标准号 |
中文名称 |
英文名称 |
ISO 7781-2001 |
丁苯生橡胶.皂和有机酸含量的测定 |
Styrene-butadiene rubber, raw - Determination of soap and organic-acid content |
ISO 7783-1 Technical Corrigendum 1-1998 |
涂料和清漆.水蒸气渗透率的测定.第1部分:无涂层用压痕法.技术勘误1 |
Paints and varnishes - Determination of water-vapour transmission rate - Part 1: Dish method for free films; Technical Corrigendum 1 |
ISO 7783-1-1996 |
涂料和清漆.水蒸气渗透率的测定.第1部分:无涂层用碟法 |
Paints and varnishes - Determination of water-vapour transmission rate - Part 1: Dish method for free films |
ISO 7783-2-1999 |
涂料和清漆.外部砖石工程和混凝土用涂覆材料和涂覆系统.第2部分:水蒸气渗透率的测定和分类 |
Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 2: Determination and classification of water-vapour transmission rate (permeability) |
ISO 7784-1-1997 |
涂料和清漆.耐磨性的测定.旋转磨擦纸盖轮法 |
Paints and varnishes - Determination of resistance to abrasion - Rotating abrasive-paper-covered wheel method |
ISO 7784-2-1997 |
涂料和清漆.耐磨性的测定.旋转磨擦橡胶轮法 |
Paints and varnishes - Determination of resistance to abrasion - Part 2: Rotating abrasive rubber wheel method |
ISO 7784-3-2000 |
涂料和清漆.耐磨性的测定.第3部分:往复式试验用样板法 |
Paints and varnishes - Determination of resistance to abrasion - Part 3: Reciprocating test panel method |
ISO 7785-1-1997 |
手持式牙科器械.第1部分:高速空气涡轮钻头 |
Dental handpieces - Part 1: High-speed air turbine handpieces |
ISO 7785-2-1995 |
手持式牙科器械.第2部分:平角和啮合角手持式器械 |
Dental handpieces - Part 2: Straight and geared angle handpieces |
ISO 7786-2001 |
牙科用旋转器械.实验室研磨器械 |
Dental rotary instruments - Laboratory abrasive instruments |
ISO 7787-1-1984 |
牙科用旋转器械.切割刀具.第1部分:实验室用钢质刀具 |
Dental rotary instruments; Cutters; Part 1 : Steel laboratory cutters |
ISO 7787-2-2000 |
牙科用旋转器械.切割器.第2部分:实验室用硬质合金切割器 |
Dental rotary instruments - Cutters - Part 2: Carbide laboratory cutters |
ISO 7787-3-1991 |
牙科用旋转器械.切割工具.第3部分:铣床用硬质合金刀具 |
Dental rotary instruments; cutters; part 3: carbide laboratory cutters for milling machines |
ISO 7787-4-2002 |
牙科用旋转器械.切割刀具.第1部分:实验室用小型硬质合金刀具 |
Dental rotary instruments - Cutters - Part 4: Miniature carbide laboratory cutters |
ISO 7788-1985 |
钢.热轧钢板和宽扁钢板的表面光洁度.交货要求 |
Steel; Surface finish of hot-rolled plates and wide flats; Delivery requirements |
ISO 7789 Technical Corrigendum 1-1999 |
液压动力.2,3,4通道螺纹及芯阀.空腔.技术勘误1 |
Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities; Technical Corrigendum 1 |
ISO 7789-1998 |
液压动力-插装式阀二,三和四口螺纹.空腔 |
Hydraulic fluid power - Two-, three- and four-port screw-in cartridge valves - Cavities |
ISO 779-2001 |
纸、纸板和纸浆.铁的测定 |
Paper, board and pulp - Determination of iron |
ISO 7790-1997 |
液压传动.规格为03和05型的四油口标准设计叠阀和四油口定向控制阀.紧固尺寸 |
Hydraulic fluid power - Four-port modular stack valves and four-port directional control valves, sizes 02, 03 and 05 - Clamping dimensions |
ISO 7792-1-1997 |
塑料.热塑聚酯(TP)模塑和挤压材料.第1部分:命名体制和基本规范 |
Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 1: Designation system and basis for specifications |
ISO 7792-2-1997 |
塑料.热塑聚酯(TP)模塑和挤压材料.第2部分:试样的制备和性质的测定 |
Plastics - Thermoplastic polyester (TP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties |
ISO 7794-1991 |
越野雪橇.雪橇紧固螺钉.要求 |
Cross-country skis; ski binding screws; requirements |
ISO 7795-1994 |
越野雪撬.雪撬紧固螺钉.试验方法 |
Cross-country skis - Ski-binding screws - Test methods |
ISO 7796-1985 |
滑雪板.几何形状.测量条件 |
Skis; Geometry; Measuring conditions |
ISO 7797-1985 |
越野雪橇.准静态载荷在断裂载荷和弯曲时的测定 |
Cross-country skis; Determination of breaking load and deflection at break with quasistatic load |
ISO 7798-1984 |
越野雪橇.疲劳指标的测定.周期性载荷试验 |
Cross-country skis; Determination of fatigue indexes; Cyclic loading test |
ISO 7799-1985 |
金属材料.厚度3mm或小于3mm的板材或带材.反向弯曲试验 |
Metallic materials; Sheet and strip 3 mm thick or less; Reverse bend test |
ISO 78-2-1999 |
化学.标准样本.第2部分:化学分析方法 |
Chemistry - Layouts for standards - Part 2: Methods of chemical analysis |
ISO 78-3-1983 |
化学.标准的编制.第3部分:分子吸收光谱测定法标准 |
Chemistry; Layouts for standards; Part 3: Standard for molecular absorption spectrometry |
ISO 78-4-1983 |
标准的编制.第4部分:原子吸收光谱测定的分析标准 |
Layouts for standards; Part 4 : Standard for atomic absorption spectrometric analysis |
ISO 780-1997 |
包装.货物搬运的图形标志 |
Packaging - Pictorial marking for handling of goods |
ISO 7800-1984 |
金属材料.线材.单纯扭转试验 |
Metallic materials; Wire; Simple torsion test |
ISO 7800-2003 |
金属材料.线材.单向扭转试验 |
(Metallic materials - Wire - Simple torsion test) |
ISO 7800-2003 |
金属材料.线材.单向扭转试验 |
|
ISO 7801-1984 |
金属材料.线材.反向弯曲试验 |
Metallic materials; Wire; Reverse bend test |
ISO 7802-1983 |
金属材料.线材.缠绕试验 |
Metallic materials; Wire; Wrapping test |
ISO 7803-1987 |
商业用道路车辆.转向球接头 |
Commercial road vehicles; Steering ball joints |
ISO 7804-1985 |
商业用道路车辆.载重汽车动力输出装置的侧口 |
Commercial road vehicles; Side openings for truck power take-offs |
ISO 7805-1-1984 |
工业用板筛.第1部分:3mm及其以上的厚度 |
Industrial plate screens; Part 1 : Thickness of 3 mm and above |
ISO 7805-2-1987 |
工业用板筛.第2部分:3mm以下的厚度 |
Industrial plate screens; Part 2 : Thickness below 3 mm |
ISO 7806-1983 |
工业用板筛.孔目符号标示法 |
Industrial plate screens; Codification for designating perforations |
ISO 7807-1983 |
空气配给.有锁紧型旋焊的圆形薄金属管和矩形薄金属管.尺寸 |
Air distribution; Straight circular sheet metal ducts with a lock type spiral seam and straight rectangular sheet metal ducts; Dimensions |
ISO 7808-1992 |
塑料.热固性注塑塑料.输送流动性 |
Plastics; thermosetting moulding materials; determination of transfer flow |
ISO 7809 ADD 1-1987 |
第1次补充 |
Addendum 1-1987 |
ISO 7809 ADD 2-1987 |
第2次补充 |
Addendum 2-1987 |
ISO 7812 Technical Corrigendum 1-1988 |
识别卡.发行者鉴定器的标准号系统和登记程序.技术勘误表1 |
Identification cards; numbering system and registration procedure for issuer identifiers; technical corrigendum 1 |
