标准号 |
中文名称 |
英文名称 |
ASTM D 4625-1992 |
馏分燃料在43℃(100°F)贮存稳定性的试验方法 |
Test Method for Distillate Fuel Storage Stability at 43 Degrees C (110 Degrees F) |
ASTM D 4626-1995 |
气相色谱响应因子的计算 |
Calculation of Gas Chromatographic Response Factors |
ASTM D 4627-1992 |
水溶性金属加工液铁片腐蚀试验方法 |
Test Method for Iron Chip Corrosion for Water-Dilutable Metalworking Fluids |
ASTM D 4628-1997 |
原子吸收光谱法分析未用润滑油中钡、钙、镁和锌的试验方法 |
Test Method for Analysis of Barium, Calcium, Magnesium and Zinc in Unused Lubricating Oils by Atomic Absorption Spectrometry |
ASTM D 4629-1996 |
氧化燃烧和化学发光法测定液态石油烃中痕量有机结合氮的试验方法 |
Test Method for Trace Nitrogen in Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and Chemiluminescence Detection |
ASTM D 4630-1996 |
用恒定水头喷射试验现场测定低渗透性岩石的透过比和释水系数的标准试验方法 |
Standard Test Method for Determining Transmissivity and Storage Coefficient of Low-Permeability Rocks by In Situ Measurements Using the Constant Head Injection Test |
ASTM D 4631-1995 |
用压力脉冲技术现场测量低渗透性岩石的透过比和释水系数的试验方法 |
Test Method for Determining Transmissivity and Storativity of Low Permeability Rocks by In Situ Measurements Using the Pressure Pulse Technique |
ASTM D 4632-1991 |
土工织物的断裂荷载和延伸度的试验方法 |
Test Method for Grab Breaking Load and Elongation of Geotextiles |
ASTM D 4633-1986 |
用动力贯入器试验系统测量应力波能的试验方法 |
Test Method for Stress Wave Energy Measurement for Dynamic Penetrometer Testing Systems |
ASTM D 4634-1986 |
苯代丁烯二酸酐挤压料 |
Styrene-Maleic Anhydride Materials (S/MA) |
ASTM D 4635-2001 |
通用和包装用低密度聚乙烯薄膜标准规范 |
Standard Specification for Polyethylene Films Made from Low-Density Polyethylene for General Use and Packaging Applications |
ASTM D 4636-1999 |
液压油、飞机涡轮发动机润滑油和其他高精炼油的腐蚀性和氧化稳定性的试验方法 |
Standard Test Method for Corrosiveness and Oxidation qualility of Hydraulic Oils, Aircraft Turbine Engine Lubricants, and Other Highly Refined Oils |
ASTM D 4637-1996 |
单层屋面膜用硫化橡胶板 |
Vulcanized Rubber Sheet Used in Single-Ply Roof Membrane |
ASTM D 4638-1995 |
无机化学分析用生物学样品的制备 |
Preparation of Biological Samples for Inorganic Chemical Analysis |
ASTM D 4639-1986 |
酚醛树脂中挥发物含量的试验方法 |
Test Method for Volatile Content in Phenolic Resins |
ASTM D 464-1995 |
松脂油产品包括妥尔油和其他相关产品的皂化值的试验方法 |
Test Methods for Saponification Number of Naval Store Products Including Tall Oil and Other Related Products |
ASTM D 4640-1986 |
热固性酚醛树脂冲击固化时间的测定 |
Test Method for Determining Stroke Cure Time of Thermosetting Phenol-Formaldehyde Resins |
ASTM D 4641-1994 |
由氮解吸等温线计算催化剂孔隙尺寸分布 |
Calculation of Pore Size Distributions of Catalysts from Nitrogen Desorption Isotherms |
ASTM D 4642-1992 |
湿化学法测定重整催化剂中铂的试验方法 |
Test Method for Platinum in Reforming Catalysts by Wet Chemistry |
ASTM D 4643-2000 |
微波炉法测定土壤中含水量的标准试验方法 |
Standard Test Method for Determination of Water (Moisture) Content of Soil by the Microwave Oven Method |
ASTM D 4644-1987 |
油页岩和类似软岩石潮解耐久性的试验方法 |
Test Method for Slake Durability of Shales and Similar Weak Rocks |
ASTM D 4645-1987 |
