标准号 |
中文名称 |
英文名称 |
ISO 6170-1999 |
纺纱机.粗梳机用搓条橡胶 |
(Spinning machinery - Condenser rubbers for cards) |
ISO 6173-1982 |
自由端纺纱机.词汇.三种语言版 |
(Open-end spinning machines; Vocabulary Trilingual edition) |
ISO 6176-1994 |
纺织机械.经纱上浆机.最大有效宽度 |
(Textile machinery - Warp sizing machines - Maximum usable width) |
ISO 6177-1986 |
纺织机械.卷布辊.术语和主要尺寸 |
(Textile machinery; Cloth rollers; Terminology and main dimensions) |
ISO 6178-1983 |
离心机.结构和安全规则.圆柱形转子壳体内切向应力的计算方法 |
(Centrifuges; Construction and safety rules; Method for the calculation of the tangential stress in the shell of a cylindrical centrifuge rotor) |
ISO 6179-1998 |
硫化或热塑橡胶.橡胶薄板和橡胶涂层织物.挥发性液体传播速度的测定(重力测重技术) |
(Rubber, vulcanized or thermoplastic - Rubber sheets and rubber-coated fabrics - Determination of transmission rate of volatile liquids (gravimetric technique)) |
ISO 618-1974 |
纸.信纸包括活页纸 |
(Paper; Articles of stationery that include detachable sheets; Overall trimmed sizes) |
ISO 6182-1-1993 |
火灾防护措施.自动喷水系统.第1部分:喷洒器的要求和试验方法 |
(Fire protection; automatic sprinkler systems; part 1: requirements and test methods for sprinklers) |
ISO 6182-1-2004 |
消防.自动喷水灭火系统.第1部分:洒水喷头的性能要求和试验方法 |
|
ISO 6182-11-2003 |
消防.自动喷水灭火系统.第11部分:吊管架的要求和试验方法 |
(Fire protection - Automatic sprinkler systems - Part 11: Requirements and test methods for pipe hangers ) |
ISO 6182-11-2003 |
消防.自动喷水灭火系统.第11部分:吊管架的要求和试验方法 |
|
ISO 6182-2-1993 |
火灾防护措施.自动喷水系统.第2部分:湿式报警阀.减速箱和水马达报警器 |
(Fire protection; automatic sprinkler systems; part 2: requirements and test methods for wet alarm valves, retard chambers and water motor alarms) |
ISO 6182-3-1993 |
火灾防护措施.自动喷水系统.第3部分:干式管阀的试验方法和要求 |
(Fire protection; automatic sprinkler systems; part 3: requirements and test methods for dry pipe valves) |
ISO 6182-4-1993 |
火灾防护措施.自动喷水系统.第4部分:速启装置的要求和试验方法 |
(Fire protection; automatic sprinkler systems; part 4: requirements and test methods for quick-opening devices) |
ISO 6182-5-1995 |
火灾防护措施.自动喷水系统.第5部分:喷水灭火阀的要求和试验方法 |
(Fire protection - Automatic sprinkler systems - Part 5: Requirements and test methods for deluge valves) |
ISO 6182-7-2004 |
消防.自动喷水灭火系统.第7部分:早期扑灭快速反应洒水喷头的要求和试验方法 |
|
ISO 6183-1990 |
火灾防护设备.房屋用二氧化碳灭火装置.设计和安装 |
(Fire protection equipment; carbon dioxide extinguishing systems for use on premises; design and installation) |
ISO 6184-1-1985 |
防爆系统.第1部分:空气中易燃尘埃爆炸指数的测定 |
(Explosion protection systems; Part 1 : Determination of explosion indices of combustible dusts in air) |
ISO 6184-2-1985 |
防爆系统.第2部分:空气中易燃气体爆炸指数的测定 |
(Explosion protection systems; Part 2 : Determination of explosion indices of combustible gases in air) |
ISO 6184-3-1985 |
防爆系统.第3部分:除粉尘/空气和气体/空气混合物以外的燃料/空气混合物爆炸指数的测定 |
(Explosion protection systems; Part 3 : Determination of explosion indices of fuel/air mixtures other than dust/air and gas/air mixtures) |
ISO 6184-4-1985 |
防爆系统.第4部分:爆炸排除系统效能的测定 |
(Explosion protection systems; Part 4 : Determination of efficacy of explosion suppression systems) |
ISO 6185-1-2001 |
充气船.第1部分:最大电动机功率为4.5KW的船 |