ISO 7812-1987 |
识别卡.发行者鉴定器的标准号系统和登记程序 |
Identification cards; Numbering system and registration procedure for issuer identifiers |
ISO 7822-1990 |
玻璃纤维增强塑料.空隙量测定.灼烧损失、机械粉碎和统计计数法 |
Textile glass reinforced plastics; determination of void content; loss on ignition, mechanical disintegration and statistical counting methods |
ISO 7823-1-1998 |
塑料.聚甲基丙烯酸甲酯薄板材.类型、尺寸和特性.第1部分:铸造薄板材 |
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 1: Cast sheets |
ISO 7823-1-2003 |
塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第1部分:浇注薄板材 |
(Plastics - Poly(methyl methacrylate) sheets; Types, dimensions and characteristics - Part 1: Cast sheets) |
ISO 7823-1-2003 |
塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第1部分:浇注薄板材 |
|
ISO 7823-2-1996 |
塑料.聚甲基丙烯酸甲酯的类型,尺寸和性能.;第2部分:熔压挤出片 |
Plastics - Poly(methyl methacrylate) sheets - Types, dimensions and characteristics - Part 2: Melt-calendered extruded sheets |
ISO 7823-2-2003 |
塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和性能.第2部分:挤出薄板材 |
(Plastics - Poly(methyl methacrylate) sheets; Types, dimensions and characteristics - Part 2: Extruded sheets) |
ISO 7823-2-2003 |
塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和性能.第2部分:挤出薄板材 |
|
ISO 7823-3-2003 |
塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第1部分:连续浇注薄板材 |
(Plastics - Poly(methyl methacrylate) sheets; Types, dimensions and characteristics - Part 3: Continuous cast sheets) |
ISO 7823-3-2003 |
塑料.聚甲基丙烯酸甲酯板材.类型、尺寸和特性.第3部分:连续浇注薄板材 |
|
ISO 7824-1986 |
造船和海上建筑物.润滑油管嘴.锥型和扁平型 |
Shipbuilding and marine structures; Lubrication nipples; Cone and flat types |
ISO 7825-1985 |
造船.甲板机械.一般要求 |
Shipbuilding; Deck machinery; General requirements |
ISO 7827-1994 |
水质.含水介质中有机物的充分需氧生物降解性评定.溶解有机碳分析法 |
Water quality - Evaluation in an aqueous medium of the ultimate aerobic biodegradability of organic compounds - Method by analysis of dissolved organic carbon (DOC) |
ISO 7828-1985 |
水质.生物取样法.水生海底大型无脊椎动物手网取样指南 |
Water quality; Methods of biological sampling; Guidance on handnet sampling of aquatic benthic macro-invertebrates |
ISO 7829 Technical Corrigendum 1-2001 |
摄影技术.航空照相机用黑白胶片.ISO感光度平均梯度的测定.技术勘误1 |
Photography - Black-and-white aerial camera films - Determination of ISO speed and average gradient; Technical Corrigendum 1 |
ISO 7829-1986 |
摄影技术.航空照相机用黑白胶片.ISO感光度平均梯度的测定 |
Photography; Black-and-white aerial camera films; Determination of ISO speed and average gradient |
ISO 783-1999 |
金属材料.高温拉伸试验 |
Metallic materials - Tensile testing at elevated temperature |
ISO 7831-1986 |
电影技术.35mm光学声带还音用的 A式卷片频率响应.还音特性 |
Cinematography; A-chain frequency response for reproduction of 35 mm photographic sound; Reproduction characteristics |
ISO 7832-1987 |
电影技术.光学型音频级试验胶片的光电输出率测野和校准 |