使用水压断裂法测定现场岩石应力的试验方法 |
Test Method for Determination of the In-Situ Stress in Rock Using the Hydraulic Fracturing Method |
ASTM D 4646-1987 |
24小时分批测量土壤和沉积物的污染物吸附作用的试验方法 |
Test Method for 24-h Batch-Type Measurement of Contaminant Sorption by Soils and Sediments |
ASTM D 4647-1993 |
用针孔试验作分散粘土的分类和识别方法 |
Test Method for Identification and Classification of Dispersive Clay Soils by the Pinhole Test |
ASTM D 4648-1994 |
饱和细粒粘性土壤的实验室小型十字板剪力试验方法 |
Test Method for Laboratory Miniature Vane Shear Test for Saturated Fine-Grained Clayey Soil |
ASTM D 4649-1995 |
伸展性、收缩性和网缠材料的选择 |
Selection of Stretch, Shrink and Net Wrap Materials |
ASTM D 465-2001 |
松脂制品包括妥尔油及其它相关产品酸值的标准试验方法 |
Standard Test Methods for Acid Number of Naval Stores Products Including Tall Oil and Other Related Products |
ASTM D 4650-1993 |
正丁烷热物理性能表 |
Normal Butane Thermophysical Property Tables |
ASTM D 4651-1993 |
异丁烷热物理性能表 |
Isobutane Thermophysical Property Tables |
ASTM D 4652-1992 |
电绝缘用硅酮液 |
Silicone Fluid Used for Electrical Insulation |
ASTM D 4653-1987 |
皮革中总氯化物的试验方法 |
Test Method for Total Chlorides in Leather |
ASTM D 4654-1987 |
皮革中硫酸盐盐基度的试验方法 |
Test Method for Sulfate Basicity in Leather |
ASTM D 4655-1995 |
皮革中硫酸盐的试验方法(中性酸和混合酸总含量) |
Test Methods for Sulfates in Leather (Total, Neutral and Combined Acid) |
ASTM D 4656-1995 |
汽车和小修用预稀释含水乙二醇(最小容积50%)基发动机冷却剂 |
Prediluted Aqueous Ethylene Glycol (50 Volume% Minimum) Base Engine Coolant for Automobiles and Light-Duty Service |
ASTM D 4657-1992 |
水中多环芳烃的试验方法 |
Test Method for Polynuclear Aromatic Hydrocarbons in Water |
ASTM D 4658-1992 |
水中亚硫酸盐离子的试验方法 |
Test Method for Sulfide Ion in Water |
ASTM D 4659-1998 |
聚氨酯原材料的试验方法:异氰酸酯比重的测定 |
Test Methods for Polyurethane Raw Materials: Determination of Specific Gravity of Isocyanates |
ASTM D 466-1942 |
沥青乳胶沉积薄膜的试验方法 |
Test Methods for Films Deposited From Bituminous Emulsions |
ASTM D 4660-1995 |
聚氨酯原料的试验方法:甲苯二异氰酸酯中同分异构体含量的测定 |
Test Methods for Polyurethane Raw Materials: Determination of the Isomer Content of Toluenediisocyanate |
ASTM D 4661-1998 |
聚氨酯原材料的试验方法:异氰酸酯中总氯化物含量的测定 |
Test Methods for Polyurethane Raw Materials: Determination of Total Chlorine in Isocyanates |
ASTM D 4662-1998 |
聚氨酯原材料的试验方法:多醇的酸、碱值的测定 |
Test Methods for Polyurethane Raw Materials: Determination of Acid and Alkalinity Numbers of Polyols |
ASTM D 4663-1998 |
聚氨酯原材料的试验方法:异氰酸酯的可水解氯的测定 |
Test Method for Polyurethane Raw Materials: Determination of Hydrolyzable Chlorine of Isocyanates |
ASTM D 4669-1998 |
聚氨酯原材料的试验方法:多醇比重的测定 |
Test Method for Polyurethane Raw Materials: Determination of Specific Gravity of Polyols |
ASTM D 4670-1997 |
聚氨酯原材料的试验方法:多醇中悬浮物的测定 |
Test Method for Polyurethane Raw Materials: Determination of Suspended Matter in Polyols |
ASTM D 4671-1999 |
聚氨基甲酸乙酯原材料的试验方法:多醇不饱和性的测定 |
Test Method for Polyurethane Raw Materials: Determination of Unsaturation of Polyols |
ASTM D 4672-1995 |
聚氨酯原材料的试验方法:多醇含水量的测定 |
