : experimental method.) |
| NF E29-301-1-2000 |
工业阀门.对焊尾阀一端到另一端和中心到端面的尺寸 |
(Industrial valves - End-to-end and centre-to-end dimensions for butt welding end valves.) |
| NF E29-302-1-1996 |
法兰管系统使用的金属阀.面至面和中心至面的尺寸.第1部分:PN-指定阀 |
(Industrial valves. Face-to-face and centre-to-face dimensions of matal valves for use in flanged pipe systems. Part 1 : pn-designated valves.) |
| NF E29-302-2-1996 |
工业配件.安装在带法兰的管道中的金属配件结构长度.第2部分:按级别标识的配件 |
(Industrial valves. Face-to-face and centre-to-face dimensions of metal valves for use in flanged pipe systems. Part 2 : class-designated valves.) |
| NF E29-303-1-2000 |
阀门.阀体、阀盖和阀套用材料.第1部分:欧洲标准中规定的钢 |
(Valves - Materials for bodies, bonnets and covers - Part 1 : steels specified in European Standards.) |
5分钟获取标准报价 咨询电话：010-6973-5438 QQ：31794-7760 MSN:wwtrans#126.com