Cinematography; Photoelectric output factor of photographic-type audio-level test films; Measurement and calibration |
ISO 7834-1987 |
铁矿石.砷含量的测定.钼的兰光分光光度计法 |
Iron ores; Determination of arsenic content; Molybdenum blue spectrophotometric method |
ISO 7837-1992 |
肥料.细粒肥料松密度的测定 |
Fertilizers; determination of bulk density (loose) of fine-grained fertilizers |
ISO 7838-1984 |
造船.船体型线.格式和数据组编 |
Shipbuilding; Shiplines; Formats and data organization |
ISO 7839-1984 |
纺织机械和附件.针织机.分类和词汇.三种语言版 |
Textile machinery and accessories; Knitting machines; Classification and vocabulary Trilingual edition |
ISO 7840-1994 |
小型船舶.耐火燃料软管 |
Small craft - Fire-resistant fuel hoses |
ISO 7840-2004 |
小艇.耐火燃油软管 |
|
ISO 7840-2004 |
小艇.耐火燃油软管 |
|
ISO 7841-1988 |
自动疏水阀.蒸汽漏失的测定.试验方法 |
Automatic steam traps; determination of steam loss; test methods |
ISO 7842-1988 |
自动疏水阀.流量测定.试验方法 |
Automatic steam traps; determination of discharge capacity; test methods |
ISO 7844-1985 |
大型钢筋混凝土板之间用连杆和混凝土充填的开槽式垂直连接.实验室的机械试验.切向负荷效应 |
Grooved vertical joints with connecting bars and concrete infill between large reinforced concrete panels; Laboratory mechanical tests; Effect of tangential loading |
ISO 7845-1985 |
承重墙和混凝土地板之间的水平连接.实验室机械试验.通过地板传递的垂直载荷效应和力矩效应 |
Horizontal joints between load-bearing walls and concrete floors; Laboratory mechanical tests; Effect of vertical loading and of moments transmitted by the floors |
ISO 7847-1987 |
动植物脂肪和油.具有-顺式、顺式1和4-二烯结构的多不饱和脂肪酸的测定 |
Animal and vegetable fats and oils; Determination of polyunsaturated fatty acids with a cis,cis 1,4-diene structure |
ISO 7850-1986 |
硬质泡沫塑料.压缩蠕变的测定 |
Cellular plastics, rigid; Determination of compressive creep |
ISO 7851-1983 |
肥料和土壤改良剂.分类.三种语言版 |
Fertilizers and soil conditioners; Classification Trilingual edition |
ISO 7852-1983 |
土方机械.防松螺栓头.外形和尺寸(螺纹尺寸除外) |
Earth-moving machinery; Plough bolt heads; Shapes and dimensions (excluding thread dimensions) |
ISO 7854-1995 |
橡胶或塑料涂覆织物.耐折曲损坏性的测定 |
Rubber- or plastics-coated fabrics - Determination of resistance to damage by flexing |
ISO 7857-1-1983 |
子宫内器件.第1部分:破裂力的测定 |
Intra-uterine devices; Part 1 : Determination of breaking force |
ISO 7857-2-1983 |
子宫内器件.第2部分:消毒方法推荐 |
Intra-uterine devices; Part 2 : Recommendations for disinfection |
ISO 7857-3-1983 |
子宫内器件.第3部分:包装和标签 |
Intra-uterine devices; Part 3 : Packaging and labelling |
ISO 7858-1-1998 |
封闭管道中的水流量的测量.饮用冷水综合测量计.第1部分:规范 |
Measurement of water flow in closed conduits - Combination meters for cold potable water - Part 1: Specifications |
ISO 7858-2-2000 |
封闭管道中的水流量的测量.饮用冷水用综合测量计.第2部分:安装要求 |
Measurement of water flow in closed conduits - Combination meters for cold potable water - Part 2: Installation requirements |
ISO 7858-3-1992 |
封闭管道中水流量的测量.冷饮用水表.组合水表.第3部分:试验方法 |
Measurement of water flow in closed conduits; meters for cold potable water; combination meters; part 3: test methods |