Test Methods for Polyurethane Raw Materials: Determination of Water Content Polyols |
ASTM D 4673-1998 |
丙烯腈-丁二烯-苯乙烯共聚物(ABS)模压和挤压材料 |
Acrylonitrile-Butadiene-Styrene (ABS) Molding and Extrusion Materials |
ASTM D 4674-1989 |
加速试验暴露在室内萤光灯和透窗入室内的日光下塑料的颜色稳定性的试验方法 |
Test Method for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Fluorescent Lighting and Window-Filtered Daylight |
ASTM D 4675-2000 |
扁平皮带材料选择和使用的标准指南 |
Standard Guide for Selection and Use of Flat Strapping Materials |
ASTM D 4676-1994 |
橡胶配料-苯二胺抗降解剂的描述 |
Description of Rubber Compounding Materials p-Phenylenediamine Antidegradants |
ASTM D 4677-1987 |
橡胶配料的分类-二氧化钛 |
Classification for Rubber Compounding Materials - Titanium Dioxide |
ASTM D 4678-1994 |
橡胶-工业参考材料(IRM)的准备、试验、验收和文献加工 |
Rubber - Preparation, Testing, Acceptance and Documentation for Industry Reference Materials (IRM) |
ASTM D 4679-2002 |
一般用途、家用或护肤用橡胶手套的标准规范 |
Standard Specification for Rubber General Purpose, Household or Beautician Gloves |
ASTM D 4680-1998 |
用压力负荷法(木材对木材)对胶粘剂静剪切的蠕变和破坏时间的试验方法 |
Test Method for Creep and Time to Failure of Adhesives in Static Shear by Compression Loading (Wood-to-Wood) |
ASTM D 4682-1987 |
二冲程循环汽油发动机润滑剂的流动性及与汽油的可混合性 |
Miscibility with Gasoline and Fluidity of Two-Stroke-Cycle Gasoline Engine |
ASTM D 4683-1996 |
锥形承载模拟器在高剪切率和高温下测定粘度的试验方法 |
Test Method for Measuring Viscosity at High Shear Rate and High Temperature by Tapered Bearing Simulator |
ASTM D 4684-1999 |
机油在低温下表观粘度和弯曲应力测定的试验方法 |
Test Method for Determination of Yield Stress and Apparent Viscosity of Engine Oils at Low Temperature |
ASTM D 4686-1991 |
频率分布的识别和转换 |
Identification and Transformation of Frequency Distributions |
ASTM D 4687-1995 |
废料取样一般计划的制定 |
General Planning of Waste Sampling |
ASTM D 4688-1999 |
评定榫接木材粘结用结构胶粘剂的标准试验方法 |
Standard Test Methods for Evaluating Structural Adhesives for Finger Jointing Lumber |
ASTM D 4689-1999 |
酪蛋白型胶粘剂 |
Adhesive, Casein-Type |
ASTM D 4690-1999 |
脲甲醛树脂胶粘剂 |
Urea-Formaldehyde Resin Adhesives |
ASTM D 4691-1996 |
火焰原子吸收分光光度法测定水中素 |
Measuring Elements in Water by Flame Atomic Absorption Spectrophotometry |
ASTM D 4692-2001 |
反渗透用硫酸盐类换算盐分(CaSO4,SrSO4和BaSO4)计算和校正的标准实施规程 |
Standard Practice for Calculation and Adjustment of Sulfate Scaling Salts (CaSO4, SrSO4, and BaSO4) for Reverse Osmosis and Nanofiltration |
ASTM D 4693-1997 |
润滑脂润滑的车轮轴承低温扭转试验方法 |
Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings |
ASTM D 4694-1996 |
落重型脉冲负荷装置挠曲的试验方法 |
Test Method for Deflections with a Falling-Weight-Type Impulse Load Device |
ASTM D 4695-1996 |
普通路面弯曲测量 |
General Pavement Deflection Measurements |
ASTM D 4696-1992 |
从渗流区进行孔隙液体取样的标准导则 |
Standard Guide for Pore-Liquid Sampling from the Vadose Zone |
ASTM D 4697-1995 |
在用户实验室维护的试验方法 |
Maintaining Test Methods in the Users Laboratory |
ASTM D 4698-1992 |
各种金属的化学分析用沉淀物样品的总煮解度的试验方法 |
Total Digestion of Sediment Samples for Chemical Analysis of Various Metals |
ASTM D 4699-1999 |