(Inflatable boats - Part 1: Boats with a maximum motor power rating of 4,5 kW) |
ISO 6185-2-2001 |
充气船.第2部分:最大电动机功率为4.5KW至15KW的船 |
(Inflatable boats - Part 2: Boats with a maximum motor power rating of 4,5 kW to 15 kW inclusive) |
ISO 6185-3-2001 |
充气船.第3部分:最大电动机功率为15KW以上的船 |
Inflatable boats - Part 3: Boats with a maximum motor power rating of 15 kW and greater |
ISO 6186-1998 |
塑料.浇注性的测定 |
Plastics - Determination of pourability |
ISO 6187-2001 |
硬质泡沫塑料.易碎性的测定 |
Rigid cellular plastics - Determination of friability |
ISO 6189-1983 |
声学.用于保护听觉的纯音响空气传导阈值的听力测定 |
Acoustics; Pure tone air conduction threshold audiometry for hearing conservation purposes |
ISO 619-1981 |
锰矿石.铬含量的测定.二苯卡巴肼光度测定法和过硫酸银滴定法 |
Manganese ores; Determination of chromium content; Diphenylcarbazide photometric method and silver persulphate titrimetric method |
ISO 6191-1981 |
工业用轻质烯烃.微量水的测定.费歇尔(Karl Fischer)法 |
Light olefins for industrial use; Determination of traces of water; Karl Fischer method |
ISO 6192-1981 |
工业用轻质烯烃.氨的测定.光度法 |
Light olefins for industrial use; Determination of ammonia; Photometric method |
ISO 6194-1-1982 |
旋转轴唇型密封件.第1部分:公称尺寸和公差 |
Rotary shaft lip type seals; Part 1 : Nominal dimensions and tolerances |
ISO 6194-2-1991 |
旋转轴唇型密封件.第2部分:词汇 |
Rotary shaft lip type seals; part 2: vocabulary |
ISO 6194-3-1988 |
旋转轴唇型密封垫.第3部分:储存、运输及安装 |
Rotary shaft lip type seals; part 3: storage, handling and installation |
ISO 6194-4-1999 |
旋转轴唇型密封件.第4部分:性能试验过程 |
Rotary shaft lip type seals - Part 4: Performance test procedures |
ISO 6194-5-1990 |
旋转轴唇型密封件.第5部分:目视缺陷的鉴别 |
Rotary shaft lip type seals; part 5: identification of visual imperfections |
ISO 6195-2002 |
流体动力系统和件.往复作用的活塞杆刮垢环罩.尺寸和公差 |
Fluid power systems and components - Cylinder-rod wiper-ring housings in reciprocating applications - Dimensions and tolerances |
ISO 6196-1-1993 |
缩微摄影技术词汇.第1部分:一般术语 |
Micrographics; Vocabulary; Part 01: General terms |
ISO 6196-10 Technical Corrigendum 1-2004 |
缩微摄影技术.词汇.第10部分:索引.技术勘误1 |
|
ISO 6196-10-1999 |
缩微摄影技术.词汇.第10部分:索引 |
Micrographics - Vocabulary - Part 10: Index |
ISO 6196-2-1993 |
缩微摄影技术.词汇.第2部分:影象位置和记录方法 |
Micrographics; Vocabulary; Part 02: Image positions and methods of recording |
ISO 6196-3-1997 |
缩微摄影技术词汇.第3部分:胶片冲洗 |
Micrographics - Vocabulary - Part 03: Film processing |
ISO 6196-4-1998 |
缩微摄影技术.词汇.第4部分:材料和包装 |
Micrographics - Vocabulary - Part 4: Materials and packaging |
ISO 6196-5-1987 |
缩微摄影技术.词汇.第5部分:影象质量.清晰度和检验.三种语言版本 |
Micrographics; Vocabulary; Part 05: Quality of images, legibility, inspection Trilingual edition |
ISO 6196-6-1992 |
缩微摄影技术.词汇.第6部分:设备 |
Micrographics; vocabulary; Part 06: Equipment |
ISO 6196-7-1992 |
缩微摄影技术.词汇.第7部分:计算机缩微技术 |
Micrographics; Vocabulary; Part 07: Computer micrographics |
ISO 6196-8-1998 |
缩微摄影技术.词汇.第8部分:应用 |
Micrographics - Vocabulary - Part 8: Use |
ISO 6198-1993 |
缩微照相.透明缩微品阅读器的性能特征 |
Micrographics; readers for transparent microforms; performance characteristics |
ISO 6199-1991 |
缩微摄影技术.在16mm和35mm银胶凝型缩微胶卷上的文件缩微摄影.操作规程 |