ISO 7859-2000 |
机动脚踏两用车.燃料消耗测量 |
Mopeds - Fuel consumption measurements |
ISO 7860-1995 |
摩托车.燃油消耗测量的方法 |
Motorcycles - Methods of measuring fuel consumption |
ISO 7862-1992 |
客车.在模拟前碰撞时评定成年人约束系统的滑车试验规程 |
Passenger cars; sled test procedure for evaluating adult restraint systems in simulated frontal collision |
ISO 7862-2004 |
道路车辆.通过模拟正面碰撞评价约束系统的滑车试验过程 |
|
ISO 7863-1984 |
高度调节测微计和调整垫块 |
Height setting micrometers and riser blocks |
ISO 7864-1993 |
一次性使用无菌皮下注射针头 |
Sterile hypodermic needles for single use |
ISO 7866-1999 |
气瓶.可再填充的无缝铝合金气瓶.设计,结构和试验 |
Gas cylinders - Refillable seamless aluminium alloy gas cylinders - Design, construction and testing |
ISO 7867-1-1996 |
农用拖拉机和机械用轮胎和轮辋(米制系列).第1部分:轮胎的命名、尺寸、作标记和轮胎/轮辋的调整 |
Tyres and rims (metric series) for agricultural tractors and machines - Part 1: Tyre designation, dimensions, marking and tyre/rim coordination |
ISO 7867-2 Technical Corrigendum 1-1996 |
农用拖拉机和机具用轮胎和轮辋(米制系列).第2部分:使用说明和额定负荷值.技术勘误1 |
Tyres and rims (metric series) for agricultural tractors and machines - Part 2: Service description and load ratings; Technical Corrigendum 1 |
ISO 7867-2-1996 |
农业拖拉机和机械用轮胎和轮辋(米制系列).第2部分:工作描述及荷载能力 |
Tyres and rims (metric series) for agricultural tractors and machines - Part 2: Service description and load ratings |
ISO 787-1-1982 |
颜料和填充剂的一般试验方法.第1部分:颜料颜色的比较 |
General methods of test for pigments and extenders; Part 1 : Comparison of colour of pigments |
ISO 787-1-1982 |
颜料和填充剂的一般试验方法.第1部分:颜料颜色的比较 |
General methods of test for pigments and extenders; Part 1 : Comparison of colour of pigments |
ISO 787-10-1993 |
颜料和填充剂的一般试验方法.第10部分:密度的测定.比重瓶法 |
General methods of test for pigments and extenders; part 10: determination of density; pyknometer method |
ISO 787-11-1981 |
颜料和填充剂的一般试验方法.第11部分:压实后压实容积和表观密度的测定 |
General methods of test for pigments and extenders; Part 11 : Determination of tamped volume and apparent density after tamping |
ISO 787-13-2002 |
颜料和体质颜料的通用试验方法.第13部分:水溶性硫酸盐、氯化物和硝酸盐的测定 |
General methods of test for pigments and extenders - Part 13: Determination of water-soluble sulfates, chlorides and nitrates |
ISO 787-14-2002 |
颜料和体质颜料的通用试验方法.第14部分:水萃取物电阻率的测定 |
General methods of test for pigments and extenders - Part 14: Determination of resistivity of aqueous extract |
ISO 787-15-1986 |
颜料和填充剂的一般试验方法.第15部分:同类着色颜料耐光性的比较 |
General methods of test for pigments and extenders; part 15: comparison of resistance to light of coloured pigments of similar types |
ISO 787-16-1986 |
颜料和填充剂的一般试验方法.第16部分:相对着色力(或等数着色值)的测定和着色颜料还原后的颜色目视比较法 |
General methods of test for pigments and extenders; Part 16 : Determination of relative tinting strength (or equivalent colouring value) and colour on reduction of coloured pigments; Visual comparison method |