大颗粒催化剂振动存储密度的标准试验方法 |
Standard Test Method for Vibratory Packing Density of Large Formed Catalyst and Catalyst Particles |
ASTM D 470-1999 |
电线和电缆用交联绝缘与套管的试验方法 |
Test Methods for Crosslinked Insulations and Jackets for Wire and Cable |
ASTM D 4700-1991 |
渗流区的土壤抽样 |
Soil Sampling from the Vadose Zone |
ASTM D 4701-2000 |
技术级氯甲烷的标准规范 |
Standard Specification for Technical Grade Methylene Chloride |
ASTM D 4702-1997 |
与现行的ASTM标准一致的检验横切、导向杆和麻花钻机械钻煤取样装置 |
Inspecting Crosscut, Sweep-Arm and Auger Mechanical Coal-Sampling Systems for Conformance with Current ASTM Standards |
ASTM D 4703-1993 |
由热塑性材料压缩模制的试样、瓷花金属板及薄板 |
Compression Molding Thermoplastic Materials into Test Specimens, Plaques or Sheets |
ASTM D 4704-1993 |
皮革的撕破强度和切口撕破的试验方法 |
Test Method for Tearing Strength, Tongue Tear of Leather |
ASTM D 4705-1993 |
革皮、双孔缝合时抗扯裂强度的试验方法 |
Test Method for Stitch Tear Strength of Leather, Double Hole |
ASTM D 4706-1993 |
酚醛树脂中羟甲基组团定性测定的试验方法 |
Test Method for Qualitative Determination of Methylol Group in Phenolic Resins |
ASTM D 4707-1997 |
测量辊涂机耐涂料喷溅的试验方法 |
Test Method for Measuring Paint Spatter Resistance to Roller Application |
ASTM D 4708-1999 |
有机覆层的均匀游离膜的制备 |
Preparation of Uniform Free Films of Organic Coatings |
ASTM D 4709-1993 |
丙烯酸甲酯 |
Methyl Acrylate |
ASTM D 471-1998 |
液体对橡胶性能影响的试验方法 |
Test Method for Rubber Property - Effect of Liquids |
ASTM D 4710-1993 |
乙醛 |
Acetaldehyde |
ASTM D 4711-1989 |
烷基苯磺酸中磺酸与硫酸的试验方法 |
Test Method for Sulfonic and Sulfuric Acids in Alkylbenzene Sulfonic Acids |
ASTM D 4712-1987 |
工业用水的检验.可还原涂层 |
Testing Industrial Water-Reducible Coatings |
ASTM D 4713-1992 |
印刷油墨、乳状树脂和涂料中不挥发成分的试验方法 |
Test Methods for Nonvolatile Content of Heatset and Liquid Printing Ink Systems |
ASTM D 4714-1996 |
测定湿热对纸和纸板特性的影响的试验方法(额定湿度为50%,温度为90℃) |
Test Method for Determination of Effect of Moist Heat (50% Relative Humidity and 90 Degrees C) on Properties of Paper and Board |
ASTM D 4715-1998 |
测定焦油和硬沥青焦化值的试验方法(Alcan) |
Standard Test Method for Coking Value of Tar and Pitch (Alcan) |
ASTM D 4716-2000 |
土工织物及其有关产品的恒定水头液压透过比(在平面流中)的标准试验方法 |
Standard Test Method for Determining the (In-plane) Flow Rate per Unit Width and Hydraulic Transmissivity of a Geosynthetic Using a Constant Head |
ASTM D 4718-1987 |
含有超大颗粒土壤的单位重量和含水量修正办法 |
Correction of Unit Weight and Water Content for Soils Containing Oversize Particles |
ASTM D 4719-2000 |
检验土壤用预打孔压力计的标准试验方法 |
Standard Test Method for Prebored Pressuremeter Testing in Soils |
ASTM D 4720-1987 |
软窗帘的性能评定 |
Evaluation of the Performance of Soft Window Coverings |
ASTM D 4721-1989 |
可机器洗涤的和干洗的床罩与附属品性能的评定 |
Evaluation of the Performance of Machine Washable and Drycleanable Bedcoverings and Accessories |
ASTM D 4723-1999 |
纺织品耐热性和易燃性试验方法和性能规范的描述和标准索引 |
Standard Index of and Descriptions of Textile Heat and Flammability Test Methods and Performance Specifications |
ASTM D 4724-1999 |
用针入法测试线纱缠结度的标准试验方法 |