Micrographics; microfilmimg of documents on 16 mm and 35 mm silver-gelatin type microfilm; operating procedures |
ISO 62-1999 |
塑料.吸水性的测定 |
Plastics - Determination of water absorption |
ISO 6200-1999 |
缩微摄影技术.源文件的第一代银色透明微型胶片.密度规范和试验方法 |
Micrographics - First generation silver-gelatin microforms of source documents - Density specifications and method of measurement |
ISO 6205-1988 |
内河航行船舶.客舱密封系统.基本技术要求 |
Inland navigation vessels; customs sealing systems; basic technical requirements |
ISO 6206-1979 |
工业用化学制品.取样.词汇.两种语言版 |
Chemical products for industrial use; Sampling; Vocabulary Bilingual edition |
ISO 6207-1992 |
无缝镍管和镍合金管 |
Seamless nickel and nickel alloy tube |
ISO 6208-1992 |
镍和镍合金扳.薄扳和带材 |
Nickel and nickel alloy plate, sheet and strip |
ISO 6209-1988 |
橡胶配方配合剂.炭黑.可萃取物溶剂的测定 |
Rubber compounding ingredients; carbon black; determination of solvent extractable material |
ISO 621-1981 |
锰矿石.金属铁含量(不超过2-0/0)的测定.磺基水杨酸光度测定法 |
Manganese ores; Determination of metallic iron content (metallic iron content not exceeding 2 %); Sulphosalicylic acid photometric method |
ISO 6210-1-1991 |
机器人电阻焊枪气瓶.第1部分:一般要求 |
Cylinders for robot resistance welding guns; part 1: general requirements |
ISO 6216-1980 |
造船.内河航行.领航船.分类和基本要求 |
Shipbuilding; Inland navigation; Pilot craft; Classification and basic requirements |
ISO 6217-1982 |
造船.内河航行.领航船.识别涂色和标记 |
Shipbuilding; Inland navigation; Pilot craft; Identification painting and inscriptions |
ISO 6218-1981 |
造船.内河航行.推进式驳船的连接用绞车.主要尺寸 |
Shipbuilding; Inland navigation; Coupling winches for push tows; Main dimensions |
ISO 6219-1983 |
造船.内河船舶.起锚机和起锚绞车 |
Shipbuilding; Inland vessels; Windlasses and anchor capstans |
ISO 622-1981 |
固体矿物燃料.磷含量的测定.还原磷钼酸盐光度法 |
Solid mineral fuels; Determination of phorphorus content; Reduced molybdophosphate photometric method |
ISO 6222-1999 |
水质.可培养微生物的计数.通过对营养琼脂培养基培养的计群法 |
Water quality - Enumeration of culturable micro-organisms - Colony count by inoculation in a nutrient agar culture medium |
ISO 6224-1995 |
输水通用织物增强的塑料软管.规范 |
Plastics hoses, textile-reinforced, for general-purpose water applications - Specification |
ISO 6225-1-1984 |
天然生橡胶.蓖麻油含量的测定.第1部分:蓖麻油甘油脂含量的测定.薄层色谱光度法 |
Rubber, raw, natural; Determination of castor oil content; Part 1 : Determination of castor oil glycerides content; Thin layer chromatographic method |
ISO 6225-2-1990 |
天然生橡胶.蓖麻油含量的测定.第2部分:蓖麻酸总含量的测定.气相色谱法 |
Rubber, raw, natural; determination of castor oil content; part 2: determination of total ricinoleic acid content by gas chromatography |
ISO 6227-1982 |
工业用化学制品.测定氯离子的一般方法.电势测定法 |
Chemical products for industrial use; General method for determination of chloride ions; Potentiometric method |
ISO 6228-1980 |
工业用化学制品.通过还原和滴定分析法测定微量硫化合物(如硫酸盐)的一般方法 |
Chemical products for industrial use; General method for determination of traces of sulphur compounds, as sulphate, by reduction and titrimetry |
ISO 6229-1980 |
工业用六氟硅酸钠.游离二氧化硅含量的测定.重量分析法 |
Sodium hexafluorosilicate for industrial use; Determination of free silica content; Gravimetric method |