ISO 787-17-2002 |
颜料和体质颜料的通用试验方法.第17部分:白色颜料的消色力比较 |
General methods of test for pigments and extenders - Part 17: Comparison of lightening power of white pigments |
ISO 787-18-1983 |
颜料和填充剂的一般试验方法.第18部分:筛渣的测定.机械冲洗步骤 |
General methods of test for pigments and extenders; Part 18 : Determination of residue on sieve; Mechanical flushing procedure |
ISO 787-19-1974 |
颜料的一般试验方法.第19部分:水溶性硝酸盐的测定(水杨酸法) |
General methods of test for pigments; part 19: determination of water-soluble nitrates (Salicylic acid method) |
ISO 787-2-1981 |
颜料和填充剂的一般试验方法.第2部分:在105 ℃挥发物的测定 |
General methods of test for pigments and extenders; Part 2 : Determination of matter volatile at 105 degrees C |
ISO 787-2-1981 |
颜料和填充剂的一般试验方法.第2部分:在105 ℃挥发物的测定 |
General methods of test for pigments and extenders; Part 2 : Determination of matter volatile at 105 degrees C |
ISO 787-21-1979 |
颜料和填充剂的一般试验方法.第21部分:使用烘干介质比较颜料的热稳定性 |
General methods of test for pigments and extenders; part 21: comparison of heat stability of pigments using a stoving medium |
ISO 787-22-1980 |
颜料和填充剂的一般试验方法.第22部分:颜料耐渗色性的比较 |
General methods of test for pigments and extenders; Part 22 : Comparison of resistance to bleeding of pigments |
ISO 787-23-1979 |
颜料和填充剂的一般试验方法.第23部分:密度的测定(用离心机消除夹带的空气) |
General methods of test for pigments and extenders; part 23: determination of density (using a centrifuge to remove entrained air) |
ISO 787-24-1985 |
颜料和填充剂的一般试验方法.第24部分:着色颜料的相对着色力和白色颜料的相对散射力的测定.光度法 |
General methods of test for pigments and extenders; Part 24 : Determination of relative tinting strength of coloured pigments and relative scattering power of white pigments; Photometric methods |
ISO 787-25-1993 |
颜料和填充剂的一般试验方法.第25部分:白色、黑色和着色颜料的全荫系统颜色比较.比色法 |
General methods of test for pigments and extenders; part 25: comparison of the colour, in full-shade systems, of white, black and coloured pigments; colorimetric method |
ISO 787-3-2000 |
颜料和填充剂的一般试验方法.第3部分:水中可溶物质的测定.热萃取法 |
General methods of test for pigments and extenders - Part 3: Determination of matter soluble in water; Hot extraction method |
ISO 787-4-1981 |
颜料和填充剂的一般试验方法.第4部分:水萃取酸度或碱度的测定 |
General methods of test for pigments and extenders; Part 4 : Determination of acidity or alkalinity of the aqueous extract |
ISO 787-5-1980 |
颜料和填充剂的一般试验方法.第4部分:吸油值的测定 |
General methods of test for pigments and extenders; Part 5 : Determination of oil absorption value |
ISO 787-7-1981 |
颜料和填充剂的一般试验方法.第7部分:筛渣的测定.水法.人工操作程序 |
General methods of test for pigments and extenders; Part 7 : Determination of residue on sieve; Water method; Manual procedure |
ISO 787-8-2000 |
颜料和填充剂的一般试验方法.第8部分:水中可溶物质的测定.冷萃取法 |
General methods of test for pigments and extenders - Part 8: Determination of matter soluble in water; Cold extraction method |