Standard Test Methods for Degree of Filament Yarn Entanglement by Needle Insertion Methods |
ASTM D 4725-1998 |
发动机冷却剂术语 |
Terminology for Engine Coolants |
ASTM D 4726-2001 |
装配门窗用硬质聚氯乙烯(PVC)外部挤压型材的标准规范 |
Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors |
ASTM D 4727/D 4727M-1998 |
瓦拢面的和实心的纤维板坯料(包装级)和切制形材 |
Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes |
ASTM D 4728-2001 |
运输集装箱随机振动检测的标准试验方法 |
Standard Test Method for Random Vibration Testing of Shipping Containers |
ASTM D 4729-1987 |
使用扁千斤顶法现场测定变形应力和模数的试验方法 |
Test Method for In Situ Stress and Modulus of Deformation Using the Flatjack Method |
ASTM D 473-1981 |
萃取法测定原油和燃料油中沉积物的试验方法 |
Test Method for Sediment in Crude Oils and Fuel Oils by the Extraction Method |
ASTM D 4730-1993 |
电信电线和电缆用浸渍化合物 |
Flooding Compounds for Telecommunications Wire and Cable |
ASTM D 4731-1993 |
电信电线和电缆用热充填化合物 |
Hot-Application Filling Compounds for Telecommunications Wire and Cable |
ASTM D 4732-1993 |
电信电线和电缆用冷充填化合物 |
Cool-Application Filling Compounds for Telecommunications Wire and Cable |
ASTM D 4733-1998 |
无溶剂电绝缘清漆试验方法 |
Test Methods for Solventless Electrical Insulating Varnishes |
ASTM D 4734-1998 |
精制545-苯 |
Refined Benzene-545 |
ASTM D 4735-1996 |
用气相色谱法测定精制苯中微量噻吩的试验方法 |
Test Method for Determination of Trace Thiophene in Refined Benzene by Gas Chromatography |
ASTM D 4737-1996 |
用四变量方程计算十六烷指数的试验方法 |
Test Method for Calculated Cetane Index by Four Variable Equation |
ASTM D 4738-1990 |
使用光基准线法对立式圆柱形容器的校验 |
Calibration of Upright Cylindrical Tanks Using the Optical Reference Line Method |
ASTM D 4739-1996 |
电势滴定法测定碱值的试验方法 |
Test Method for Base Number Determination by Potentiometric Titration |
ASTM D 4740-1995 |
用点滴试验法对残余燃料稳定性和兼容性的试验方法 |
Test Method for Stability and Compatibility of Residual Fuels by Spot Test |
ASTM D 4741-1996 |
高温和高剪切速率下用锥塞粘度计测量粘度的试验方法 |
Test Method for Measuring Viscosity at High Temperature and High Shear Rate by Tapered-Plug Viscometer |
ASTM D 4742-1996 |
用薄膜氧吸收法对汽车发动机油氧化稳定性的试验方法 |
Test Method for Oxidation Stabiliy of Gasoline Automotive Engine Oils by Thin-Film Oxygen Uptake (TFOUT) |
ASTM D 4743-1992 |
溶解水成沉积物用溶解装置功效的试验方法 |
Test Method for Efficacy of Solvent Systems for Dissolving Water-Formed Deposits |
ASTM D 4744-1989 |
用炭吸收微库仑检测法对水中有机卤化物的试验方法 |
Test Method for Organic Halides in Water by Carbon Adsorption-Microcoulometric Detection |
ASTM D 4745-1997 |
聚四氟乙烯模塑和挤压材料的填充化合物 |
Filled Compounds of Polytetrafluoroethylene (PTFE) Molding and Extrusion Materials |
ASTM D 4746-1998 |
用加压过滤法测定焦油和硬沥青中喹啉不溶物含量的试验方法 |
Test Method for Determination of Quinoline Insolubles (QI) in Tar and Pitch by Pressure Filtration |
ASTM D 4747-2002 |
用气液色谱法测定乳胶中未反应单体含量的标准试验方法 |
Standard Test Method for Determining Unreacted Monomer Content of Latexes Using Gas-Liquid Chromatography |
ASTM D 4748-1998 |
使用短脉冲雷达测定粘合路面层厚度的试验方法 |
Test Method for Determining the Thickness of Bound Pavement Layers Using Short-Pulse Radar |