ISO 623-1974 |
纸和纸板.硬纸夹和卷宗.尺寸 |
Paper and board; Folders and files; Sizes |
ISO 6230-1989 |
锰矿石.用筛分法测定粒度分配 |
Manganese ores; determination of size distribution by sieving |
ISO 6233-1983 |
锰矿石和锰精矿.钙和镁含量的测定.乙二胺四乙酸(EDTA)滴定法 |
Manganese ores and concentrates; Determination of calcium and magnesium contents; EDTA titrimetric method |
ISO 6234-1981 |
银行业务.认可印鉴册及其缩微胶片的显示 |
Bank operations; Authorized signature lists and their representation on microfiche |
ISO 6235-1995 |
生橡胶.聚苯乙烯块含量的测定.臭氧分解法 |
Rubber, raw - Determination of block polystyrene content - Ozonolysis method |
ISO 6237-1987 |
粘合剂.木材与木材粘结剂.用拉伸负荷测定剪切强度 |
Adhesives; Wood-to-wood adhesive bonds; Determination of shear strength by tensile loading |
ISO 6237-2003 |
粘合剂.木材与木材粘结体.用拉伸负荷测定剪切强度 |
(Adhesives - Wood-to-wood adhesive bonds - Determination of shear strength by tensile loading ) |
ISO 6237-2003 |
粘合剂.木材与木材粘结体.用拉伸负荷测定剪切强度 |
|
ISO 6238-2001 |
粘合剂.木材与木材的粘合剂.用压缩负荷测定剪切强度 |
Adhesives - Wood-to-wood adhesive bonds - Determination of shear strength by compressive loading |
ISO 6240-1980 |
建筑物性能标准.内容和说明 |
Performance standards in building; Contents and presentation |
ISO 6241-1984 |
建筑物性能标准.标准的制定原则和所考虑的因素 |
Performance standards in building; Principles for their preparation and factors to be considered |
ISO 6242-1-1992 |
建筑结构.用户要求的表示法.第1部分:热量的要求 |
Building construction; expression of users` requirements; part 1: thermal requirements |
ISO 6242-2-1992 |
建筑结构.用户要求的表示法.第2部分:空气纯度要求 |
Building construction; expression of users` requirements; part 2: air purity requirements |
ISO 6242-3-1992 |
建筑结构.用户要求的表示法.第3部分:声学要求 |
Building construction; expression of users` requirements; part 3: acoustical requirements |
ISO 6243-1997 |
建筑设计气候.符号的提案系统 |
Climatic data for building design - Proposed system of symbols |
ISO 6244-1982 |
石油蜡和矿脂.滴熔点的测定 |
Petroleum waxes and petrolatums; Determination of drop melting point |
ISO 6245-2001 |
石油产品.灰分的测定 |
Petroleum products - Determination of ash |
ISO 6246 Technical Corrigendum 1-1998 |
石油产品.轻质和中度馏出燃料的含胶量.喷射蒸发法.技术勘误1 |
Petroleum products - Gum content of light and middle distillate fuels - Jet evaporation method; Technical Corrigendum 1 |
ISO 6246-1995 |
石油产品.轻度和中度蒸馏燃料的胶含量.喷射蒸发法 |
Petroleum products - Gum content of light and middle distillate fuels - Jet evaporation method |
ISO 6247 Technical Corrigendum 1-1999 |
石油产品.润滑油发泡特性的测定.技术勘误1 |
Petroleum products - Determination of foaming characteristics of lubricating oils; Technical Corrigendum 1 |
ISO 6247-1998 |
石油产品.润滑油发泡特性的测定 |
Petroleum products - Determination of foaming characteristics of lubricating oils |
ISO 6249-1999 |
石油产品.燃气轮机燃料的热氧化稳定性的测定.JFTOT法 |
Petroleum products - Determination of thermal oxidation stability of gas turbine fuels - JFTOT method |
ISO 625 Technical Corrigendum 1-1996 |
固体矿物燃料.碳和氢含量的测定.李比希(Liebig)法.技术勘误1 |
Solid mineral fuels - Determination of carbon and hydrogen - Liebig method; Technical Corrigendum 1 |
ISO 625-1996 |
固体矿物燃料.碳和氢含量的测定.李比希氏法 |
Solid mineral fuels - Determination of carbon and hydrogen - Liebig method |
ISO 6250-1997 |
石油产品.航空燃料的水反应的测定 |
Petroleum products - Determination of the water reaction of aviation fuels |
ISO 6251-1996 |
液化石油气.对铜的腐蚀性.铜片试验 |
Liquefied petroleum gases - Corrosiveness to copper - Copper strip test |
ISO 6252-1992 |
塑料.环境应力破裂(ESC)测定.恒定-拉伸-应力法 |
Plastics; determination of Environmental Stress Cracking (ESC); constant-tensile-stress method |
ISO 6255-1997 |
轿车.轿车后窗洗涤和擦拭系统.试验方法 |
Passenger cars - Rear-window washing and wiping systems - Test methods |
ISO 6257-2002 |
铝生产用碳素材料.电极用沥青.取样 |
Carbonaceous materials used in the production of aluminium - Pitch for electrodes - Sampling |
ISO 6258-1985 |
核电站.防地震的设计 |
Nuclear power plants; Design against seismic hazards |
ISO 6259-1-1997 |
热塑管.拉伸特性的测定.第1部分:通用试验方法 |
Thermoplastics pipes - Determination of tensile properties - Part 1: General test method |
ISO 6259-2-1997 |
热塑管.拉伸特性的测定.未增塑聚氯乙烯(PVC-U),氯化聚氯乙烯(PVC-C)和耐冲击聚氯乙烯(PVC-HI)制管 |
Thermoplastics pipes - Determination of tensile properties - Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI) |
ISO 6259-3-1997 |
热塑管.拉伸特性的测定.第3部分:聚烯烃管 |
Thermoplastic pipes - Determination of tensile properties - Part 3: Polyolefin pipes |
ISO 6260-1984 |
邮汇付款单 |
Mail payment orders |
ISO 6261-1995 |
配用于可转位刀片的镗杆(有柱形刀柄的刀具夹).名称与符号 |
Boring bars (tool holders with cylindrical shank) for indexable inserts - Designation |
ISO 6262-1-1982 |
配用于可转位刀片的端铣刀.第1部分:扁平直柄端铣刀 |
End mills with indexable inserts; Part 1: End mills with flatted parallel shank |
ISO 6262-2-1982 |
配用于可转位刀片的端铣刀.第2部分:莫氏锥柄端铣刀 |
End mills with indexable inserts; part 2: End mills with Morse taper shank |
ISO 6263-1997 |
液压传动.补偿式流量控制阀.装配面 |
Hydraulic fluid power - Compensated flow-control valves - Mounting surfaces |
ISO 6264-1998 |
液压传动.减压阀.装配面 |
Hydraulic fluid power - Pressure-relief valves - Mounting surfaces |
ISO 6265-1992 |
高山雪橇.畸形负荷和断裂页荷测定 |
Alpine skis; determination of deformation load and breaking load |
ISO 6266-1980 |
高山雪橇.疲劳指数的测定.周期性载荷试验 |
Alpine skis; Determination of fatigue indexes; Cyclic loading test |
ISO 6267-1980 |
高山雪橇.弯曲振动的测量 |
Alpine skis; Measurement of bending vibrations |
ISO 6270-1-1998 |
涂料和清漆.耐湿度的测定.第1部分:连续冷凝作用 |
Paints and varnishes - Determination of resistance to humidity - Part 1: Continuous condensation |
ISO 6271-1997 |
透明液体.用铂钴标度评定颜色 |
Clear liquids - Estimation of colour by the platinum-cobalt scale |
ISO 6272-1-2002 |
涂料和清漆.快速毁坏(抗冲击)试验.第1部分:大面积砸痕的落锤试验 |
Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter |
ISO 6272-2-2002 |
涂料和清漆.快速毁坏(抗冲击)试验.第2部分:小面积砸痕的落锤试验 |
Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter |
ISO 6274-1982 |
混凝土.集料的筛分析 |
Concrete; Sieve analysis of aggregates |
ISO 6275-1982 |
凝固的混凝土.比重的测定 |
Concrete, hardened; Determination of density |
ISO 6276-1982 |
压实的新搅拌混凝土.比重的测定 |
Concrete, compacted fresh; Determination of density |
ISO 6278-1980 |
滚针轴承.滚道滚针.外形尺寸 |
Needle roller bearings; Track rollers; Boundary dimensions |
ISO 6279-1979 |
滑动轴承.整体轴承用铝合金 |
Plain bearings; Aluminium alloy for solid bearings |